Tansun SH2-1200W UK Reference Manual - page 4
I n t r o d u c t i o n
The Tansun range of Eclipse heaters contain long-life ceramic elements which are
highly efficient and durable. The heaters are mounted on adjustable brackets that
allows the heat to be directed exactly where it is required. Its attractive design means
that it is effective yet unobtrusive. The Eclipse heaters are designed for indoor and
outdoor use and is therefore weatherproof.
Please read the caution notes and following instructions carefully before use.
The safety of this heater is guaranteed only by its correct usage in accordance
with these instructions, therefore it is recommended that they are retained for
future reference.
S p e c i f i c a t i o n
Ta b l e 1 . U K a n d E u r o p e a n H e a t e r s
Use an MCB Type 3 or C.
Model
SH2-1200W
SH3-1800W
SH4-2400W
Description
Double
Triple
Quadruple
Voltage (V)
230
230
230
No. of Elements x
Power (W)
2 x 600
3 x 600
4 x 600
Total Power (kW)
1.2
1.8
2.4
Total Current (A)
5.2
7.8
10.4
Min. height from
floor (m)
2.0
2.0
2.0
Min. distance from
ceiling (m)
0.3
0.3
0.3
Min. distance from
side wall (m)
0.5
0.5
0.5
Dimensions (depth
inc. bracket in max.
pos.) L x H x D (mm)
940 x 111 x 169
1300 x 111 x 169
1660 x 111 x 169
Weight (kg)
5.2
7.1
8.9
Ingress
Protection (IP)
IPx4
IPx4
IPx4
4
I n s t a l l a t i o n
•
Warning - this appliance must be connected to an earthed supply.
•
All version are fitted with 3.0 metres of mains supply cord and a moulded plug,
therefore it is unnecessary to remove the terminal box in order to carry out
normal installation of these models.
W a l l M o u n t i n g
•
The Eclipse heater should be
mounted in a horizontal manner only
(see Fig. A ).
•
Do not position the heater at an
angle more than 70° and less than
45° from the mounting surface as
shown in Fig. A.
•
Always allow the heater to cool
before attempting to reposition/move.
Never attempt to move the heater
while it is switched on!
•
Observe the minimum safe distance
between the heater body and
inflammable surfaces and objects
when mounting.
•
Please refer to Table 1 for the
recommended positioning of the
heater. Do not install the heater in a
corner!
•
Do not mount the heater on plastic
soffits and fascia boards and ensure
the mounting surface will suitably
withstand the radiant heat from the
heater body.
5
I n s t a l l a t i o n c o n t i n u e d . . .
•
All installations must be in accordance with the latest I.E.E. safety regulations or
equivalent.
•
We recommend using a RCD where applicable.
•
If the supply cord becomes damaged, it must be replaced by the manufacturer,
its service agent or a similar qualified person in order to avoid a hazard.
•
Please observe the minimum safe distance between the heater body and any
inflammable surfaces.
•
If in any doubt, please contact a suitably qualified electrician.
•
To disconnect heater, remove the mains plug from the socket outlet.
Max. 70°
Min. 45°
2.
0m
M
IN
.
H
EI
G
H
T
F
RO
M
F
L
O
O
R
GROUND LEVEL
Fig. A
Continued on next page...