- DL manuals
- TANDBERG
- Media Converter
- E5714 DSNG Voyager
- Reference Manual
TANDBERG E5714 DSNG Voyager Reference Manual - page 268
Technical Specification
Page B-28
Reference Guide: E57xx DSNG and DENG Voyager Encoder
ST.RE.E10076.3
Table B.43: DVB ASI Out 1 Connector (Disabled)
Item Specification
Safety status
SELV
Connector designation
DVB ASI OUT 1
Connector type
BNC
Connector impedance
75
Data coding
8B/10B
Channel rate
270 Mbit/s
Specification
DVB A010 rev 1 (Asynchronous Serial Interface)
LEDs
Table B.44: DVB ASI In 1, 2 and 3 - LED Indications
Item Specification
Red LED
Input ASI lock
On
No lock on ASI (8B/10B coding)
Off
Input ASI lock OK
Green LED
Packet size
Off
Not locked to MPEG packets
Flash (1:3 mark:space)
188 byte packets
Flash (3:1 mark:space)
204 byte packets
Table B.45: DVB ASI Out 1 - LED Indications
Item Specification
Red LED
On Output
disabled
Off
Output enabled
Green LED
Off
Output not in use
Flash (1:3 mark:space)
188 byte packets output
Flash (3:1 mark:space)
204 byte packets output
Summary of E5714 DSNG Voyager
Page 1
St.Re.E10076.3 issue 3 english (uk) reference guide e5714/e5740-xxx dsng, e5750 deng voyager encoder build version 3.6.0 and later 1u encoder 2u encoder.
Page 2
Preliminary pages page ii reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 issue 3 first published in 2005 by: t andberg t elevision l td r egistered a ddress : u nit 2 s trategic p ark , c omines w ay , h edge e nd , s outhampton , h ampshire , so30 4da registered company number ...
Page 3: List of Contents
Preliminary pages reference guide: e57xx dsng and deng voyager encoder page iii st.Re.E10076.3 list of contents chapter 1: introduction to the basic encoder gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and connectors on the fro...
Page 4: About This Reference Guide
Preliminary pages page iv reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 about this reference guide this reference guide provides instructions and information for the installation, operation of the encoder. This reference guide should be kept in a safe place for reference for th...
Page 5: Acknowledgements
Preliminary pages reference guide: e57xx dsng and deng voyager encoder page v st.Re.E10076.3 acknowledgements general all best endeavours have been made to acknowledge registered trademarks and trademarks used throughout this reference guide. Any notified omissions will be rectified in the next issu...
Page 6: Warnings, Cautions and Notes
Preliminary pages page vi reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 warnings, cautions and notes heed warnings all warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or damage where warni...
Page 7: Contact Information
Preliminary pages reference guide: e57xx dsng and deng voyager encoder page vii st.Re.E10076.3 contact information tandberg television customer services support services our primary objective is to provide first class customer care that is tailored to your specific business and operational requireme...
Page 8: Technical Training
Preliminary pages page viii reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 technical training training courses tandberg television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. Tandberg can provid...
Page 9: Contents
Reference guide: e57xx dsng and deng voyager encoder page 1-1 st.Re.E10076.3 chapter 1 1. Introduction to the basic encoder contents 1.1 scope of this reference guide ................................. 1-3 1.1.1 who should use this reference guide....... 1-3 1.1.2 build version .........................
Page 10
Introduction to the basic encoder page 1-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 list of figures figure 1.1: 1u encoder front view ............................................... 1-4 figure 1.2: 2u encoder front view ............................................... 1-4 f...
Page 11: 1.1
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-3 st.Re.E10076.3 1.1 scope of this reference guide 1.1.1 who should use this reference guide this reference guide is written for operators/users of the 1u and 2u voyager encoders to assist in the installati...
Page 12: 1.2
Introduction to the basic encoder page 1-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 1.1: 1u encoder front view figure 1.2: 2u encoder front view table 1.2: equipment model descriptions model number marketing code description e5714 encoder m2/voy/e5714 1u mpeg-2 dsng...
Page 13: 1.2.2 Dsng
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-5 st.Re.E10076.3 the encoder has one card, containing a single video encoder, two stereo audio encoders (dual standard mpeg-1 (layer 2)/dolby digital (ac-3) 4 ), composite video decoder, ca 5 , data input a...
Page 14: 1.2.3 Deng
Introduction to the basic encoder page 1-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 e5714 the satellite modulator within the e5714 supports qpsk modulation in accordance with en 300 421 (dvb-s). It provides a main and monitoring if output. The if frequency can be tuned bet...
Page 15: 1.3
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-7 st.Re.E10076.3 1.3 summary of features 1.3.1 video encoding mpeg-2 encoding the encoder processes a broadcast-standard video signal into a compressed encoded bit-stream in accordance with: • the mpeg-2 ma...
Page 16
Introduction to the basic encoder page 1-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 • fully exhaustive motion estimation • an internal frame synchroniser (see internal frame synchroniser on page 1-8) • support for active format descriptor (afd) (see chapter 4, operating th...
Page 17: 1.3.2 Audio
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-9 st.Re.E10076.3 output on video loss the encoder can be software-configured to show, in the event of video input loss, either: • a test pattern (with or without ident text) • a freeze frame (with or withou...
Page 18
Introduction to the basic encoder page 1-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 audio channels the encoder base board is capable of processing two stereo pairs, from any of the following 17 : • sdi embedded source • digital source aes/ebu • analogue source, terminatio...
Page 19: 1.3.3
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-11 st.Re.E10076.3 dolby digital (ac-3) dolby digital (ac-3) audio encoding incorporates digital normalisation, preprocessing (filtering), dynamic range compression and the addition of bit-stream information...
Page 20: 1.3.4 Data
Introduction to the basic encoder page 1-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 • vitc 18 (ebu and smpte) vitc extraction from line 16 or 22 for 625-line systems (ebu definitions), or line 14 for 525-line systems is supported. • programme delivery control (pdc), via i...
Page 21: 1.3.6 If
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-13 st.Re.E10076.3 1.3.6 if modulation e5714 the internal satellite modulator within the e5714 supports qpsk modulation in accordance with en 300 421 (dvb-s). It provides a main and monitoring if output. The...
Page 22: 1.4 Guided
Introduction to the basic encoder page 1-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 1.4 guided tour 1.4.1 enclosure there are two sizes of enclosure, 1u and 2u versions. The enclosure is used as a stand-alone unit. All inputs and outputs are via rear panel connectors. 1.4...
Page 23: 1.4.3
Introduction to the basic encoder reference guide: e57xx dsng and deng voyager encoder page 1-15 st.Re.E10076.3 note… current versions of the 1u encoder may not have this switch fitted. Figure 1.6: stand-by switch figure 1.7: 2u encoder front panel indicators 1.4.3 rear panel description introductio...
Page 24: 1.4.4
Introduction to the basic encoder page 1-16 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 1.4.4 boards in the basic encoder the basic encoder contains two boards mounted horizontally in the enclosure (see table 1.5). Option modules can be fitted in the remaining slots (see equi...
Page 25: Contents
Reference guide: e57xx dsng and deng voyager encoder page 2-1 st.Re.E10076.3 chapter 2 2. Installing the equipment contents 2.1 introduction ............................................................... 2-3 2.1.1 read this first! ............................................ 2-3 2.1.2 general.........
Page 26
Installing the equipment page 2-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.7 powering up/down..................................................2-23 2.7.1 before powering up....................................2-23 2.7.2 powering up ...........................................
Page 27: 2.1 Introduction
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-3 st.Re.E10076.3 2.1 introduction 2.1.1 read this first! The encoder must be handled carefully and thoughtfully to prevent safety hazards and damage. It is usually supplied as part of a system installed by tandberg ...
Page 28: 2.2 Preliminary
Installing the equipment page 2-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 fcc this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection ...
Page 29: 2.3.2 Cable
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-5 st.Re.E10076.3 figure 2.1: fitting the encoder into a rack note… current versions are not fitted with the standby switch shown above. 2.3.2 cable routing power supply cables should be routed so that they are not l...
Page 30
Installing the equipment page 2-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 the unit is designed for stationary or fixed use only. Ensure it is firmly and safely located and has an adequate through-flow of air. Allow at least 50 mm free air-space at each side of the equipme...
Page 31: 2.4
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-7 st.Re.E10076.3 2.4 ac mains operating voltage and earthing 2.4.1 ac power supply caution... This product should be operated only from the type of power source indicated on the marking label. If you are not sure of...
Page 32
Installing the equipment page 2-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 the unit has a technical earth terminal (marked with ) located at the rear panel. Its use is recommended. This is not a protective earth for electric shock protection. The terminal is provided to: 1...
Page 33: 2.5
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-9 st.Re.E10076.3 2.5 -48 vdc power supply 2.5.1 dc power supply note… only model m2/voy/e5750/48v uses a dc power supply. Caution... This product should be operated only from the type of power source indicated on th...
Page 34: 2.5.3
Installing the equipment page 2-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.5.3 connecting the equipment to the dc power supply connect the encoder to the local dc power supply as follows. 1. Local dc power supply ensure the local dc supply is isolated. 2. Encoder ensure...
Page 35: 2.6
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-11 st.Re.E10076.3 2.6 signal connections for the basic unit 2.6.1 introduction all signal connectors are located at the rear panel of the encoder. For a detailed interface specification see annex b, technical specif...
Page 36: 2.6.2
Installing the equipment page 2-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 2.6: e5740-l-band (2u) rear panel component parts and connectors figure 2.7: e5750 (2u) rear panel component parts and connectors 2.6.2 connecting up the basic encoder once the unit has been...
Page 37: 2.6.3 Power
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-13 st.Re.E10076.3 figure 2.8: equipment connections for the basic unit do not move or install equipment whilst it is still attached to the mains supply. Ensure esd precautions are observed whilst interconnecting equ...
Page 38: 2.6.5 Video
Installing the equipment page 2-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.6.5 video inputs sdi in a 75 Ω bnc connector provides a serial digital video input to the unit. See chapter 4, operating the equipment locally, video input option for the types of video and selec...
Page 39: 2.6.6 Audio
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-15 st.Re.E10076.3 table 2.4: comp video connector pin signal centre video input screen video input return impedance 75 Ω 2.6.6 audio inputs connect the audio cable to the audio in connector. The 15-way, d-type male ...
Page 40: 2.6.7
Installing the equipment page 2-16 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.6.7 asi out 1, 2 and 3 outputs connect the multiplexer or modulator asi cable to the appropriate asi out connector, using good quality 75 Ω coaxial cable (for example, bbc psf 1/3). A 75 Ω bnc co...
Page 41
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-17 st.Re.E10076.3 table 2.8: alarm connector pin signal pin signal 1 ground 6 fail (no) 2 fail (common) 7 fail (nc) 3 alarm (no) 8 alarm (common) 4 alarm (+) (nc) 9 reset 2 (internally grounded) 5 reset 1 (internall...
Page 42: 2.6.9 Data
Installing the equipment page 2-18 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.6.9 data rs-232 connector rs-232 data is available on the base board. Table 2.10: rs-232 data connector (base board) - asynchronous remote (dte) male encoder rs-232 (dte) female signal name pin s...
Page 43
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-19 st.Re.E10076.3 note… signal names are with respect to a dte in accordance with the rs-422 specification. A is positive and b is negative. Voyager modulator cards table 2.12 shows the modulator cards and associate...
Page 44: And E5714)
Installing the equipment page 2-20 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.6.10 satellite modulator if output (e5714 and e5740 if) if out (main) 75 Ω bnc socket provides an if output. Table 2.13: if out connector (main) item specification connector type bnc 75 Ω female ...
Page 45
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-21 st.Re.E10076.3 l-band out (main) 50 Ω sma female connector provides the main l-band output. Both models can provide a 10 mhz reference frequency output and the e5740 can also source +24 vdc at up to 500 ma to pow...
Page 46
Installing the equipment page 2-22 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 2.18: asi input item specification connector type 75 Ω bnc female type analogue connector designation asi in 1, asi in 2 pin-outs centre signal screen ground 2.6.12 ofdm modulator outputs (e5...
Page 47: 2.7 Powering
Installing the equipment reference guide: e57xx dsng and deng voyager encoder page 2-23 st.Re.E10076.3 2.7 powering up/down 2.7.1 before powering up before powering up the encoder, check that: 1. The unit has been installed in a suitable location. 2. The unit has been connected to external equipment...
Page 48: 2.8.2
Installing the equipment page 2-24 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2.8.2 from the front panel menus to access the ip address option from the front panel menus, press the ip address softkey in the remote control menu. Edit the ip address via the keypad and then pre...
Page 49: Contents
Reference guide: e57xx dsng and deng voyager encoder page 3-1 st.Re.E10076.3 chapter 3 3. Options and upgrades contents 3.1 what’s available........................................................ 3-3 3.1.1 option functions .......................................... 3-3 3.1.2 limitations on number o...
Page 50
Options and upgrades page 3-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.10.1 overview .....................................................3-22 3.10.2 assembly.....................................................3-23 rear panel ...............................................
Page 51: 3.1 What’S
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-3 st.Re.E10076.3 3.1 what’s available 3.1.1 option functions the basic encoder functionality can be enhanced with the inclusion of options, hardware and software. Each hardware option module consists of a horizontally m...
Page 52: 3.1.2
Options and upgrades page 3-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 3.2: software options marketing code name used in 1u used in 2u m2/eso2/nr noise reduction ✔ ✔ m2/eso2/pu performance upgrade/bit-rate ✔ ✔ m2/eso2/vbr vbr licence ✔ ✔ m2/eso2/422 4:2:2 ✔ ✔ m2/eso2...
Page 53: 3.1.4
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-5 st.Re.E10076.3 3.1.4 how to see which options are fitted/enabled the encoder has a number of hardware and software options (see table 3.1 and table 3.2). To see which are fitted/enabled refer to the build menu (see ch...
Page 54: 3.4
Options and upgrades page 3-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 the biss module (m2/edcom2/biss) comprises assembly s12284 and card s11484. Notes… 1. This option module is installed as a daughter card to the base board, with no external connectors and does not use a...
Page 55: 3.4.2 Assembly
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-7 st.Re.E10076.3 3.4.2 assembly rear panel note… the aes/ebu reference signal is provided for backwards compatibility only. When using e57xx encoders use the reference signal provided by the base board. Figure 3.1: addi...
Page 56
Options and upgrades page 3-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 3.4: audio in connector pin signal pin signal analogue digital analogue digital 1 left channel a (+) aes/ebu (a) (+) 9 left channel a (-) aes/ebu (a) (-) 2 not connected 10 right channel a (+) 3 r...
Page 57: 3.5
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-9 st.Re.E10076.3 3.5 remux option (m2/eom2/remux) 3.5.1 overview note… the m2/eom2/remux remux option module is supported by build version 2.2.0 and later. The remux option module is capable of accepting up to three sep...
Page 58: 3.5.3
Options and upgrades page 3-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 dvb asi in 1, 2 and 3 connectors a 75 Ω bnc connector provides an input to the unit. Table 3.5: dvb asi in connector pin signal centre signal screen ground note… when connecting the inputs, always star...
Page 59
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-11 st.Re.E10076.3 figure 3.3: block diagram – one stage of remultiplexing similarly, if two stages of remultiplexing are introduced, thirteen encoders can be combined, providing up to thirteen services in the remultiple...
Page 60: 3.5.4 Function
Options and upgrades page 3-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.5.4 function of remultiplexer it is the function of the remultiplexer to combine the locally generated host services with the externally supplied input services, connected via asi inputs to the rear ...
Page 61: 3.5.5 Using
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-13 st.Re.E10076.3 3.5.5 using the remultiplexer set the output bit-rate to the required value in the setup/mux menu. Connect transport streams that are to be combined (remultiplexed) with the host encoder’s services to ...
Page 62: 3.5.8
Options and upgrades page 3-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 the easiest way to configure the bit-rates to avoid overflow, is as follows: 1. Divide the 188 byte output bit-rate of the primary (master) remultiplexing unit, (this can be found in the setup/mux/remu...
Page 63: 3.6.2 Assembly
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-15 st.Re.E10076.3 3.6.2 assembly rear panel asi out a 75 Ω female bnc connector provides an asi output of the transport stream being decoded by the sd decoder. Note… if the 16qam demodulator is being used the asi out wi...
Page 64
Options and upgrades page 3-16 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 3.8: sdi video out connector item specification connector type 75 Ω bnc female connector designation sdi out pin-outs centre signal screen ground composite video output a 75 Ω female bnc connecto...
Page 65: 3.7
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-17 st.Re.E10076.3 rs-232/rs-422 data output a 9-way d-type socket provides the data outputs. Table 3.11: rs-232/rs-422 data output connector item specification connector type 9-way d-type socket connector designation rs...
Page 66: 3.7.2 Assembly
Options and upgrades page 3-18 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.7.2 assembly rear panel Ω if in a 75 Ω female bnc connector provides an if input. Table 3.12: if in connector item specification connector type 75 Ω bnc female connector designation if in pin-outs ce...
Page 67: 3.8
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-19 st.Re.E10076.3 3.8 16qam demodulator (m2/eom2/satdemod) 3.8.1 overview the module allows the encoder to receive and demodulate satellite transmissions that comply to en 300 421 (dvb-s), and en 301 210 (dvb-dsng). It ...
Page 68: 3.9.2 Assembly
Options and upgrades page 3-20 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 3.6: ip output protocol stack between one and seven mpeg-2 transport stream packets can be put in each udp packet. The data link layer is ethernet according to ieee 802.3/802.3u (auto-sensing 10...
Page 69
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-21 st.Re.E10076.3 rs-232 control a 3.5mm socket provides a debug interface. Note… this connector is for tandberg television use only. Asi out a 75 Ω female bnc connector provides an asi output. Note… this connector is n...
Page 70: And M2/eom2/comms/fxo)
Options and upgrades page 3-22 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.10 vocality card option (m2/eom2/comms/fxs and m2/eom2/comms/fxo) 3.10.1 overview the dsng communications card adds bi-directional telephone, data and ip interfaces to an e5740 encoder. There are two...
Page 71: 3.10.2 Assembly
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-23 st.Re.E10076.3 for details regarding configuring this card via the supervisor port refer to the dsng comms card documentation provided on the reference cd. 3.10.2 assembly rear panel figure 3.8: vocality card option ...
Page 72
Options and upgrades page 3-24 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 3.19: telephone/line connector 4-wire tie-line mode 2-wire fxs/fxo mode pin signal signal 1 mref 2 m 3 rxa 4 txrxa tip 5 txrxb ring 6 rxb 7 e 8 eref data connector a 15-way, d-type female connect...
Page 73
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-25 st.Re.E10076.3 table 3.21: supervisor connector pin signal 1 (tip) transmit (out) 2 (ring) receive {in) 3 (shield) ground link connector a 15-way, d-type female connector provides the rs-422 interface to the encoder ...
Page 74: Encoder
Options and upgrades page 3-26 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 encoder the dsng communications card requires an external cable to be fitted to connect it to the encoder. This cable is supplied with the option card. • the 15-way, d-type male labelled link should be...
Page 75: 3.11.3 Connector
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-27 st.Re.E10076.3 3.11.2 assembly (1u panel version shown) figure 3.10: general purpose interface m2/eom2/gpi 3.11.3 connector table 3.24: gpi connector item specification item specification connector type 15-way d-type...
Page 76: 3.12.1 Introduction
Options and upgrades page 3-28 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.12 triax option (m2/eom2/triax) 3.12.1 introduction this option is for the e5750 encoder only. The card is designed to work in conjunction with the cofdm modulator fitted to the e5750 encoder in orde...
Page 77: 3.13 Software
Options and upgrades reference guide: e57xx dsng and deng voyager encoder page 3-29 st.Re.E10076.3 3.13 software options 3.13.1 m2/eso2/nr this purchasable option upgrades the encoder to include noise reduction mode. Contact customer services for details. 3.13.2 m2/eso2/pu this purchasable option up...
Page 78: 3.13.12 M2/eso2/lsym
Options and upgrades page 3-30 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 3.13.12 m2/eso2/lsym this purchasable option allows an e5740 and an m2/eom2/qpskdemod, if fitted, to work at low symbol rates (300 ksym/s minimum). Contact customer services for details. 3.13.13 m2/eso...
Page 79: Contents
Reference guide: e57xx dsng and deng voyager encoder page 4-1 st.Re.E10076.3 chapter 4 4. Operating the equipment locally contents 4.1 introduction ............................................................... 4-9 4.2 establishing local control (1u)................................. 4-9 4.3 navigat...
Page 80
Operating the equipment locally page 4-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 logical channel option...............................4-23 4.7.4 remote control menu.................................4-23 overview .....................................................4-23 ip ...
Page 81
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-3 st.Re.E10076.3 afd location.............................................. 4-46 encoder type option.................................. 4-46 s/w release option ................................... 4-46 4.8.4 ve...
Page 82
Operating the equipment locally page 4-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 channel option ...........................................4-74 embedded 1-2 did option..........................4-74 embedded 3-4 did option..........................4-74 audio pid option ......
Page 83
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-5 st.Re.E10076.3 preset pwr norm option 15 .......................... 4-93 buc dc power option 15 ............................ 4-93 sat deliv freq option ................................. 4-93 sat orb pos opt...
Page 84
Operating the equipment locally page 4-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 lnb hi freq option...................................4-116 lnb switch freq option ...........................4-116 lnb supply ...............................................4-116 search range...
Page 85
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-7 st.Re.E10076.3 list of figures figure 4.1: 1u summary screen ................................................... 4-9 figure 4.2: 1u navigation keys and buttons............................... 4-10 figure 4.3...
Page 86
Operating the equipment locally page 4-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.87: hierarchy options..................................................... 4-82 table 4.88: fec (hp) and fec (lp) options ............................. 4-83 table 4.89: guard interval...
Page 87: 4.1 Introduction
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-9 st.Re.E10076.3 4.1 introduction the front panel display and keypad are used to configure, control and monitor the encoder. The control interface is a structured menu which gives access to the various option...
Page 88: 4.3.2
Operating the equipment locally page 4-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.2: 1u navigation keys and buttons note… the navigation keys are referred to as left, right, up and down, indicating the direction of the arrows. From the summary screen select the m...
Page 89: 4.3.4 Line
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-11 st.Re.E10076.3 for multiple choice entry • down scrolls down to next option • up scrolls up to previous option • right no action • left no action • enter accepts new setting • cancel leaves setting unchang...
Page 90: 4.4
Operating the equipment locally page 4-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.4 establishing local control (2u) 4.4.1 input monitor at power-on the encoder runs through a boot sequence (boot time with remux option module is approximately 90 seconds). An initial inpu...
Page 91: 4.4.4 Keyboard
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-13 st.Re.E10076.3 4.4.3 a(udio)/v(ideo) menu (2u) the a/v menu contains some basic video and audio options. They can all be changed with the exception of the audio input levels. These are only indicators of t...
Page 92: 4.5.2
Operating the equipment locally page 4-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.6: 2u keypad and display functions 4.5.2 how to use the keypad each key on the keypad has more than one inscription. One press of a key makes the number appear on the display screen...
Page 93: 4.5.3
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-15 st.Re.E10076.3 4.5.3 how to use the functions associated with softkeys the following display screens show the different functions associated with the options. Note… a black diagonal cross enclosed by a whi...
Page 94
Operating the equipment locally page 4-16 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.8: menu hierarchy – summary screen and advanced menus — active errors… — ignored errors… — error masks… — masked active errors — quit config menu operations menu from the input moni...
Page 95: 4.5.6
Operating the equipment locally reference guide: e57xx dsng and deng voyager encoder page 4-17 st.Re.E10076.3 4.5.6 summary screen and advanced menus see figure 4.8, for the top-level menu hierarchy. Access the advanced menu from the summary screen. The advanced menu provides options for configuring...
Page 96
Operating the equipment locally — system menu page 4-18 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.9: menu hierarchy – setup/system menu remote control menu menu options depend on syntax selected shaded options are showing status and cannot be changed. 1 some of the...
Page 97: 4.7.2
Operating the equipment locally — system menu service info menu (syntax = atsc) reference guide: e57xx dsng and deng voyager encoder page 4-19 st.Re.E10076.3 4.7.2 service info menu (syntax = atsc 1 ) overview this menu provides options for configuring the service information (si) parameters transmi...
Page 98
Operating the equipment locally — system menu service info menu (syntax = atsc) page 4-20 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 ext. Psip source option this option only applies if the si level has been set to on (ext. Psip). It specifies the remux input through which th...
Page 99: 4.7.3
Operating the equipment locally — system menu service info menu (syntax = atsc) reference guide: e57xx dsng and deng voyager encoder page 4-21 st.Re.E10076.3 note… this option is not displayed if the unit is set to generate psip externally or it is under mem control. Program paradigm option this opt...
Page 100
Operating the equipment locally — system menu service info menu (syntax = dvb) page 4-22 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 service name option this option allows the service name to be changed. The information is included in the sdt. Syntax option this enables the s...
Page 101: 4.7.4 Remote
Operating the equipment locally — system menu service info menu (syntax = dvb) reference guide: e57xx dsng and deng voyager encoder page 4-23 st.Re.E10076.3 service type option the service type identifies the type of service carried. The options are: analog tv, digital tv, digital radio, teletext, a...
Page 102
Operating the equipment locally — system menu remote control menu page 4-24 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 ip address option this option allows the ip address to be changed. Mac address option the mac address cannot be changed. Network mask option this option all...
Page 103
Operating the equipment locally — system menu remote control menu reference guide: e57xx dsng and deng voyager encoder page 4-25 st.Re.E10076.3 sntp server option this option sets the ip address of a simple network time protocol (sntp) server, which the encoder will then synchronise it’s clock to. I...
Page 104: 4.7.5 General
Operating the equipment locally — system menu general menu page 4-26 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.7.5 general menu overview the general menu provides options for configuring the general parameters of the encoder such as the time and date, screen savers, and f...
Page 105
Operating the equipment locally — system menu geneal menu reference guide: e57xx dsng and deng voyager encoder page 4-27 st.Re.E10076.3 table 4.8: screen saver options selected option description top level menu van service name off if no changes have been made to the encoder for five minutes (no sof...
Page 106: 4.7.6
Operating the equipment locally — system menu general menu page 4-28 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.11: fan control options selected option description auto (temp. Control) the fans are activated automatically when a defined temperature is reached. On the...
Page 107
Operating the equipment locally — system menu advanced menu reference guide: e57xx dsng and deng voyager encoder page 4-29 st.Re.E10076.3 if the control equipment is a tt7000 system manager, ensure that the auto lip sync option is turned on (see auto lip sync option on page 4-58). The tt7000 does no...
Page 108: 4.7.8
Operating the equipment locally — system menu advanced menu page 4-30 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 mbd. Service pids option this option is only available if the number of services is greater than one. The motherboard service pids option defines whether the pids...
Page 109
Operating the equipment locally — system menu advanced menu reference guide: e57xx dsng and deng voyager encoder page 4-31 st.Re.E10076.3 scramble option this option controls whether the service is in the clear (no scrambling) or the type of scrambling applied to it. Name option this option sets the...
Page 110: 4.8 Video
Operating the equipment locally — video menu: video source menu page 4-32 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.8 video menu 4.8.1 introduction the video menu is selected from the setup menu. This menu permits the selection of video parameters (see figure 4.10 for men...
Page 111
Operating the equipment locally — video menu: video source menu reference guide: e57xx dsng and deng voyager encoder page 4-33 st.Re.E10076.3 figure 4.10: menu hierarchy – setup/video menu only shown if the logo has previously been downloaded vbi in picture is only available when the profile/level i...
Page 112
Operating the equipment locally — video menu: video source menu page 4-34 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 input source select this allows the enabling or disabling of automatic frame rate detection. Table 4.16: inputsource select options selected option descriptio...
Page 113
Operating the equipment locally — video menu: video source menu reference guide: e57xx dsng and deng voyager encoder page 4-35 st.Re.E10076.3 background colour option this option defines the background colour for any on-screen messages generated by the encoder (e.G. By the ident test pattern). Cauti...
Page 114
Operating the equipment locally — video menu: video source menu page 4-36 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 noise reduction option 3 this option enables the noise reduction feature to be switched on (at different levels) or off. The feature can be used when the inco...
Page 115: 4.8.3
Operating the equipment locally — video menu: video source menu reference guide: e57xx dsng and deng voyager encoder page 4-37 st.Re.E10076.3 default 625 this sets the default for the 625 line standard. Table 4.23: default 625 options selected option description pal-b/g/h/i pal-d pal-m (jaimaca) pal...
Page 116
Operating the equipment locally — video menu: video encoder menu page 4-38 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.25: profile/level options selected option description mp@ml main profile @ main level. Typically used in 4:2:0 direct to home. 422p@ml 4:2:2 profile ...
Page 117
Operating the equipment locally — video menu: video encoder menu reference guide: e57xx dsng and deng voyager encoder page 4-39 st.Re.E10076.3 seamless 1 mode can use video bit-rates from 0.8 mbit/s to 10 mbit/s, with the actual limits depending on video standard and resolution. This would be used f...
Page 118
Operating the equipment locally — video menu: video encoder menu page 4-40 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 delay option this option indicates the current video delay. It is for status only and cannot be changed. Vbr mode option it is possible to operate the encode...
Page 119
Operating the equipment locally — video menu: video encoder menu reference guide: e57xx dsng and deng voyager encoder page 4-41 st.Re.E10076.3 the required picture quality is set in the same menu by the vbr target quality item. When running in vbr mode the two top-level status screens show the curre...
Page 120
Operating the equipment locally — video menu: video encoder menu page 4-42 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 aspect ratio option this option does not affect the image processing. Table 4.29: aspect ratio options selected option description 1, 0 video image is encode...
Page 121
Operating the equipment locally — video menu: video encoder menu reference guide: e57xx dsng and deng voyager encoder page 4-43 st.Re.E10076.3 no input or present but no video index data off encoder setting not present encoder setting 0 (active region is the same as encoded frame) stays at last aspe...
Page 122
Operating the equipment locally — video menu: video encoder menu page 4-44 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 long gops option note… only available if m2/eso2/pu has been purchased. This is used to enable or disable the use of gop structures that are longer than 500 ...
Page 123
Operating the equipment locally — video menu: video encoder menu reference guide: e57xx dsng and deng voyager encoder page 4-45 st.Re.E10076.3 the option should be switched on if the video material originated on film and has been converted from the 24 frames per second film rate to the 29.97 frames ...
Page 124: 4.8.4
Operating the equipment locally — video menu: video encoder menu page 4-46 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 insert vbv delay option if this option is turned on the encoder will insert vbv_delay values into the picture header. This is required by some older set-top ...
Page 125
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu reference guide: e57xx dsng and deng voyager encoder page 4-47 st.Re.E10076.3 teletext tag option this option sets the component tag for the teletext stream. The valid range is 0 to 255. Vitc on pes option extraction...
Page 126
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu page 4-48 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 vbi in picture option notes… 1. The vbi in picture option is only accessible if the selected video profile/level is 422p@ml 6 . 2. Vbi in ...
Page 127
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu reference guide: e57xx dsng and deng voyager encoder page 4-49 st.Re.E10076.3 blank line 23 option this option controls the blanking of line 23. The options are off or whole line blanked. The option is provided to en...
Page 128
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu page 4-50 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 notes… 1. Vitc is carried as timecode in the video stream rather than as a separate pes stream. If vitc is not present, a locally generate...
Page 129
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu reference guide: e57xx dsng and deng voyager encoder page 4-51 st.Re.E10076.3 field 1 field 2 6 teletext system b or inverted teletext, vitc, video index, closed caption, wide screen signalling (wss), off, video prog...
Page 130
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu page 4-52 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 vbi menu (29.97 hz frame rate) vitc on pes option extraction of vitc data from line 16 or 22 for 625-line systems (ebu definitions) or lin...
Page 131
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu reference guide: e57xx dsng and deng voyager encoder page 4-53 st.Re.E10076.3 closed caption option this option controls the extraction and processing of closed caption data by the encoder. Closed caption data can be...
Page 132
Operating the equipment locally — video menu: vertical blanking interval (vbi) menu page 4-54 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 auto detect vitc option if this option is enabled the encoder automatically detects the presence of vertical interval time code (vitc) dat...
Page 133: 4.9 Audio
Operating the equipment locally — audio menu: mpeg layer 2 reference guide: e57xx dsng and deng voyager encoder page 4-55 st.Re.E10076.3 4.9 audio menu 4.9.1 overview the encoder can process two stereo pairs as standard, but with the addition of audio option cards it can process more. The control me...
Page 134
Operating the equipment locally — audio menu: mpeg layer 2 page 4-56 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.13: menu hierarchy – setup/audio menu — source — coding standard — input level l — input level r 6 — audio bit-rate — coding mode — auto lip sync — lip sy...
Page 135
Operating the equipment locally — audio menu: mpeg layer 2 reference guide: e57xx dsng and deng voyager encoder page 4-57 st.Re.E10076.3 input level l option this indicates the input level of the left audio channel. It is for status only and cannot be changed. Input level r option this indicates the...
Page 136
Operating the equipment locally — audio menu: mpeg layer 2 page 4-58 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.41: coding mode options (mpeg-2) selected option description mono left single channel mono audio, encoding the left channel. Mono right single channel mono...
Page 137
Operating the equipment locally — audio menu: mpeg layer 2 reference guide: e57xx dsng and deng voyager encoder page 4-59 st.Re.E10076.3 embedded 1-2 did option this option defines the did to be de-embedded to obtain the audio source for sdi embedded 1 and sdi embedded 2. If this is set to 1024, the...
Page 138
Operating the equipment locally — audio menu: mpeg layer 2 page 4-60 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 hardware release option this option indicates the hardware version of this audio encode channel. It is for status only and cannot be changed. Software release opti...
Page 139: 4.9.3
Operating the equipment locally — audio menu: mpeg layer 2 reference guide: e57xx dsng and deng voyager encoder page 4-61 st.Re.E10076.3 for a digital audio input, pre-emphasis detection is typically achieved by monitoring the pre-emphasis flags within the channel status data of the incoming digital...
Page 140
Operating the equipment locally — audio menu: dolby digital (ac-3) menu page 4-62 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.48: audio bit-rate options (dolby digital (ac-3)) available settings dolby digital 1/0(c) 2/0(l,r) 32 kbit/s 8 8 48 kbit/s 8 8 56 kbit/s 9 8 6...
Page 141
Operating the equipment locally — audio menu: dolby digital (ac-3) menu reference guide: e57xx dsng and deng voyager encoder page 4-63 st.Re.E10076.3 lip sync offset option this option is only available if the auto lip sync option is set to on. It allows a fixed delay to be applied to the audio in a...
Page 142
Operating the equipment locally — audio menu: dolby digital (ac-3) menu page 4-64 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 language option this enables the language of the audio channel to be set. Bit-stream mode option this option sets the bit-stream mode that is signalle...
Page 143
Operating the equipment locally — audio menu: dolby digital (ac-3) menu reference guide: e57xx dsng and deng voyager encoder page 4-65 st.Re.E10076.3 production info option this option indicates whether the mixing level and room type parameters exist within the bit-stream. Mixing level option this o...
Page 144
Operating the equipment locally — audio menu: dolby digital (ac-3) menu page 4-66 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.58: dynamic range options selected option description none program reproduction with the original dynamic range. Film standard film light musi...
Page 145
Operating the equipment locally — audio menu: dolby digital (ac-3) menu reference guide: e57xx dsng and deng voyager encoder page 4-67 st.Re.E10076.3 embedded 1-2 did option this option defines the did to be de-embedded to obtain the audio source for sdi embedded 1 and sdi embedded 2. If this is set...
Page 146: 4.9.4
Operating the equipment locally — audio menu: dolby (ac-3) pass-thru, dolby e pass-thru and dts pass-thru menu page 4-68 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.9.4 audio (dolby (ac-3) pass-thru, dolby e pass-thru and dts pass-thru) menu source option this option define...
Page 147
Operating the equipment locally — audio menu: dolby (ac-3) pass-thru, dolby e pass-thru and dts pass-thru menu reference guide: e57xx dsng and deng voyager encoder page 4-69 st.Re.E10076.3 lip sync offset option this option is only available if the auto lip sync option is set to on. It allows a fixe...
Page 148
Operating the equipment locally — audio menu: dolby (ac-3) pass-thru, dolby e pass-thru and dts pass-thru menu page 4-70 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.65: smpte 302m standard options selected option description 1998 standard refers to the 1998 smpte 302m...
Page 149: 4.9.5
Operating the equipment locally — audio menu: dolby (ac-3) pass-thru, dolby e pass-thru and dts pass-thru menu reference guide: e57xx dsng and deng voyager encoder page 4-71 st.Re.E10076.3 pcr on audio pid option this option controls whether pcr should be signalled on the audio pid. This may be nece...
Page 150
Operating the equipment locally — audio menu: linear pcm menu page 4-72 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 coding standard option this option controls the audio coding standard. The options available in the audio menu are dependent on the coding standard selected. Ta...
Page 151
Operating the equipment locally — audio menu: linear pcm menu reference guide: e57xx dsng and deng voyager encoder page 4-73 st.Re.E10076.3 table 4.71: lip sync offset options valid input range description min: -50 max: 50 lip sync offset in milliseconds. Audio delay option this option is only avail...
Page 152
Operating the equipment locally — audio menu: linear pcm menu page 4-74 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 smpte 302m standard option smpte 302m defines the mapping of aes3 data in to an mpeg-2 transport stream. Problems may be experienced with some receivers if the ...
Page 153: 4.9.6
Operating the equipment locally — audio menu: linear pcm menu reference guide: e57xx dsng and deng voyager encoder page 4-75 st.Re.E10076.3 component tag option this item defines the optional component tag to be assigned to this audio stream. Pcr on audio pid option this option controls whether pcr ...
Page 154
Operating the equipment locally — data menu page 4-76 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.14: menu hierarchy – setup/data menu 4.10.2 data a - rs232 menu encoding option this option allows the protocol for rs-232 asynchronous data carriage to be chosen, or to...
Page 155
Operating the equipment locally — data menu reference guide: e57xx dsng and deng voyager encoder page 4-77 st.Re.E10076.3 rs232 pid option this option is used for entering or updating data pids. To be dvb compliant, pids below 32 are reserved. Therefore pids 32 to 8191 are available for use. In the ...
Page 156: 4.11 Output
Operating the equipment locally — data menu page 4-78 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 bit-rate option this option enables the bit-rate of the rs-422 synchronous data channel to be set. Table 4.80: bit-rate options selected option description settings cycle from 56...
Page 157: 4.11.2 Output
Operating the equipment locally — output menu reference guide: e57xx dsng and deng voyager encoder page 4-79 st.Re.E10076.3 4.11.2 output format option access the output format option from the output menu. The menus available depend upon which option cards are fitted to the unit. If the output forma...
Page 158
Operating the equipment locally — descriptor type = terrestrial menu page 4-80 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 7 figure 4.15: menu hierarchy – setup/output menu . Setup menu satellite modulator menu descriptor type menu options depend on descriptor type selected c...
Page 159
Operating the equipment locally — output menu reference guide: e57xx dsng and deng voyager encoder page 4-81 st.Re.E10076.3 4.11.5 descriptor type = terrestrial band plan option access the band plan option from the delivery descriptor menu. Once a country has been selected then the required channel ...
Page 160
Operating the equipment locally — output menu: descriptor type = terrestrial page 4-82 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.84: frequency options selected option description min: 0.0001 mhz max: 42949.6729 mhz step size: 0.0001 mhz carrier frequency of transmit...
Page 161
Operating the equipment locally — output menu: descriptor type = terrestrial reference guide: e57xx dsng and deng voyager encoder page 4-83 st.Re.E10076.3 fec (hp) and fec (lp) options access the fec (hp) or the fec (lp) option from the delivery descriptor menu . These screens enable the inner fec s...
Page 162
Operating the equipment locally — output menu: descriptor type = terrestrial page 4-84 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.90: carriers options selected option description 2k mode terrestrial transmitter uses 2k transmission mode (2k carriers in an ofdm frame)...
Page 163
Operating the equipment locally — output menu: descriptor type = cable reference guide: e57xx dsng and deng voyager encoder page 4-85 st.Re.E10076.3 fec (inner) option access the fec (inner) option from the delivery descriptor menu. This screen enables the inner fec rate used by the cable channel to...
Page 164
Operating the equipment locally — output menu: descriptor type = satellite page 4-86 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 fec (inner) option access the fec (inner) option from the delivery descriptor menu. This screen enables the inner fec rate used by the satellite tr...
Page 165
Operating the equipment locally — output menu: output format = satellite modulator (if output) reference guide: e57xx dsng and deng voyager encoder page 4-87 st.Re.E10076.3 4.11.8 output format = satellite modulator (if output) ts input source this option determines the source of the transport strea...
Page 166
Operating the equipment locally — output menu: output format = satellite modulator (if output) page 4-88 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.103: modulation type options selected option description bpsk satellite modulator uses bpsk modulation. Qpsk satellite ...
Page 167
Operating the equipment locally — output menu: output format = satellite modulator (if output) reference guide: e57xx dsng and deng voyager encoder page 4-89 st.Re.E10076.3 roll off factor option the roll off factor option is to do with the bandwidth of the modulated output and how quickly the outpu...
Page 168
Operating the equipment locally — output menu: output format = satellite modulator (if output) page 4-90 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 buc dc power option caution… the modulator provides dc power to drive an up-converter. Do not connect equipment to the main out...
Page 169: (L-Band Output)
Operating the equipment locally — output menu: output format = satellite modulator (if output) reference guide: e57xx dsng and deng voyager encoder page 4-91 st.Re.E10076.3 table 4.112: polarisation options selected option description linear - horizontal satellite transponder uses linear horizontal ...
Page 170
Operating the equipment locally — output menu: output format = satellite modulator (if output) page 4-92 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.113: ts input source options selected option description backplane asi1 asi2 only available in the e5740. Rate adaptati...
Page 171
Operating the equipment locally — output menu: output format = satellite modulator (l-band output) reference guide: e57xx dsng and deng voyager encoder page 4-93 st.Re.E10076.3 roll off factor option in the l-band option, only 35% is allowed for qpsk and bpsk. Refer to roll off factor option on page...
Page 172
Operating the equipment locally — output menu: output format = satellite modulator (l-band output) page 4-94 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 sat orb pos option refer to sat orb pos option on page 4-90 for details. Sat west/east option refer to sat west/east option...
Page 173
Operating the equipment locally — output menu: output format = ofdm modulator reference guide: e57xx dsng and deng voyager encoder page 4-95 st.Re.E10076.3 guard interval option access the guard interval option from the ofdm modulator menu . Table 4.118: guard interval options selected option descri...
Page 174
Operating the equipment locally — output menu: output format = ofdm modulator page 4-96 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.122: centre frequency options valid input range description min: 0 mhz max: 4294.967295 mhz if output frequency the if output frequency ...
Page 175
Operating the equipment locally — mux menu reference guide: e57xx dsng and deng voyager encoder page 4-97 st.Re.E10076.3 this is the ip address to which the video stream should be sent. It can either be a unicast ip address or it can be a class d multicast address (224.0.0.1-239.255.255.255). Choosi...
Page 176: 4.12 Mux
Operating the equipment locally — output format = ip streamer page 4-98 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 this is the time-to-live setting as specified in rfc-791. The time-to-live setting is decremented by one for each router hop the ip frame does. When 0 (zero) is...
Page 177
Operating the equipment locally — mux menu reference guide: e57xx dsng and deng voyager encoder page 4-99 st.Re.E10076.3 figure 4.16: menu hierarchy – setup/mux menu (dvb) — output — source (bnc) — name (in) — name out — service prov (in) — service id (out) — logical channel — ca input — biss key co...
Page 178
Operating the equipment locally — mux menu page 4-100 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 4.17: menu hierarchy – setup/mux menu (atsc) — output — source (bnc) — short name in — short name out — name in — name out — program number (out) — major channel — minor c...
Page 179: 4.12.4 Packet
Operating the equipment locally — mux menu reference guide: e57xx dsng and deng voyager encoder page 4-101 st.Re.E10076.3 4.12.4 packet length option this option enables the packet length to be set. Table 4.123: packet length options selected option description 188 bytes uses 188 byte packet format....
Page 180: 4.12.8 Pcr
Operating the equipment locally — mux menu page 4-102 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.126: clock options selected option description local oscillator the system clock is derived from the local oscillator. Hsync (external) the system clock is locked to the ...
Page 181
Operating the equipment locally — mux menu reference guide: e57xx dsng and deng voyager encoder page 4-103 st.Re.E10076.3 table 4.128: scramble options (ras) selected option description off encoder output is not scrambled. Ras (fixed 1) encoder output is scrambled using the fixed ras key assigned by...
Page 182
Operating the equipment locally — mux menu page 4-104 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 scramble option access the scramble option from the mux menu. This enables security scrambling of the encoder transmission to be switched on or off. Note… if the scrambling is sw...
Page 183: 4.13 Remux
Operating the equipment locally — mux menu reference guide: e57xx dsng and deng voyager encoder page 4-105 st.Re.E10076.3 biss-e injected id option access the biss-e injected id option from the mux menu. This is only used with biss-e and is an identifier for the unit, comprising a 56-bit hexadecimal...
Page 184
Operating the equipment locally — mux menu: remux menu (option) page 4-106 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.131: pid remap options selected option description update pids from i/ps in this mode, only changes at any of the remux inputs (e.G. Pid change, new ...
Page 185: 4.13.4 1.Service/2.Service
Operating the equipment locally — mux menu: remux menu (option) reference guide: e57xx dsng and deng voyager encoder page 4-107 st.Re.E10076.3 4.13.4 1.Service/2.Service menu output option this option enables the output to be set. Table 4.132: output options selected option description off the servi...
Page 186
Operating the equipment locally — mux menu: remux menu (option) page 4-108 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 name out option this option allows the service output name to be changed. Service prov (in) option note… this option is only shown on an incoming service men...
Page 187
Operating the equipment locally — mux menu: remux menu (option) reference guide: e57xx dsng and deng voyager encoder page 4-109 st.Re.E10076.3 this option enables the minor channel to be specified. Logical channel option this option enables a number to be given to the logical channel. Ca input optio...
Page 188
Operating the equipment locally — mux menu: remux menu (option) page 4-110 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 4.137: pcr pid options selected option description min: 1 max: 8190 (1ffeh) step size: 1 video option note… this option is status only for the host enc...
Page 189
Operating the equipment locally — mux menu: remux menu (option) reference guide: e57xx dsng and deng voyager encoder page 4-111 st.Re.E10076.3 audio (type of audio) option notes… 1. This option is status only for the host encoder but can be changed for incoming services. 2. The option could be audio...
Page 190: 4.14 Ird
Operating the equipment locally — mux menu: remux menu (option) page 4-112 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.14 ird menu 4.14.1 overview the ird menu is selected from the setup menu. The menu controls the internal receiver decoder (ird), if it is fitted. The ird c...
Page 191
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-113 st.Re.E10076.3 setup menu ird menu ird mode ird ts source ird demod (if fitted).... Service list.... Ird video.... Ird audio1.... Ird audio2.... Ird vbi.... Ird ca.... Ird data.... Ird system s...
Page 192: 4.14.4 Ird
Operating the equipment locally — ird menu page 4-114 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.14.3 ird ts source option access the ird ts source option from the ird menu . Table 4.145: ird ts source options selected option description ird demod the ird will decode the t...
Page 193
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-115 st.Re.E10076.3 polarisation option access the polarisation option from the ird demod menu . Table 4.148: polarisation options selected option description horizontal if lnb power is enabled, out...
Page 194
Operating the equipment locally — ird menu page 4-116 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 lnb hi freq option access the lnb hi freq option from the ird demod menu . This value should be set to the lnb’s higher local oscillator frequency. Lnb switch freq option access ...
Page 195: 4.14.5 Service List Menu
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-117 st.Re.E10076.3 4.14.5 service list menu access the service list menu from the ird menu. This lists all the services found in the current transport stream and allows the user to select which one...
Page 196
Operating the equipment locally — ird menu page 4-118 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 625 line composite option access the 625 line composite option from the ird video menu . Table 4.158: 625 line composite options selected option description 625 pal i the composi...
Page 197
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-119 st.Re.E10076.3 table 4.162: embedded audio mode options selected option description no audio no audio is embedded in the sdi output. Audio 1 only audio channel 1 is embedded in the sdi output. ...
Page 198
Operating the equipment locally — ird menu page 4-120 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 default language option access the default language option from the ird audio menu . If a service contains more than one audio stream, the decoder defaults to the first audio str...
Page 199: 4.14.8 Ird
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-121 st.Re.E10076.3 left sys clip option access the left sys clip option from the ird audio menu . This sets the audio clip level of the left channel between 6 dbm and 18 dbm. Right sys clip option ...
Page 200: 4.14.9 Ird Vbi Menu
Operating the equipment locally — ird menu page 4-122 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.14.9 ird vbi menu vits enable option access the vits enable option from the ird vbi menu . Table 4.168: vits enable options selected option description disabled vits test signa...
Page 201: 4.14.10 Ird Data Menu
Operating the equipment locally — ird menu reference guide: e57xx dsng and deng voyager encoder page 4-123 st.Re.E10076.3 4.14.10 ird data menu async stream option access the async stream option from the ird data menu . This is used to select the asynchronous data stream to be decoded, from those pr...
Page 202: 4.15 Vocality
Operating the equipment locally — ird menu page 4-124 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.14.11 ird system status menu the ird system status menu has a number of options which are status only and cannot be changed: • ts • network name • network id • services • curre...
Page 203: 4.16.1 Option
Operating the equipment locally — digital programme insertion (dpi) menu reference guide: e57xx dsng and deng voyager encoder page 4-125 st.Re.E10076.3 4.16 digital programme insertion (dpi) menu 4.16.1 option availability this option is only available from the systems menu when the m2/eso2/scte35 s...
Page 204
Operating the equipment locally — digital programme insertion (dpi) menu page 4-126 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 notes… 1. Some of the options may be different or unavailable in other dpi modes. 2. The stream carrying the splice information is referenced in pmt...
Page 205: 4.17 Errors Menu
Operating the equipment locally — digital programme insertion (dpi) menu reference guide: e57xx dsng and deng voyager encoder page 4-127 st.Re.E10076.3 4.17 errors menu 4.17.1 overview from the 2u encoder the errors menu can be selected from the advanced menu . From the 1u encoder the errors menu ca...
Page 206: 4.18 Diagnostics Menu
Operating the equipment locally — configs menu page 4-128 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 active errors error masks.... Quit error masks menu errors menu refer to annex h, error messages for details of all the error messages. Figure 4.20: menu hierarchy – error ma...
Page 207: 4.19 Configs Menu
Operating the equipment locally — errors menu / diagnostics menu reference guide: e57xx dsng and deng voyager encoder page 4-129 st.Re.E10076.3 4.19 configs menu 4.19.1 accessing the menu access the configs menu from the summary screen or from the advanced menu . 4.19.2 overview the encoder has a se...
Page 208: 4.19.4 User
Operating the equipment locally — configs menu page 4-130 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.19.4 user configurations configurations loaded into the user flash become user configurations. Any one of the user configurations can be loaded as an active configuration (...
Page 209
Operating the equipment locally — configs menu reference guide: e57xx dsng and deng voyager encoder page 4-131 st.Re.E10076.3 4.19.8 quick configuration from the summary screen the sixteen predefined user configurations are a quick and easy way to configure the encoder without having to enter indivi...
Page 210
Operating the equipment locally — configs menu page 4-132 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 4.19.12 store configs in backup option this enables the 16 user configurations to be stored in the backup, and may be password protected. Access the store configs in backup f...
Page 211: Contents
Reference guide: e57xx dsng and deng voyager encoder page 5-1 st.Re.E10076.3 chapter 5 5. Web browser interface contents 5.1 introduction ............................................................... 5-3 5.2 how to set up internet explorer for the web browser interface................................
Page 212
Web browser interface page 5-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 213: 5.1 Introduction
Web browser interface reference guide: e57xx dsng and deng voyager encoder page 5-3 st.Re.E10076.3 5.1 introduction there is a range of diagnostic and other utilities that can be accessed via a web browser, such as internet explorer. Before these can be accessed it is important to ensure that the in...
Page 214
Web browser interface page 5-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 5.2: settings dialog box 4. For check for newer versions of stored pages, select every visit to the page or any changes made to the pages will not be displayed. Click ok to save the changes and ...
Page 215
Web browser interface reference guide: e57xx dsng and deng voyager encoder page 5-5 st.Re.E10076.3 6. Click lan settings to open the local area network (lan) settings dialog box (see figure 5.4). Figure 5.4: local area network (lan) settings dialog box 7. Click advanced to open the proxy settings di...
Page 216: 5.3
Web browser interface page 5-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 9. Click ok as many times as necessary to close all dialog boxes until only the internet explorer window is open. For internet explorer version 4 the same selections must be made, but the process start...
Page 217
Web browser interface reference guide: e57xx dsng and deng voyager encoder page 5-7 st.Re.E10076.3 • engineering symbol rate calculator the modulation help allows you to see the difference that various parameters have upon the symbol rate and bandwidth. Ofdm bit-rate calculator the bit-ratecalculato...
Page 218: 5.4 Fault
Web browser interface page 5-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 snmp mib this option is password protected. It allows the simple network management protocol (snmp) management information base (mib 1 ) files to be downloaded from the encoder to the pc. The password ...
Page 219: Contents
Reference guide: e57xx dsng and deng voyager encoder page 6-1 st.Re.E10076.3 chapter 6 6. Preventive maintenance and fault-finding contents 6.1 introduction ............................................................... 6-3 6.2 preventive maintenance............................................ 6-3 ...
Page 220
Preventive maintenance and fault-finding page 6-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 221: 6.1 Introduction
Preventive maintenance and fault-finding reference guide: e57xx dsng and deng voyager encoder page 6-3 st.Re.E10076.3 6.1 introduction this chapter provides the schedules and instructions, where applicable, for routine inspection, cleaning and maintenance of the equipment which should be performed b...
Page 222: 6.3
Preventive maintenance and fault-finding page 6-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 replacement parts when replacement parts are required, be sure the service technician has used parts specified by the manufacturer or which have the same characteristics as the origi...
Page 223: 6.4
Preventive maintenance and fault-finding reference guide: e57xx dsng and deng voyager encoder page 6-5 st.Re.E10076.3 6.4 errors and diagnostics menus – when to use them 6.4.1 error messages figure 6.1: finding the errors menu investigate any run-time errors by pressing the active errors softkey in ...
Page 224
Preventive maintenance and fault-finding page 6-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure 6.2: finding the diagnostics menu lcd display test press the lcd display softkey to access the option and then press any key to cycle through the test patterns and to return t...
Page 225: 6.5 Fault-Finding
Preventive maintenance and fault-finding reference guide: e57xx dsng and deng voyager encoder page 6-7 st.Re.E10076.3 buzzer test press the buzzer softkey to access the option which immediately causes a buzzer to sound. Press any key (except the quit softkey) to turn the buzzer off. Press the quit s...
Page 226: 6.5.3
Preventive maintenance and fault-finding page 6-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 2. Confirm that the equipment hardware configuration is suitable for the purpose and has been correctly installed and connected (see chapter 2, installing the equipment). 3. Confirm ...
Page 227: 6.5.4 Video
Preventive maintenance and fault-finding reference guide: e57xx dsng and deng voyager encoder page 6-9 st.Re.E10076.3 figure 6.3: orientation of fuse carrier if the replacement fuse also blows, do not continue. Disconnect the equipment and contact customer services for advice. 6.5.4 video fault-find...
Page 228: 6.5.5 Audio
Preventive maintenance and fault-finding page 6-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 6.5.5 audio fault-finding if having problems when using the dolby e pass-thru or dts pass-thru coding modes then refer to annex g, audio modes, for information about using this mode...
Page 229: 6.8
Preventive maintenance and fault-finding reference guide: e57xx dsng and deng voyager encoder page 6-11 st.Re.E10076.3 6.8 power supply problems/green led on front panel unlit 6.8.1 symptoms warning... Do not attempt to service the power supply unit as opening or removing covers may expose dangerous...
Page 230: 6.9
Preventive maintenance and fault-finding page 6-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table 6.4: fans not working/overheating step action if result of action is yes… if result of action is no… 1 check fan rotation. Inspect the fans located at the sides of the enclosu...
Page 231
Reference guide: e57xx dsng and deng voyager encoder page a-1 st.Re.E10076.3 annex a a. Glossary the following list covers most of the abbreviations, acronyms and terms as used in tandberg television limited manuals. All terms may not be included in this manual. µm micrometre (former name - micron):...
Page 232
Glossary page a-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b3zs bipolar with three zero substitution: a method of eliminating long zero strings in a transmission. It is used to ensure a sufficient number of transitions to maintain system synchronisation when the user data ...
Page 233
Glossary reference guide: e57xx dsng and deng voyager encoder page a-3 st.Re.E10076.3 compression reduction in the number of bits used to represent the same information. For the purposes of a broadcast system, it is the process of reducing digital picture information by discarding redundant portions...
Page 234
Glossary page a-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 dvb-pi dvb-professional interfaces: ttv lan search shows – dvb physical interfaces earth technical earth: ensures that all equipment chassis within a rack are at the same potential, usually by connecting a wire bet...
Page 235
Glossary reference guide: e57xx dsng and deng voyager encoder page a-5 st.Re.E10076.3 icam integrated conditional access module: embedded in the ird and responsible for descrambling, plus packet filtering and reception. It also contains the physical interface to the subscriber’s viewing card. Iec in...
Page 236
Glossary page a-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 lo local oscillator. Lsb least significant bit. Luminance the television signal representing brightness, or the amount of light at any point in a picture. The y in yc r c b. Lvds low voltage differential signal: lv...
Page 237
Glossary reference guide: e57xx dsng and deng voyager encoder page a-7 st.Re.E10076.3 nm nanometre: a unit of length equal to one thousand millionth (10 -9 ) of a metre. Ntsc national television systems committee: the group, which developed analogue standards used in television broadcast systems in ...
Page 238
Glossary page a-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 ppv pay per view: a system of payment for viewing services based on a usage / event basis rather than on on-going subscription. Subscribers must purchase viewing rights for each ppv event that they wish to view. Pp...
Page 239
Glossary reference guide: e57xx dsng and deng voyager encoder page a-9 st.Re.E10076.3 stb set-top box: a box that sits on top of a television set and is the interface between the home television and the cable tv company. New technologies evolving for set-top boxes are video-on-demand, video games, e...
Page 240
Glossary page a-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 transport stream packet header a data structure used to convey information about the transport stream payload. Ts transport stream. Tsdt transport stream descriptor table: a component of the mpeg-2 psi data. This ...
Page 241: Contents
Reference guide: e57xx dsng and deng voyager encoder page b-1 st.Re.E10076.3 annex b b. Technical specification contents b.1 inputs b-3 b.1.1 video ............................................................B-3 sdi................................................................B-3 h sync .............
Page 242
Technical specification page b-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.10.4 m2/eom2/qpskdemod, qpsk demodulator card option .......................... B-31 b.10.5 m2/eom2/satdemod, 16qam demodulator card option .......................... B-32 b.10.6 m2/eom2/ip, ip out...
Page 243: B.1 Inputs
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-3 st.Re.E10076.3 b.1 inputs b.1.1 video sdi table b.1: serial digital video specification item specification safety status selv connector designation sdi in connector type 75 Ω bnc female socket input standard (uk/ec...
Page 244
Technical specification page b-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 analogue video specification table b.3: analogue video specification item specification analogue input 625 line composite pal-b, -d, -g, -h, -i 525 line composite ntsc-m, pal-m as specified in itu-r ...
Page 245
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-5 st.Re.E10076.3 pal video performance figures table b.5: pal system video performance figures pattern item specification input return loss 30 db vits line 17 bar amplitude ref (bp) 700 mv ± 7 mv vits line 17 jitter ...
Page 246
Technical specification page b-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 pattern item specification 100% luma ramp luma noise weighted filters: tilt null, unified weighting, 5 mhz lpf, fsc trap, 100 khz hp ≤ -60 db 5-step staircase - modulated differential gain ±1.5% 5-st...
Page 247: B.1.2 Audio
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-7 st.Re.E10076.3 b.1.2 audio analogue and digital audio table b.9: analogue and digital audio specification item specification safety status selv connector designation audio in connector type 15-way, d-type male conn...
Page 248
Technical specification page b-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table b.10: musicam analogue test specification item specification set-up of alteia receiver audio format mpeg output analogue clip level 18 db set-up of audio encoder input analogue clip level 18 db...
Page 249
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-9 st.Re.E10076.3 item specification 315 hz ±2° 1 khz ±2° 6.3 khz ±2° 10 khz ±2° 15 khz ±2° embedded audio (via sdi) audio embedded on the serial digital interface can also be extracted. Up to four stereo pairs of aud...
Page 250: B.1.3 Rs-232
Technical specification page b-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 dolby digital audio encoding bit-rates table b.13: dolby digital audio encoding bit-rates bit-rate (kbit/s) single channel mono (1/0) dual channel stereo (2/0) 56 ✓ - 64 ✓ - 80 ✓ - 96 ✓ ✓ 112 ✓ ✓ 12...
Page 251: B.1.4 Rs-422
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-11 st.Re.E10076.3 b.1.4 rs-422 data this provides an rs-422 synchronous, serial communications data input interface. Table b.15: rs-422 data specification item specification safety status selv type itu-t v.11 (rs-422...
Page 252: B.1.6
Technical specification page b-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.1.6 l-band input (1u, e5714-lband/2u, e5740-lband) this input provides a carrier combining facility for summing an externally generated carrier into the l-band output. Table b.17: l-band in specif...
Page 253: B.3 Outputs
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-13 st.Re.E10076.3 b.3 outputs b.3.1 if outputs (1u, e5714) table b.20 parameters are with the s12376 card fitted. Table b.20: if out main specification (1u, e5714) item specification safety status: selv connector des...
Page 254
Technical specification page b-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table b.21: if monitor output specification (1u, e5714) item specification safety status: selv connector designation: if out monitor connector type: bnc, female 75 Ω this connector is normally dedic...
Page 255: B.3.2
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-15 st.Re.E10076.3 b.3.2 if outputs (e5740-if) if out (main) table b.22 parameters are with the s13716 card fitted. Table b.22: if out main specification (e5740-if) item specification safety status: selv connector typ...
Page 256: B.3.3
Technical specification page b-16 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 if out monitor table b.23: if out monitor specification (e5740-if) item specification safety status: selv connector type: bnc female 75 Ω connector designation: if out monitor output impedance: 75 Ω...
Page 257
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-17 st.Re.E10076.3 item specification (modulated carrier) excluding the frequency range of the wanted signal (equal to ±1.06 x symbol rate about the carrier frequency, as defined by the spectrum mask figure a.1 in en ...
Page 258: B.3.4
Technical specification page b-18 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 item specification short-circuit current: short-circuit duration: indefinite (automatic shutdown after approx. 2s) b.3.4 l-band outputs (1u e5714-lband) table b.28 parameters with s13719 2/3 width c...
Page 259: B.3.5
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-19 st.Re.E10076.3 table b.29: l-band monitor output specification (e5714-lband) item specification safety status: selv connector type: f-type female connector designation: l-band out monitor output impedance: 75 Ω ou...
Page 260: B.3.6
Technical specification page b-20 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table b.32: ofdm if out 2 specification (e5750) item specification safety status: selv connector type: bnc female connector designation: if out 2 output impedance: 75 Ω output power: - 10 db relativ...
Page 261: B.4
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-21 st.Re.E10076.3 b.4 control and monitoring b.4.1 remote control - ethernet 1 and 2 table b.34: ethernet specification item specification safety status selv connector designation ethernet#1 and ethernet#2 connector ...
Page 262: B.5 Power
Technical specification page b-22 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.5 power supply b.5.1 ac power input this equipment is fitted with an wide-ranging power supply. It is suitable for supply voltages of 100-120 vac -10% +6% or 220-240 vac -10% +6% at 50/60 hz nomin...
Page 263: B.5.2
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-23 st.Re.E10076.3 b.5.2 dc supply input (-48 vdc version) notes... 1. Only model m2/voy/e5750/48v uses a dc power supply. 2. Ensure correct polarity is maintained. 3. The unit must have a protective earth. Table b.38...
Page 264: B.6 Physical
Technical specification page b-24 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.6 physical details table b.39: physical details item specification height 1u, 44.5 mm chassis 2u, 88.9 mm chassis width 1u, 442.5 mm excluding fixing brackets 2u, 442.5 mm excluding fixing bracket...
Page 265: B.8 Compliance
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-25 st.Re.E10076.3 b.8 compliance 1 b.8.1 safety this equipment has been designed and tested to meet the requirements of the following: en 60950 european safety of information technology equipment. Iec 60950 internati...
Page 266: B.8.3 Shock
Technical specification page b-26 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.8.3 shock and vibration the encoder and receiver chassis complies with the requirements of ets 300-019-2-5 table 2, for both non-operational and operational states, without any special mounting or...
Page 267: B.9 Cable
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-27 st.Re.E10076.3 b.9 cable types the signal cable types (or similar) in table b.41 are those recommended by tandberg television in order to maintain product emc compliance. Table b.41: suitable signal cable types si...
Page 268
Technical specification page b-28 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table b.43: dvb asi out 1 connector (disabled) item specification safety status selv connector designation dvb asi out 1 connector type bnc connector impedance 75 Ω 4 data coding 8b/10b channel rate...
Page 269
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-29 st.Re.E10076.3 b.10.3 m2/eom2/dec, sd decoder card option note… the m2/eom2/dec, sd decoder card optionis supported by encoder software version 3.1 and later. Table b.46: asi output (sd decoder) item specification...
Page 270
Technical specification page b-30 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table b.49: audio output (sd decoder) item specification safety status: selv connector type: 15-way d-type female analogue output nominal output impedance: 50 Ω clip level: +6 dbm to +18 dbm samplin...
Page 271: Option
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-31 st.Re.E10076.3 b.10.4 m2/eom2/qpskdemod, qpsk demodulator card option note… the m2/eom2/qpskdemod, qpsk demodulator card optionis supported by encoder software version 3.1 and later. Table b.51: if in (qpsk demodu...
Page 272: Option
Technical specification page b-32 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 b.10.5 m2/eom2/satdemod, 16qam demodulator card option note… the m2/eom2/satdemod, 16qam demodulator card optionis supported by encoder software version 3.1 and later. Table b.54: l-band inputs (16q...
Page 273: Vocality Card Option
Technical specification reference guide: e57xx dsng and deng voyager encoder page b-33 st.Re.E10076.3 b.10.7 m2/eom2/coms/fxs and m2/eom2/coms/fxo vocality card option note… this option is not available for the e5714 encoder. Table b.56: telephone line connector (fxs card) item specification safety ...
Page 274
Technical specification page b-34 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 item specification signal type: rs-422 dce or dte table b.61: lan connector (fxo and fxs cards) item specification safety status: selv connector type: 8-way, rj-45 connector designation: lan signal ...
Page 275
Reference guide: e57xx dsng and deng voyager encoder page c-1 st.Re.E10076.3 annex c c. Language abbreviations languages are shown in alphabetical order. Language abbreviation afrikaans afr albanian alb arabic ara auxiliary two basa bas basque baq bengali ben breton bre bulgarian bul burmese bur cat...
Page 276
Language abbreviations page c-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 language abbreviation somali som spanish spa swahili swa swedish swe tagalog tgl tamil tam telugu tel thai tha tibetan tib turkish tur ukranian ukr undefined und urdu urd vietnamese vie welsh cym xhos...
Page 277: Contents
Reference guide: e57xx dsng and deng voyager encoder page d-1 st.Re.E10076.3 annex d d. Creating and downloading a logo contents d.1 introduction ...............................................................D-3 d.2 summary of features ...............................................D-3 d.3 osd prog...
Page 278
Creating and downloading a logo page d-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 279: D.1 Introduction
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-3 st.Re.E10076.3 d.1 introduction the encoder includes a logo overlay facility whereby an image can be overlaid onto the active video prior to encoding. This enables broadcasters to trademark or brand their m...
Page 280
Creating and downloading a logo page d-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure d.1: web browser interface the dialog box, see figure d.2, will be displayed. Figure d.2: file download dialog box clicking on option open this file from its current location and click...
Page 281: D.4
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-5 st.Re.E10076.3 figure d.3: files for osd creator and loader d.4 creating a logo using osd creator osd creator (creator.Exe) is an application for creating logo files (.Osd format) for use with the osd loade...
Page 282: D.5.2
Creating and downloading a logo page d-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 an example of a logo is shown in figure d.4. Figure d.4: osd creator screen showing example logo d.5.2 loading a .Bmp file select file/open from the menu, and choose a file with a .Bmp extens...
Page 283
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-7 st.Re.E10076.3 osd creator uses a colour palette with a maximum of 256 entries. Each pixel in the image is mapped to an entry in the palette, which holds a value for the red, green and blue and transparency...
Page 284: D.5.4 Downsampling
Creating and downloading a logo page d-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 click the key file toolbar button. Select the key file. The inactive area of the image should now be transparent (background-coloured). Change the background colour to verify that the correct...
Page 285: D.6
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-9 st.Re.E10076.3 d.6 downloading a logo using osd loader the osd loader application (osd.Exe) is used for downloading logo (.Osd) files to the encoder and controlling which are displayed. The application runs...
Page 286: D.7.2
Creating and downloading a logo page d-10 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 the resolution mode must be set to match the video resolution being used. This adjusts the preview screen to the dimensions of the active video. Table d.1: resolution modes resolution mode v...
Page 287
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-11 st.Re.E10076.3 576 lines 1 720 720 pixels digital active picture 702 pixels analogue active picture pixel 1 2 line field 23 336 337 338 24 25 623 310 osd loader co-ordinates (858,619) osd loader co-ordinat...
Page 288: D.7.3
Creating and downloading a logo page d-12 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 d.7.3 show and hide regions the download button defines a region in the encoder, which remains until the encoder is turned off, the remove button is clicked, or the region is downloaded agai...
Page 289: D.8 Fault-Finding
Creating and downloading a logo reference guide: e57xx dsng and deng voyager encoder page d-13 st.Re.E10076.3 d.8 fault-finding if there appears to be a problem creating or downloading a logo check the following: • if the communications box reads "error creating socket", there may be a problem with ...
Page 290
Creating and downloading a logo page d-14 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 291: Contents
Reference guide: e57xx dsng and deng voyager encoder page e-1 st.Re.E10076.3 annex e e. Band plans contents e.1 channels and centre frequencies ...........................E-3 list of tables table e.1: australia .......................................................................E-3 table e.2: eur...
Page 292
Band plans page e-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 293: E.1
Band plans reference guide: e57xx dsng and deng voyager encoder page e-3 st.Re.E10076.3 e.1 channels and centre frequencies the output menu has options called band plan and channel (see chapter 4, operating the equipment locally). Once a country has been selected in the band plan option then the req...
Page 294
Band plans page e-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table e.2: europe vhf uhf channel centre frequency in mhz uhf channel centre frequency in mhz e 2 50.500 e 8 198.500 e 3 57.500 e 9 205.500 e 4 64.500 e 10 212.500 e 5 177.500 e 11 219.500 e 6 184.500 e 12 226.50...
Page 295
Band plans reference guide: e57xx dsng and deng voyager encoder page e-5 st.Re.E10076.3 table e.6: new zealand uhf channel centre frequency in mhz uhf channel centre frequency in mhz 1 47.500 6 191.500 2 57.500 7 198.500 3 64.500 8 205.500 4 177.500 9 212.500 5 184.500 10 219.500 table e.7: china uh...
Page 296
Band plans page e-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table e.9: ireland uhf channel centre frequency in mhz uhf channel centre frequency in mhz i a 48.500 i f 194.000 i b 56.500 i g 202.000 i c 64.500 i h 210.000 i d 178.000 i j 218.000 i e 186.000 table e.10: sout...
Page 297
Band plans reference guide: e57xx dsng and deng voyager encoder page e-7 st.Re.E10076.3 table e.12: france uhf channel centre frequency in mhz uhf channel centre frequency in mhz a 45.000 2 186.750 b 53.000 3 194.750 c 61.000 4 202.750 c1 57.750 5 210.750 1 178.750 6 218.750 table e.13: japan uhf ch...
Page 298
Band plans page e-8 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 table e.14: usa uhf channel centre frequency in mhz uhf channel centre frequency in mhz uhf channel centre frequency in mhz uhf channel centre frequency in mhz a 02 57.000 23 527.000 44 653.000 65 779.000 a 03 63...
Page 299: Contents
Reference guide: e57xx dsng and deng voyager encoder page f-1 st.Re.E10076.3 annex f f. Audio modes contents f.1 analogue audio.........................................................F-3 f.2 digital audio..............................................................F-3 f.3 embedded audio on the sdi...
Page 300
Audio modes page f-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 301: F.1 Analogue
Audio modes reference guide: e57xx dsng and deng voyager encoder page f-3 st.Re.E10076.3 f.1 analogue audio figure f.1 shows the coding methods that may be used with the analogue audio input. Analogue audio code to linear pcm linear pcm internal coding musicam dolby (ac-3) independent of encoder clo...
Page 302: F.3
Audio modes page f-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 figure f.2: digital audio modes f.3 embedded audio on the sdi figure f.3 shows the audio signal flow on the base board. While six audio stereo pairs are available, only two stereo pairs can be processed by the b...
Page 303: F.4
Audio modes reference guide: e57xx dsng and deng voyager encoder page f-5 st.Re.E10076.3 f.4 detail of encoder operation the encoder can de-embed any two did s at any one time, thus giving a total of four embedded audio sources: embedded audio 1-4. The default did for embedded audio 1-2 is 2ffh (gro...
Page 304
Audio modes page f-6 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 305
Reference guide: e57xx dsng and deng voyager encoder page g-1 st.Re.E10076.3 annex g g. Accuracy of frequency sources this equipment is based around iso/iec 13818 specifications (commonly known as mpeg-2) and within these specifications all timing is derived from a 27 mhz system clock. The system cl...
Page 306
Accuracy of frequency sources page g-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 307: Contents
Reference guide: e57xx dsng and deng voyager encoder page h-1 st.Re.E10076.3 annex h h. Use of remux card in atsc contents h.1 remux card in atsc with internal psip.................H-3 h.2 remux card in atsc with external psip................H-3.
Page 308
Use of remux card in atsc page h-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 309: H.1
Use of remux card in atsc reference guide: e57xx dsng and deng voyager encoder page h-3 st.Re.E10076.3 h.1 remux card in atsc with internal psip the encoder automatically remuxes atsc streams arriving at its inputs, as in dvb. The encoder uses the pat (program association table) and pmt (program map...
Page 310
Use of remux card in atsc page h-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 in this configuration the encoder generates the pat, cat and pmt for all programs but it is the responsibility of the user to provide all the psip for the associated programs. Any programs present ...
Page 311: Contents
Reference guide: e57xx dsng and deng voyager encoder page i-1 st.Re.E10076.3 annex i i. Edh capability for e57xx encoders contents i.1 edh capability for e57xx encoders .......................... I-3 list of tables table i.1: edh capability matrix for e57xx encoders.................... I-3.
Page 312
Edh capability for e57xx encoders page i-2 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.
Page 313: I.1
Edh capability for e57xx encoders reference guide: e57xx dsng and deng voyager encoder page i-3 st.Re.E10076.3 i.1 edh capability for e57xx encoders table i.1 contains edh capability for different mux firmware versions. To find the mux firmware version for a particular encoder refer to summary scree...
Page 314
Edh capability for e57xx encoders page i-4 reference guide: e57xx dsng and deng voyager encoder st.Re.E10076.3 blank.