Target TA10100 Operating Instructions And Parts List Manual - page 14
14
Water Pump (E), Hose Barb (F), Water Valve (G),
15/16" Wrench (N), Drain Plug (P), Locking Knob
(C) with 5/16" flatwasher, Bearing Caps with 5/16
Capscrews & Flatwashers and Set Collar (B).
6.
Literature Assembly Envelope
NOTE: Check the carton and all packing filler for loose parts
and optional accessories (if ordered).
IF ANY PARTS ARE MISSING OR DAMAGED, PLEASE
CONTACT YOUR TARGET CUSTOMER SERVICE FOR
INSTRUCTIONS. CALL 1-800-288-5040
Set the Frame Assembly (2) on a flat surface or on a
TARGET® folding stand.
Install the Water Pan Assembly (3) between the four
Guides (Q) on the Frame Assembly (2). Locate the Pan
with the Drain Plug (P) at the operating end with the two
Stops located on the bottom of the Pan (3) straddling
the front leg of the Frame.
The Water Pan Assembly
(3) should slide freely back and forth on the Guides (Q)
with little lateral movement. Adjust if needed.
Install the Cutting Head Assembly (1):
1.
Set the Cutting Head Assembly (1) on the pivot
bar up between the two Set Collars (A). The set
collars have been pre-set at the factory to align the
blade with the slot in the center of the cart; it can
be adjusted if needed.
2.
Using the 5/16 Capscrews and Lockwashers pro-
vided, install the two Bearing Caps (B) to the bot-
tom of the Cutting Head. Next, tighten the
Capscrews with the wrench provided to securely
hold the Cutting Head (1) onto the pivot bar, but
loose enough so it can be moved up or down.
3.
Insert the Locking Knob (C) with 5/16" flatwasher
through the slotted Lockbar (D) into the tapped
hole in the belt guard. This is used to set the
cutting depth of the blade. See section 5.
Water Pump Assembly (5) Set-up:
1.
Remove the Water Pump (E), Hose Barb (F), the
Water Control Valve (G) and Water Tube Assem-
bly (H) from their carton. Thread the Hose Barb
(F) on the water pump outlet, hand tighten.
2.
Slide the Control Valve (G) onto the flexible plastic
tubing and push the open end onto the Hose
Barb (F).
3.
Set the Water Pump Assembly (5) in the deep end
of the pan beneath the belt guard. Note: The
water pump inlet screen must be submerged
in order to properly pick up water.
4.
Place the Water Tube Assembly (H) to the back of
the Blade Guard (J) and insert the two 1/4" plastic
nozzles into the two Ports (I) on the side of the
Blade Guard (J). To prevent interference with the
full movement of the cart, it is recommended that
the tubing and electrical cord exit out the back
through the indented area of the pan.
5.
Insert the male plug into the Receptacle (O) on the
motor. The Water Pump (E) will start when the
motor is turned on. For dry cutting, the water pump
should be unplugged or removed to prevent dam-
age to the pump.
NOTE: THE MOTOR WATER PUMP OUTLET IS
NOT TO BE USED AS A GENERAL PURPOSE
CONVENIENCE OUTLET. USE FOR CONNECTON
OF THE SUPPLIED WATER PUMP ONLY.
WATER PUMP SAFETY GUIDELINES
Always plug the saw power cord into a GFCI
outlet when using. If a GFCI type outlet is not
available, use a plug-in type GFCI plugged into a
properly grounded outlet. Do not use any
temporary plug adapters.
·
The water pump is equipped with a ground electrical
plug, to reduce the risk of possible shock. Be sure to
connect to a properly grounded type receptacle.
·
Never pick the water pump up out of the water when it
is plugged in.
·
DO NOT EVER use the water pump to pump anything
but water.
·
Never service the pump when it is still plugged in.
·
Never let the pump operate dry. It is self-cooled by
pumping water. Dry use will cause the pump to fail.
·
Maintain regularly and clean out debris from intake
screen.
·
Check the power cord for nicks or frays and never try
to alter the power cord in any way.
Install the Cutting Blade:
Always set the Motor Switch to OFF prior to
mounting the blade.
1.
Be sure you are using the correct blade for the
material being cut. For example, blades are
available for cutting materials such as wall tile,
quarry tile, marble, slate and similarly hard materi-
als. For the best results, always use genuine TAR-
GET® diamond blades. Contact your nearest
dealer to select the correct blade for your specific
cutting needs.
2.
Rotate the Blade Guard (J) fully up, tightening the
wing nut if needed to hold it in the fully raised
position.
3.
Remove the Blade Shaft Nut (L) and the Outer
Blade Flange (M2).
4.
Check the blade for Counter Clockwise rotation
(CCW) and install on the spindle shaft.
Rotation direction is indicated by an arrow on one
side of the blade. Make sure the blade contact
surfaces are clean.
5.
Install the Outer Flange (M2) with the large diam-
eter against the Blade (K). Tighten the Blade Shaft
Nut (L) with the 15/16" Wrench (N) provided.