1. DL manuals
  2. TANDBERG
  3. Receiver
  4. TT1280
  5. Reference Manual

TANDBERG TT1280 Reference Manual

Other manuals for TT1280: User Manual

Summary of TT1280

  • Page 1

    St.Re.E10141.5 issue 5 english (uk) reference guide tt1280 and tt1282 high definition professional receiver/decoder software version 2.0.0 (and later) tt1280 and tt1282 hd professional receiver/decoder.

  • Page 2

    Preliminary pages page ii reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 issue 5 first published in 2005 by: t andberg t elevision l td r egistered a ddress : u nit 2 s trategic p ark , c omines w ay , h edge e nd , s outhampton , h ampshire , so30 4da u nited k...

  • Page 3: List of Contents

    Preliminary pages reference guide: tt128x high definition professional receiver/decoder page iii st.Re.E10141.5 list of contents chapter 1: introduction this chapter identifies the equipment versions covered by this manual; describes the purpose of the equipment in a typical system; provides a summa...

  • Page 4: About This Reference Guide

    Preliminary pages page iv reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 about this reference guide this reference guide provides instructions and information for the installation and operation of the tt1280 and tt1282 1u digital integrated receiver/decoder (ird...

  • Page 5: Heed Warnings

    Preliminary pages reference guide: tt128x high definition professional receiver/decoder page v st.Re.E10141.5 warnings, cautions and notes. Heed warnings all warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or d...

  • Page 6: Contact Information

    Preliminary pages page vi reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 contact information tandberg television customer services support services our primary objective is to provide first class customer care that is tailored to your specific business and opera...

  • Page 7: Technical Training

    Preliminary pages reference guide: tt128x high definition professional receiver/decoder page vii st.Re.E10141.5 technical training training courses tandberg television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. Tan...

  • Page 8

    Preliminary pages page viii reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 9: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 1-1 st.Re.E10141.5 chapter 1 1. 1 introduction contents 1.1 scope of this reference guide................................ 1-3 1.1.1 who should use this reference guide....... 1-3 1.1.2 what equipment is covered by this refere...

  • Page 10

    Introduction page 1-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 11: 1.1

    Introduction reference guide: tt128x high definition professional receiver/decoder page 1-3 st.Re.E10141.5 1.1 scope of this reference guide 1.1.1 who should use this reference guide this reference guide is written for operators/users of the tt1280 and tt1282 integrated receiver/decoder (ird). It de...

  • Page 12: 1.2

    Introduction page 1-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 model number marketing code description tt1282 common interface (-48 v version) tt1282/cibas/48v mpeg-2 hd decoder with integrated common interface cam reader, -48 vdc voltage input. Mpeg 4:2:0...

  • Page 13: 1.2.2 Inputs

    Introduction reference guide: tt128x high definition professional receiver/decoder page 1-5 st.Re.E10141.5 • data: dts audio detection and pass-through. Low speed data: rs-232 asynchronous (up to 38.4 kbit/s). High speed data: ethernet data-piping (up to 5 mbit/s) (option). High speed data: rs-422 s...

  • Page 14: 1.2.3 Outputs

    Introduction page 1-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 bpsk/qpsk/8psk/16qam (hom) l-band inputs (satellite receivers) (option) four f-type connectors connect the l-band output of a suitable lnb either directly or via a suitable attenuator giving li...

  • Page 15: 1.3

    Introduction reference guide: tt128x high definition professional receiver/decoder page 1-7 st.Re.E10141.5 there are five relays for failure monitoring (four alarms and one summary alarm). The operator can define (using the alarm menu pages) which alarm conditions drive the relays. This is described...

  • Page 16: 1.3.3

    Introduction page 1-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 1.3.3 what the satellite receiver does the receiver can be tuned to a specified satellite channel frequency and polarisation. The input is down-converted via a low-noise block (lnb) to provide ...

  • Page 17: 1.4

    Introduction reference guide: tt128x high definition professional receiver/decoder page 1-9 st.Re.E10141.5 1.4 the telco receiver/decoder 1.4.1 typical decoder system the decoder is a component of tandberg television’s range of equipment. It is designed for use by broadcasters and distributors of vi...

  • Page 18: 1.4.2

    Introduction page 1-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 1.4.2 what the decoder does the asi interface is used to present the transport stream in the format required by the internal decoder circuitry. At this point, the operation of the unit is the ...

  • Page 19: 1.5.2

    Introduction reference guide: tt128x high definition professional receiver/decoder page 1-11 st.Re.E10141.5 1.5.2 front panel (local) modes operating the ird from the front panel is via two main operating modes: navigate and edit. See section 3.3, front panel operating modes. Figure 1.6: front panel...

  • Page 20: 1.6.3

    Introduction page 1-12 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 figure 1.7: front panel controls 1.6.3 front panel leds figure 1.7 shows the location of the leds on the front panel. The leds indicate the equipment status as follows: the red alarm led is us...

  • Page 21: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 2-1 st.Re.E10141.5 chapter 2 2. Installing the equipment contents 2.1 read this first!......................................................... 2-3 2.1.1 handling ....................................................... 2-3 2....

  • Page 22

    Installing the equipment page 2-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table 2.9: alarm connector......................................................... 2-15 table 2.10: rs-232 low-speed/rs-422 high-speed data connector..................................

  • Page 23: 2.1

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-3 st.Re.E10141.5 2.1 read this first! 2.1.1 handling the ird must be handled and installed carefully and thoughtfully to prevent safety hazards and damage. 2.1.2 installing the equipment ensure the ...

  • Page 24: 2.2

    Installing the equipment page 2-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 2.2 preliminary checks 2.2.1 mechanical inspection warning… removing the covers of this equipment may invalidate any warranties, cause a safety hazard or/and affect the emc performa...

  • Page 25: 2.3

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-5 st.Re.E10141.5 2.3 installing the equipment 2.3.1 fixing the ird is designed for fixed use only and has been shipped with fixing brackets suitable for a standard 19-inch rack. When installed in a ...

  • Page 26: 2.3.3

    Installing the equipment page 2-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 protection from moisture do not install this equipment in areas of high humidity or where there is a danger of water ingress. 2.3.3 installing cables - safety power supply cables sh...

  • Page 27: 2.5.2

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-7 st.Re.E10141.5 warnings… 1. The tt1280 and tt1282 should only be operated from the type of power source indicated on the marking label. If you are not sure of the type to your business, consult yo...

  • Page 28: 2.5.3

    Installing the equipment page 2-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table 2.2: non standard supply cord wire colours wire colour (uk) action green-and-yellow ...Must be connected to the terminal in the plug which is marked with the letter e or the s...

  • Page 29: 2.6.3

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-9 st.Re.E10141.5 2.6.3 connecting the equipment to the dc power supply connect the receiver to the local d.C. Power supply as follows. 1. Local dc power supply ensure the power supply is isolated an...

  • Page 30: 2.8 Signal

    Installing the equipment page 2-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 2.8 signal connections 2.8.1 general caution... It is strongly recommended that the terminal marked at the rear panel of the equipment is connected to a site technical earth before...

  • Page 31

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-11 st.Re.E10141.5 figure 2.5: signal connections asi/ssi frame sync asi/ssi in frame synchronisation asi transport streams asi transport streams analogue/digital audio output analogue/digital audio ...

  • Page 32: 2.8.2 Asi

    Installing the equipment page 2-12 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 2.8.2 asi out two bnc sockets output asi transport streams with a maximum data rate of 160 mbit/s. Note… these sockets are shared with the hd sdi output, under the control of menu ...

  • Page 33: 2.8.4

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-13 st.Re.E10141.5 2.8.4 svga output (rgb hv) the ird is equipped with a svga 15-pin d-type connector for video output in the standard configuration. The svga connector shall be set to rgb/hv (svga) ...

  • Page 34: 2.8.6 Frame

    Installing the equipment page 2-14 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 note… these connectors are shared with the asi output, under the control of menu 5.1. 2.8.6 frame synchronisation a bnc socket is used by the decoder to frame lock to an external v...

  • Page 35: 2.8.8

    Installing the equipment reference guide: tt128x high definition professional receiver/decoder page 2-15 st.Re.E10141.5 2.8.8 alarm connector and relay the alarm relay connector has a summary and four general purpose relays. The summary relay is activated whenever the unit detects an alarm, or the p...

  • Page 36: 2.9

    Installing the equipment page 2-16 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 2.9 option card connectors option cards are described in chapter 6, options..

  • Page 37: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 3-1 st.Re.E10141.5 chapter 3 3. Operating the equipment locally contents 3.1 powering the equipment........................................... 3-3 3.1.1 switching on ................................................ 3-3 3.1.2 ...

  • Page 38

    Operating the equipment locally page 3-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 list of tables table 3.1: navigate mode ............................................................. 3-4 table 3.2: edit mode ..................................................

  • Page 39: 3.1

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-3 st.Re.E10141.5 3.1 powering the equipment 3.1.1 switching on caution... This equipment should not be operated unless the cooling fan is working and there is free-air flow around the unit. C...

  • Page 40: 3.2

    Operating the equipment locally page 3-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.2 front panel controls and pushbuttons front panel items are described under section 1.6, guided tour. Figure 3.2: front panel controls and pushbuttons 3.3 front panel oper...

  • Page 41

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-5 st.Re.E10141.5 the front panel returns to navigate mode when edit is pressed again (abort edit with no save) or when save is pressed (save modified parameter values). Processing of events f...

  • Page 42: 3.4

    Operating the equipment locally page 3-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.4 using the local controls 3.4.1 lcd menu descriptions detailed lcd menu descriptions are given in annex c, menus. This chapter concentrates on describing the use of the me...

  • Page 43: 3.5

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-7 st.Re.E10141.5 3.5 setting up preset services (menu 1) 3.5.1 using preset services this group allows up to 40 services to be stored as presets. Selecting a service from the preset list in m...

  • Page 44: 3.6.2

    Operating the equipment locally page 3-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 step action result 7 scroll to menu 2.3.2.5. Enter the lnb 22 khz setting then press save. Enables or disables the lnb 22 khz control tone for the selected source (on, off). ...

  • Page 45: 3.6.3

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-9 st.Re.E10141.5 3.6.3 dvb-s2 satellite receiver (tt1280/hwo/dvbs2 and tt1280/hwo/dvbs2/if/const) table 3.8: setting up the dvb-s2 satellite receiver step action result 1 go to menu 2.3 and s...

  • Page 46: 3.6.4

    Operating the equipment locally page 3-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.6.4 telco receiver - ttv g.703 table 3.9 steps through the set up procedure of the telco receiver using menu 2 input, and the ttv g.703 input. Table 3.9: setting up the tt...

  • Page 47: 3.7

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-11 st.Re.E10141.5 step action result 7 navigate to ip input multicast ip add (menu 2.3.2.4), then press edit. Select the multicast ip address, then press save. Edits the ip input multicast ip...

  • Page 48: 3.7.3

    Operating the equipment locally page 3-12 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.7.3 selecting the audio component introduction automatic audio component selection is based on component order in the pmt as follows: • audio 1 selects the first component...

  • Page 49: 3.7.4

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-13 st.Re.E10141.5 3.7.4 setting up asynchronous data (rs-232) these menu pages allow status monitoring and configuration of the low speed data. Table 3.14: setting up async data step action r...

  • Page 50: 3.7.7

    Operating the equipment locally page 3-14 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.7.7 setting up closed captions table 3.17: setting up closed captions step action result 1 scroll to menu 3.8.2 and edit the parameter for enabling closed captions pass th...

  • Page 51: 3.8.2

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-15 st.Re.E10141.5 biss (as specified in ebu tech 3292 may 2002) is standard on all units. It is not possible to have both dvb common interface and tandberg director options fitted on the same...

  • Page 52: 3.9

    Operating the equipment locally page 3-16 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.9 setting up the transport stream output (menu 5) 3.9.1 set-up procedure use table 3.21 to step through the transport stream output set-up procedure using menu 5. This all...

  • Page 53: 3.9.4

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-17 st.Re.E10141.5 3.9.4 transport stream packet lengths the input transport stream packet lengths may be 188/204/208 bytes. With the transport stream output set to post input or post ts descr...

  • Page 54

    Operating the equipment locally page 3-18 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 3.11 setting up system parameters (menu 7) this menu gives access to the setup menu to set up and edit system parameters as well as the ird details menu (see table 3.26). Ta...

  • Page 55: 3.12  Restarting The Unit

    Operating the equipment locally reference guide: tt128x high definition professional receiver/decoder page 3-19 st.Re.E10141.5 3.12 restarting the unit the system restart submenu allows the user to reboot the unit without having to remove and insert the power cable. Table 3.27: system restart menu s...

  • Page 56

    Operating the equipment locally page 3-20 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 57: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 4-1 st.Re.E10141.5 chapter 4 4. Operating the equipment remotely contents 4.1 remote control......................................................... 4-3 4.1.1 introduction................................................... 4...

  • Page 58

    Operating the equipment remotely page 4-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 59: 4.1 Remote

    Operating the equipment remotely reference guide: tt128x high definition professional receiver/decoder page 4-3 st.Re.E10141.5 4.1 remote control 4.1.1 introduction the ird can be remotely controlled in a variety of ways. The basic control methods are: • tandberg device controller (tdc) • third-part...

  • Page 60: 4.1.5

    Operating the equipment remotely page 4-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table 4.2: configuring the serial remote port and activating remote protocol step action result 1. Go to menu 7.1. Displays ‘operating mode’. 2. Press edit. Displays ‘front ...

  • Page 61: 4.2

    Operating the equipment remotely reference guide: tt128x high definition professional receiver/decoder page 4-5 st.Re.E10141.5 entering the oac lockout pin table 4.4: entering the oac lockout pin step action result 1. Go to menu #4.3.6 director. Displays ‘ncp lock override pin’. 2. Press edit. Displ...

  • Page 62

    Operating the equipment remotely page 4-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 63: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 5-1 st.Re.E10141.5 chapter 5 5. Alarms contents 5.1 introduction ............................................................... 5-3 5.2 location of the alarm and lock leds....................... 5-3 5.3 alarm led...............

  • Page 64

    Alarms page 5-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 65: 5.1 Introduction

    Alarms reference guide: tt128x high definition professional receiver/decoder page 5-3 st.Re.E10141.5 5.1 introduction there are two front panel leds that indicate the status of the ird. These are used to indicate abnormal performance of the unit. 5.2 location of the alarm and lock leds the red alarm...

  • Page 66

    Alarms page 5-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 it is possible to signal additional alarms depending on the transport stream input type and optional functionality in the unit. Satellite inputs: • bit error rate (ber) above (programmable) threshold...

  • Page 67: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 6-1 st.Re.E10141.5 chapter 6 6. Options contents 6.1 hardware enabled options....................................... 6-3 6.2 qpsk input card (tt1280/hwo/qpsk).................. 6-3 6.2.1 general..................................

  • Page 68

    Options page 6-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 69: 6.1 Hardware

    Options reference guide: tt128x high definition professional receiver/decoder page 6-3 st.Re.E10141.5 6.1 hardware enabled options these options require extra hardware to be fitted to the unit. Contact the customer services helpdesk for details (see preliminary pages). 6.2 qpsk input card (tt1280/hw...

  • Page 70: 6.3

    Options page 6-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 caution… 1. The receiver provides dc power (refer to chapter 3, operating the equipment locally) via the active l-band input connector to drive an lnb (low noise block down-converter). Do not connec...

  • Page 71: 6.4

    Options reference guide: tt128x high definition professional receiver/decoder page 6-5 st.Re.E10141.5 6.4 dvb-s2 input cards (tt1280/hwo/dvbs2 and tt1280/hwo/dvbs2/if/const) 6.4.1 general the dvb-s2 input card supports dvb-s, qpsk demodulation and dvb-s2, qpsk and 8psk demodulation. Two options are ...

  • Page 72: 6.4.4

    Options page 6-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 the specification for this connector is given in annex b, technical specification. Table 6.4: dvb-s2 satellite receiver (if monitor input) connector input specification connector type bnc, female co...

  • Page 73: 6.6

    Options reference guide: tt128x high definition professional receiver/decoder page 6-7 st.Re.E10141.5 6.6 ip input card (tt1280/hwo/ip) the ip input card provides a 10/100baset ethernet port, on which a transport stream can be received in udp packets at up to 50 mbit/s. The mapping of mpeg-2 ts pack...

  • Page 74: 6.7 Software

    Options page 6-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 6.7 software enabled options these options may be enabled through software licence keys. Contact the customer services helpdesk for details (see preliminary pages). 6.8 high speed data over ethernet...

  • Page 75: Contents

    Reference guide: tt128x high definition professional receiver/decoder page 7-1 st.Re.E10141.5 chapter 7 7. Preventive maintenance and fault- finding contents 7.1 routine checks......................................................... 7-3 7.1.1 cooling fan ...............................................

  • Page 76

    Preventive maintenance and fault-finding page 7-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 blank.

  • Page 77: 7.1 Routine

    Preventive maintenance and fault-finding reference guide: tt128x high definition professional receiver/decoder page 7-3 st.Re.E10141.5 7.1 routine checks 7.1.1 cooling fan there are no routine checks associated with this equipment other than to ensure that the unit is adequately cooled. This equipme...

  • Page 78: 7.2.2 Replacement

    Preventive maintenance and fault-finding page 7-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 4. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an...

  • Page 79: 7.4 Fault-Finding

    Preventive maintenance and fault-finding reference guide: tt128x high definition professional receiver/decoder page 7-5 st.Re.E10141.5 for systems support you can choose either gold or silver advantage. These packages are designed to save you costs and protect your income through enlisting the help ...

  • Page 80: 7.5

    Preventive maintenance and fault-finding page 7-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 7.5 changing the equipment fuse 7.5.1 ac user accessible fuse replacement caution... This product should be operated only from the type of power source indicated on ...

  • Page 81: 7.5.2

    Preventive maintenance and fault-finding reference guide: tt128x high definition professional receiver/decoder page 7-7 st.Re.E10141.5 figure 7.2: fuse carrier if the replacement fuse also blows, do not continue. Disconnect the equipment and contact tandberg customer services (see preliminary pages)...

  • Page 82: 7.6 Disposal

    Preventive maintenance and fault-finding page 7-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 7.6 disposal 7.6.1 moulded plugs if the moulded plug fitted to the mains cable supplied with this equipment is not required, use another cable. If the supplied plug ...

  • Page 83

    Reference guide: tt128x high definition professional receiver/decoder page a-1 st.Re.E10141.5 annex a a. Glossary the following list covers most of the abbreviations, acronyms and terms as used in tandberg television limited manuals, user and reference guides. All terms may not be included in this r...

  • Page 84

    Glossary page a-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b3zs bipolar with three zero substitution: a method of eliminating long zero strings in a transmission. It is used to ensure a sufficient number of transitions to maintain system synchronisation wh...

  • Page 85

    Glossary reference guide: tt128x high definition professional receiver/decoder page a-3 st.Re.E10141.5 cofdm coded ofdm: cofdm adds forward error correction to the ofdm transmission consisting of reed-solomon (rs) coding followed by convolutional coding to add extra bits to the transmitted signal. T...

  • Page 86

    Glossary page a-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 dvb si digital video broadcasting service information. Dvb-pi dvb-professional interfaces: ttv lan search shows – dvb physical interfaces earth technical earth: ensures that all equipment chassis w...

  • Page 87

    Glossary reference guide: tt128x high definition professional receiver/decoder page a-5 st.Re.E10141.5 hub a device in a multipoint network at which branch nodes interconnect. Icam integrated conditional access module: embedded in the ird and responsible for descrambling, plus packet filtering and r...

  • Page 88

    Glossary page a-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 lnb low noise block down-converter: the component of a subscriber satellite transmission receiving dish which amplifies the incoming signal and down-converts it to a suitable frequency to input to ...

  • Page 89

    Glossary reference guide: tt128x high definition professional receiver/decoder page a-7 st.Re.E10141.5 nit network information table: part of the service information data. The nit provides information about the physical organisation of each transport stream multiplex, and the characteristics of the ...

  • Page 90

    Glossary page a-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 p-picture/p-frame a picture / frame produced using forward prediction. It contains predictions from either previous i frames or previous p frames. The p frame is used as a reference for future p or...

  • Page 91

    Glossary reference guide: tt128x high definition professional receiver/decoder page a-9 st.Re.E10141.5 stb set-top box: a box that sits on top of a television set and is the interface between the home television and the cable tv company. New technologies evolving for set-top boxes are video-on-deman...

  • Page 92

    Glossary page a-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 transport stream a set of packetised elementary data streams and si streams, which may comprise more than one programme, but with common synchronisation and error protection. The data structure is...

  • Page 93: Contents

    Reference guide: tt128x high definition professional receiver/decoder page b-1 st.Re.E10141.5 annex b b. Technical specification contents b.1 output ......................................................................B-3 b.1.1 supported video resolutions .......................B-3 b.1.2 supported ...

  • Page 94

    Technical specification page b-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table b.3: analogue audio performance specifications............... B-6 table b.4: supported audio specifications ................................... B-6 table b.5: supported audio d...

  • Page 95: B.1 Output

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-3 st.Re.E10141.5 b.1 output b.1.1 supported video resolutions the ird supports 4:2:0 mp@hl and 4:2:2 p@ml (tt1282 only) with video resolutions described in table b.1. Table b.1: supported video resol...

  • Page 96: B.1.4 Hd

    Technical specification page b-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b.1.4 hd sdi hd sdi output supports: • embedded decoded audios • closed captioning (eia 708b) • vitc b.2 audio decoding and output stage b.2.1 general the ird is capable of simultane...

  • Page 97: B.2.4 Linear

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-5 st.Re.E10141.5 it is possible to output the compressed dolby digital stream from the digital audio output, allowing it to be decoded to 5.1 channels by an external decoder. Sampling rates (khz): 32...

  • Page 98: B.3.3 Audio

    Technical specification page b-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table b.3: analogue audio performance specifications parameter conditions limit gain 0 dbm input level ±1 db frequency response 100 hz - 15 khz, 0 dbm input level ±0.2 db 20 hz - 20 ...

  • Page 99: B.3.6

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-7 st.Re.E10141.5 b.3.6 supported audio bit-rates table b.5: supported audio data bit-rates (mpeg-2) mono kbit/s stereo kbit/s mono kbit/s stereo kbit/s 32 64 96 192 48 96 112 224 56 112 128 256 64 12...

  • Page 100

    Technical specification page b-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 parameter specification modulation signal type qpsk per en 300 421 3 convolutional fec rates 1/2, 2/3, 3/4, 5/6, 7/8 symbol rate range rs = 1.0 to 45.0 msymbol/s symbol rate step 1 s...

  • Page 101

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-9 st.Re.E10141.5 table b.8: qpsk bit-rate r188 limits (mbit/s) fec r188min r188max 1/2 1.000000 41.470588 2/3 1.228758 55.294118 3/4 1.382353 62.205882 5/6 1.535948 69.117647 7/8 1.612745 72.573529 l...

  • Page 102: B.4.2

    Technical specification page b-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b.4.2 hom satellite receivers general table b.10: hom satellite receiver input specification parameter specification l-band input safety status selv number of inputs 4 input connect...

  • Page 103

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-11 st.Re.E10141.5 table b.11: l-band satellite input — eb/no ratio convolutional fec rate eb/no ratio (db) in if loop for correct mpeg-2 system operation 1/2 qpsk 4.5 2/3 qpsk 5.0 3/4 qpsk 5.5 5/6 qp...

  • Page 104: B.4.3 Dvb-S2

    Technical specification page b-12 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b.4.3 dvb-s2 satellite receivers general table b.13: dvb-s2 satellite receiver input specification parameter specification l-band input safety status selv number of inputs 4 (tt1280...

  • Page 105

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-13 st.Re.E10141.5 parameter specification qpsk ldpc fec rates 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9. 9/10 8psk, ldpc fec rates 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 ldpc fec frame length normal pilot tones autom...

  • Page 106

    Technical specification page b-14 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 eb/no ratio is referred to user bit-rate ru188. See en 300 421 specification. For more detailed specification information and advice on performance in specific applications, please ...

  • Page 107: B.4.4

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-15 st.Re.E10141.5 table b.16: lnb power and control parameter specification voltage v (nominal) receiver polarisation 14 voltage 13 18 vertical/circular right horizontal/circular left current 350 ma ...

  • Page 108: B.4.7

    Technical specification page b-16 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 input specification safety status selv connector type 8 way rj-45 connector designation 10/100 bt signal type 10/100baset ethernet (ieee 802.3/802.3u) data rate 1.5 – 50 mbit/s b.4....

  • Page 109

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-17 st.Re.E10141.5 connector type 15-way d-type connector designation video out video standards 1080 interlaced video level (luminance) 700 mv ± 30 mv.

  • Page 110: B.5.2 Audio

    Technical specification page b-18 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 digital video table b.23: digital video output connectors item specification safety status selv connector type bnc, female, 75 Ω connector designation hd sdi 1 hd sdi 2 output stand...

  • Page 111: B.5.4

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-19 st.Re.E10141.5 table b.26: rs-422 synchronous (high-speed) data connector item specification safety status selv connector type 9-way d-type connector designation rs232/rs422 data out data-rates (b...

  • Page 112: B.6 Environmental

    Technical specification page b-20 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 item specification maximum switching voltage 50 vdc / 30 vac maximum switching power 24 w / 60 va minimum switching load 0.1 ma, 100 mvdc b.6 environmental b.6.1 conditions table b....

  • Page 113: B.7 Power

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-21 st.Re.E10141.5 b.7 power supply b.7.1 ac mains input this equipment is fitted with a wide-ranging power supply. It is suitable for supply voltages of 100-120 vac -10% +6% or 220-240 vac -10% +6% a...

  • Page 114: B.7.2

    Technical specification page b-22 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b.7.2 dc supply input (-48 v version) notes... 1. Only models tt1280/cibas/48v, tt1280/dirbas/48v, tt1282/cibas/48v and tt1282/dirbas/48v use a dc power supply. 2. Ensure correct po...

  • Page 115: B.9 Compliance

    Technical specification reference guide: tt128x high definition professional receiver/decoder page b-23 st.Re.E10141.5 b.9 compliance 15 b.9.1 safety this equipment has been designed and tested to meet the requirements of the following: en 60950 european safety of information technology equipment. I...

  • Page 116: B.9.3 Ce

    Technical specification page b-24 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 b.9.3 ce marking the ce mark is affixed to indicate compliance with the following directives: 89/336/eec of 3 may 1989 on the approximation of the laws of the member states relating...

  • Page 117: Contents

    Reference guide: tt128x high definition professional receiver/decoder page c-1 st.Re.E10141.5 annex c c. Menus contents c.1 lcd menus ...............................................................C-3 c.1.1 using the menus...........................................C-3 c.1.2 menu descriptions...........

  • Page 118

    Menus page c-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 table c.21: output connector selector submenu......................C-14 table c.22: alarms menu............................................................C-15 table c.23: transport stream alarm setup...

  • Page 119: C.1 Lcd

    Menus reference guide: tt128x high definition professional receiver/decoder page c-3 st.Re.E10141.5 c.1 lcd menus c.1.1 using the menus detailed description of the use of menus is given in chapter 3, operating the equipment locally. C.1.2 menu descriptions this annex describes the front panel lcd me...

  • Page 120: C.3

    Menus page c-4 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.3 the menu structure section c.9 section c.6 section c.8 section c.4 section c.5 6. Alarms 4. Conditional menu 5. Ts output 5.1 connector 1/2 7. System 2. Input (qpsk, hom, g.703 or ip) 1. Presets t...

  • Page 121: C.4

    Menus reference guide: tt128x high definition professional receiver/decoder page c-5 st.Re.E10141.5 c.4 presets menu items (menu 1) the presets menu contains up to 40 editable preset numbers in the range 01 – 40. Selecting a service via the presets menu automatically reconfigures the input of the ir...

  • Page 122: C.5.3 Ssi

    Menus page c-6 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.5.3 ssi menu when the ssi (smpte 310) source is selected this menu allows the user to monitor the signal lock status. Table c.5: input selection menu display title: smpte 310 description wwwwwwwwww ...

  • Page 123: C.5.5 Hom

    Menus reference guide: tt128x high definition professional receiver/decoder page c-7 st.Re.E10141.5 c.5.5 hom satellite option menu when a higher order modulation input interface is used, the input menu allows the user to edit the hom parameters. Table c.7: hom satellite menu display title: input de...

  • Page 124: C.5.6

    Menus page c-8 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.5.6 ttv g.703 (ds3 and e3) option menu when a ttv g.703input interface is used, the input menu allows the user to edit the set-up parameters table c.8: ttv g.703 menu display title: input descriptio...

  • Page 125: C.6

    Menus reference guide: tt128x high definition professional receiver/decoder page c-9 st.Re.E10141.5 c.6 service menu (menu 3) c.6.1 overview the service menu allows access to the currently available services. This group provides a summary of the data streams associated with the decoded service. In t...

  • Page 126

    Menus page c-10 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 display title: video description gop structure y…..Y pixel aspect ratio yyy y…..Y video gop structure and length yyy is the current video aspect ratio (16:9) rate buffer level xxx% bit-rate yy.Yy mbi...

  • Page 127: C.6.3

    Menus reference guide: tt128x high definition professional receiver/decoder page c-11 st.Re.E10141.5 c.6.3 audio 1 menu the audio 1 signal status submenu contains information about the audio format and status of the currently decoded audio stream on the primary audio output. Table c.12: audio 1 menu...

  • Page 128: C.6.5 Async

    Menus page c-12 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.6.5 async data menu the async data submenu allows status monitoring and configuration of the low speed data. Table c.14: async data menu display title: async data description ww streams pid xxxx yy...

  • Page 129: C.6.8 Vbi

    Menus reference guide: tt128x high definition professional receiver/decoder page c-13 st.Re.E10141.5 c.6.8 vbi menu the vbi status submenu displays the current status of the vbi components. Note… the vitc menu functionality is not supported in software version 1.0.0. Table c.17: vbi menu display tit...

  • Page 130: C.7

    Menus page c-14 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.7 transport stream output menu c.7.1 overview the transport stream output submenu allows editing of the position of the asi output. Table c.20: transport stream output menu display title: transport...

  • Page 131: C.8

    Menus reference guide: tt128x high definition professional receiver/decoder page c-15 st.Re.E10141.5 c.8 alarms menu (menu 6) c.8.1 overview the alarms menu provides a summary of the alarm status. Table c.22: alarms menu display title: alarms description section transport stream alarm setup transpor...

  • Page 132: C.8.3

    Menus page c-16 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.8.3 video alarm setup menu table c.24: video alarm setup menu display title: description if video not running yyyyyyyyyyyyyy yyyyyyyyyyyyyy is editable: no alarm set alarm only set alarm and relay ...

  • Page 133: C.8.5

    Menus reference guide: tt128x high definition professional receiver/decoder page c-17 st.Re.E10141.5 c.8.5 audio 2 alarm setup menu table c.26: audio 2 alarm setup menu display title: description if audio 02 not running yyyyyyyyyyyyyy yyyyyyyyyyyyyy is editable: no alarm set alarm only set alarm and...

  • Page 134: C.8.7

    Menus page c-18 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.8.7 mer alarm setup menu table c.28: mer alarm setup menu display title: description if mer less than xx.X yyyyyyyyyyyyyy yyyyyyyyyyyyyy is editable 0 to 69.9: no alarm set alarm only set alarm and...

  • Page 135: C.9

    Menus reference guide: tt128x high definition professional receiver/decoder page c-19 st.Re.E10141.5 c.9 system menu (menu 7) c.9.1 setup menu the setup submenu allows the user to edit the operating mode, lcd contrast, serial remote protocol, ip address, subnet mask, service hunt mode, and the custo...

  • Page 136: C.9.2

    Menus page c-20 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 c.9.2 ird details menu the ird details submenu displays the software, firmware, hardware, pld version and electronic serial number of the ird. Table c.31: ird details menu display title: ird details ...

  • Page 137

    Reference guide: tt128x high definition professional receiver/decoder page d-1 st.Re.E10141.5 annex d d. Language abbreviations languages are shown in alphabetical order. No language abbreviation 5 arabic ara basa bas 14 bengali ben 135 chinese chi 19 czech cze 21 danish dan 82 dutch dut 25 english ...

  • Page 138

    Language abbreviations page d-2 reference guide: tt128x high definition professional receiver/decoder st.Re.E10141.5 the following non-iso 1 languages are supported. Note… only applicable for a transport stream going to an alteia receiver. Language abbreviation main one aux two international sound i...

  • Page 139

    Reference guide: tt1280 high definition professional receiver/decoder page e-1 st.Re.E10141.5 annex e e. Factory defaults units are shipped with the following factory default parameters. These can be restored at any time using the system menu. All other parameters are unaffected by restoring the fac...

  • Page 140

    Factory defaults page e-2 reference guide: tt1280 high definition professional receiver/decoder st.Re.E10141.5 menu description default clipping level 18 db ac3 downmix method surround stereo async data enabled sync data (high speed ethernet data not fitted) enabled eth.Net data (high speed ethernet...