Autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 of 79 2u autoloader 6.4 ® lto3 user reference manual document no: docsp 301283 date: aug., 2005.
Warnings precautions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 of 79 product overview product name p/n description lto3 autoloader 6.4 8330 7071 00 1 drive & 8 slots, 2u, accessories product name description scsi cable terminator power cord (1x eu version, 1x us version)...
Warnings precautions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 of 79 service & support information: europe tandberg data gmbh feldstr. 81 d-44141 dortmund germany phone: 0049 – (0)231 – 5436 142 fax: 0049 – (0)231 – 5436 143 usa inostor inc. (a tandberg data company ) 13...
Warnings precautions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 of 79 1 warnings ! ! Important all safety and operating instructions should be read before this product is operated, and should be retained for future reference. This unit has been engineered and manufactured...
Warnings precautions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 of 79 1.1 precautions n do not use oil, solvents, gasoline, paint thinners or insecticides on the unit. N do not expose the unit to moisture, to temperatures higher than 60 °c (140 °f) or to extreme low tempe...
Warnings user guide autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 of 79 1.3 user guide this specification describes the functional, performance, and environmental specifications of the autoloader. Contents of this user reference manual n quick start guide n features and phys...
Contents autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 of 79 2 contents 1 warnings ................................ ............................................................................................ 4 1.1 precautions ...................................................
Contents autoloader lto3 – user reference manual rev. 1.01 tandberg data page 8 of 79 8.5 configuration ............................................................................................................ 36 8.6 operation .........................................................................
Contents autoloader lto3 – user reference manual rev. 1.01 tandberg data page 9 of 79 12.4 environmental specifications ..................................................................................... 70 12.4.1shock and vibration ....................................................................
Tables autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 0 of 79 3 tables table 1 autoloader features................................................................................................ ... 15 table 2 scsi interface ......................................................
Figures autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 1 of 79 4 figures figure 1 ac line cord, scsi terminator .................................................................................... 12 figure 2 power switch .........................................................
Quick start guide autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 2 of 79 5 quick start guide defaults note: the following defaults have been set at the factory. Ldr scsi id 0 drv scsi id 5 operating mode sequential figure 1 ac line cord, scsi terminator 1. Install ac line cor...
Quick start guide autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 3 of 79 figure 3 operator panel 5. Press any button on the operator panel to change to interaction mode. 6. Choose the "go offline" menu and press . 7. Choose the "commands" menu and press . 8. Choose "import", ...
Features and physical description equipment description autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 4 of 79 6 features and physical description 6.1 equipment description the autoloader provides automated data storage, archival, backup, and retrieval for a range of systems,...
Features and physical description features autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 5 of 79 6.2 features the autoloader includes the following features: n a carousel encircles the tape drive and positions the specified cartridge slot in front of the tape drive. A roboti...
Features and physical description component descriptions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 6 of 79 6.3 component descriptions the following sections describe the major components of the autoloader. Front panel components figure 5 front panel components ( 1 ) cart...
Features and physical description component descriptions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 7 of 79 back panel components figure 6 back panel components ( 1 ) scsi connectors the autoloader has two wide scsi connectors for connecting the autoloader and tape drive ...
Features and physical description component descriptions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 8 of 79 tape drive the autoloader contains one tape drive. The tape drive can sustain a maximum data transfer rate of 280 mb per second (compressed) and can store up to 800...
Features and physical description component descriptions autoloader lto3 – user reference manual rev. 1.01 tandberg data page 1 9 of 79 data cartridges the tape drive reads and writes to lto tape data cartridges. The capacity and transfer rates are listed in 0. Caution wrong tapes! Damages of the ta...
Installation and setup installing the optional remote management unit (rmu) autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 0 of 79 7 installation and setup this chapter describes: n installing the optional remote management unit (rmu) n installing the optional bar code reader...
Installation and setup installing the optional bar code reader (bcr) autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 1 of 79 figure 8 location of the protective coveri ng for the rmu rail 3. Align the lan card in the rails and insert into the unit. 4. Fix the unit with the sup...
Installation and setup installing the optional bar code reader (bcr) autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 2 of 79 7.2.3 mounting instructions: caution electro static discharge! Destruction of the esd sensitive components. Please touch unit cover or rear panel before...
Installation and setup installing the optional bar code reader (bcr) autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 3 of 79 7.2.4 configuration of the barcode reader 1. Enable barcode reader through the operator panel. Select menu item configuration/barcode reader and set bcr...
Installation and setup installing the autoloader as a desktop unit autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 4 of 79 7.3 installing the autoloader as a desktop unit warning weights on the autoloader! Destruction of the autoloader's chassis. The autoloader should not be s...
Installation and setup installing the autoloader in a rack autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 5 of 79 7.4 installing the autoloader in a rack you have to install the autoloader into a standard 19-inch rack. Required tools: n phillips screwdriver, size 2 n torx wre...
Installation and setup installing the autoloader in a rack autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 6 of 79 3. Install the cage clip-nuts (for racks with square mounting holes) from the back side of each rail. Figure 13 attaching cage cilp nuts to a rack with square hol...
Installation and setup installing the autoloader in a rack autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 7 of 79 7.4.3 install the rack front mount brackets on the autoloader 1. Determine on which side of the autoloader the rack mount brackets will be attached (see figure 15...
Installation and setup running library verify test autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 8 of 79 7.4.5 connecting power 1. Connect the pcc cable (included with your rack mount kit) to the rear of the autoloader. 2. Connect the other end of the pcc cable to your rack’...
Installation and setup connecting the autoloader to the server autoloader lto3 – user reference manual rev. 1.01 tandberg data page 2 9 of 79 7.6 connecting the autoloader to the server the autoloader has to be attached to a scsi/lvd system. Cabling is required for the tape drive interface and the r...
Operation and maintenance general guidelines autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 0 of 79 8 operation and maintenance this chapter describes the requirements for using the autoloader, including information about: n general guidelines n powering on the system n power...
Operation and maintenance powering on the sys tem autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 1 of 79 if the autoloader detects that a cartridge is loaded when it first comes alive, the following status will be displayed on the operator panel: drive loaded 12345 -78 seq in...
Operation and maintenance using the operator panel and menu options autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 2 of 79 the 4 leds (1-4) are updated during power up and reset sequences. Upon power up or software reset, the autoloader will illuminate all leds as soon as pow...
Operation and maintenance operational modes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 3 of 79 ( 6 ) enter, button [ ↵ ] it is used in interaction mode. Push the enter button to go to a sub menu or to force a robotic action. ( 7 ) next, button [+] it is used in interactio...
Operation and maintenance operational modes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 4 of 79 8.4.3 sequential mode in sequential mode the media exchanger is no longer visible on t he scsi bus. Cartridge replacements are initiated by an ‘unload’ command sent to the drive...
Operation and maintenance operational modes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 5 of 79 8.4.6 menu structure and options ocp user interaction mode go online (inv. Status) any key commands (inv. Status) information (inv. Status) cancel enter configuration (inv. Stat...
Operation and maintenance configuration autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 6 of 79 8.5 configuration for most installations, the default configuration of the autoloader does not need to be changed. For further information see thinstor ® plus lto3 autoloader – oper...
Operation and maintenance performing autoloader and tape drive autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 7 of 79 8.7.2 bulk exchange the menu item bulk exchange was designed to make the autoloader more user friendly. This item enables a user to import or export a specifi...
Operation and maintenance performing autoloader and tape drive autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 8 of 79 note: the tape drive can also report its cleaning requirements to the application software. Your application may notify you when the tape drive needs cleaning...
Operation and maintenance shipping autoloader lto3 – user reference manual rev. 1.01 tandberg data page 3 9 of 79 performing routine maintenance and service the autoloader requires no routine maintenance. If necessary, you can use touch-up paint on the housing. Touch -up paint is available for cover...
Troubleshooting and diagnostics general guidelines autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 0 of 79 9 troubleshooting and diagnostics 9.1 general guidelines the autoloader includes features to support troubleshooting and diagnostic operations. If an autoloader error occ...
Troubleshooting and diagnostics determining a problem autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 1 of 79 9.2.1 viewing drive error codes via the ocp 1. From the ocp, press enter to access the information menu. 2. Press next to access drive info. 3. Press next or previous ...
Troubleshooting and diagnostics determining a problem autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 2 of 79 2. Check if air flows from the rear fan? Yes: n proceed with step 3. No: n from serial port hyperterminal session, select fct command. N if fan remains off, replace re...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 3 of 79 9.4 error messages and error codes this chapter describes error codes and associated sub codes of the autoloader. The codes should be used for analyzing failu...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 4 of 79 ddd:hh:mm:ss:hh ddd: days hh: hours mm: minutes ss: seconds hh: 1/100 second the time stamp is set at zero at system start up. The complete error log can be p...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 5 of 79 19h scsi bus type changed to lvd 1ah invalid cleaning cartridge 1bh invalid upgrade tape 1ch cleaning requested 1dh-1fh reserved 9.4.5 recovered errors 20h – ...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 6 of 79 42h slot empty during cartridge loading 43h cleaning tape expired 44h cleaning failed 45h-4fh reserved 9.4.7 illegal request errors 50h – 6fh error code descr...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 7 of 79 69h bad sequence number 6ah wrong checksum 6bh command unspecified 6ch configuration problem: no bar code reader installed 6dh flash image does not fit boot c...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 8 of 79 9.4.10 robotic control errors 81h – 8fh error code description recommended action 81h invalid internal command error. This error indicates that the robotic re...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 4 9 of 79 9.4.11 function errors 90h – 9fh error code description recommended action 90h mechanical initialization failure. The robotic wasn’t able to get into its safe...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 0 of 79 9.4.12 low level axis errors a0h – afh error code description recommended action a0h belt axis error. Error during cartridge carrier movement (position not fo...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 1 of 79 9.4.13 electronic hardware errors b0h – b9h error code description recommended action b0h rom error. A defective rom was detected. Retry operation, after seve...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 2 of 79 9.4.15 barcode errors c0h – cfh error code description recommended action c0h library verify test. Autoloader has detected different reading results according...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 3 of 79 14h end pattern missing 15h drive busy – command rejected 16h general drive error 17h byte stuffing error 18h command negative acknowledged 21h carrier state ...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 4 of 79 41h slider home error. Slider home position not reached. 42h slider forwa rd positioning error. Slider position in forward direction not reached. 43h slider c...
Troubleshooting and diagnostics error messages and error codes autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 5 of 79 91h no drive activity after the load operation 92h timeout while loading cartridge 93h no drive activity after the unload operation 94h timeout while unloadin...
Troubleshooting and diagnostics access protocol autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 6 of 79 c drive needs to be cleaned drive determines that it needs to be cleaned. This condition clears when drive has been cleaned. H reserved for future use j reserved for future ...
Analysis procedures power/external fan analysis autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 7 of 79 10 analysis procedures 10.1 power/external fan analysis if the autoloader does not power on: 1. Ensure power cord is plugged in at the autoloader and at the electrical outle...
Analysis procedures bcr analysis autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 8 of 79 10.3 bcr analysis if the server (host) has reported inventory problems relating to inability to read bar code labels, or, if some or all of the cartridge labels are not being displayed on ...
Scsi interface specification cable and terminator requirements autoloader lto3 – user reference manual rev. 1.01 tandberg data page 5 9 of 79 11 scsi interface specification the autoloader has a standard scsi interface. This chapter provides requirements and specifications for the scsi interface, in...
Scsi interface specification scsi communications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 0 of 79 scsi cable length the maximum allowable cable length for a low-voltage differential scsi bus, including all internal and external cables, is specified as follows: if you ha...
Scsi interface specification scsi communications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 1 of 79 11.2.1 scsi messages the initiator and the target use the scsi message system to manage the physical path. The following table lists the messages supported by the autoloa d...
Scsi interface specification scsi communications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 2 of 79 bus device reset 0ch the initiator instructs the autoloader to reset all of its current i/o operations for all initiators. The autoloader releases the scsi bus into the bus...
Scsi interface specification scsi communications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 3 of 79 mode sense (10 bytes) 5ah reports its operating mode parameters to the initiator. Move medium (12 bytes) a5h moves a cartridge from one location to another. Position to ele...
Scsi interface specification scsi communications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 4 of 79 status bytes after the autoloader executes a command, it issues a status byte to the initiator to indicate whether the command completed successfully. The following table d...
Scsi interface specification elements and element addresses autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 5 of 79 11.3 elements and element addresses 11.3.1 elements elements are the locations in the autoloader that can accept a cartridge. The autoloader includes three types...
Scsi interface specification elements and element addresses autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 6 of 79 figure 21 default element addresses (identical to the element indexes number element description element address element index 1 cartridge slot 1 1h 1 2 cartridg...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 7 of 79 12 product specifications this chapter provides the following information: n size and weight n performance specifications n power specifications n environmental specifications n shipping specificati...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 8 of 79 autoloader self-test times each time the autoloader is powered on, it performs a power-on self-test (post). Post includes a self-test of the control electronics, initialization of the mechanical com...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 6 9 of 79 12.3 power specifications ac power the autoloader has automatic ac input voltage selection and accepts the input voltages shown in the following table. It is capable of continuous operation when the...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 0 of 79 12.4 environmental specifications specification operating 1 ) storage 2) or non- operating 3) transportation 4 ) ambient temperature range +10 °c to +35 °c (+50 °f to +95 °f) –40 °c to +60 °c (–40 °...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 1 of 79 12.4.1 shock and vibration the autoloader meets the shock and vibration criteria described in the following sections. Shock specifications the autoloader will operate normally after experiencing sho...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 2 of 79 transportation 3 ) according bdt wn-72077 swept sine applied during non -operation 6 ) 5 to 500 to 5 hz table 17 vibration specifications 1) a 0.3 g rms random vibration spectrum is applied to the b...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 3 of 79 12.6 safety and regulatory agency compliance this section describes the autoloader's compliance with safety and regulatory agency standards: ! ! Important to comply with the following regulations an...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 4 of 79 radiated and conducted radio frequency emissions (emi) the autoloader meets the require ments for radiated and conducted emissions as defined by the following standards: n fcc rules and regulations,...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 5 of 79 power frequency magnetic field immunity the autoloader complies with en 61000-4 -8:1995, electromagnetic compatibility (emc), part 4: testing and measurement techniques, section 8: power frequency m...
Product specifications autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 6 of 79 ce notice marking by the symbol ce indicates compliance of this tape library to the emc (electromagnetic compatibility) directive of the european community. Such marking is indicative that this tape...
Index autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 7 of 79 13 index a ac power cord specifications...................................68 specifications...........................................68 acces protocol............................................55 accessories.........
Index autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 8 of 79 error code descript ion ......................................42 log example ............................................42 media related ...........................................57 messages and codes ...............
Index autoloader lto3 – user reference manual rev. 1.01 tandberg data page 7 9 of 79 q quick start ................................ ..................11 r rack installation ................................ .........24 rack mount kit...................................... 14, 18 regulations .............