- DL manuals
- Tascam
- Music Mixer
- TM-D1000
- Operation Manual
Tascam TM-D1000 Operation Manual - 13 - Options
13 - Options
35
TASCAM TM-D1000 Operations Manual
channels 1 + 2 and 5 + 6, they will also be routed to
the TDIF-1 B channels with the same numbers.
If input channels are routed using the DIRECT OUT
function, and the IF-TD1000 Digital I/O board is fit-
ted, the input channels will be output to the TDIF-1
B
connector. It may also be selected to be output in
parallel to both TDIF-1 connectors (
A
and
B
) by
selecting input channels 1–8 as the source for TDIF-
1
A
.
13.3FX-D1000 Effect Board
The FX-D1000 Effect Board provides an additional
set of effect processors, doubling the capacity of the
TM-D1000’s internal processor capability.
Effect patterns are still subject to the same restric-
tions as regards groups and aux busses (i.e. if there
are no aux busses, no aux sends are possible).
However, the FX-D1000 Effect Board provides you
with much more power and flexibility in the way that
you use the internal effect system of the TM-D1000.
WARNING
This board requires internal connections to
the TM-D1000. For this reason, you should
not install the board yourself, but should refer
installation to a qualified TASCAM distributor.
Summary of TM-D1000
Page 1
1 tascam tm-d1000 operations manual 1 - tm-d1000 operations manual congratulations on your purchase of the tm-d1000. This high-quality digital mixing console allows you to produce crystal-clear multitrack recordings and to mix them to a digital stereo mastering machine. We do not expect you to read ...
Page 2
1 - tm-d1000 operations manual tascam tm-d1000 operations manual 2 note when referring to named parts of the tm- d1000, we will use the following typeface: ch sel (or ch sel in notes, etc.). When referring to words, etc. Shown on the display, we will use the following typeface: option . 1.2 tm-d1000...
Page 3
1 - tm-d1000 operations manual 3 tascam tm-d1000 operations manual warning although it is possible to connect equipment using the xlr and phone connectors at the same time to input channels 1 through 4, we do not recommend that you do this. There is a risk of damage to the microphone, due to sig- na...
Page 4
1 - tm-d1000 operations manual tascam tm-d1000 operations manual 4 1.3.10midi in & out these midi connectors are used for control by an external sequencer, etc., as well as for receiving midi timecode and transmitting midi machine control commands to external equipment. See “midi machine control” on...
Page 5: 2 - The Tm-D1000 Menu System
5 tascam tm-d1000 operations manual 2 - the tm-d1000 menu system the operational “heart” of the tm-d1000 is the menu system. Using this system, you can set up com- mon channel parameters, such as equalization, etc. And also the more general global settings, such as console configuration. The menu sy...
Page 6: 2 - The Tm-D1000 Menu System
2 - the tm-d1000 menu system tascam tm-d1000 operations manual 6 2.5 the display screen the display screen is typically used in the following way: the top line of the display screen is used to show the sub-menu or the parameter to be edited which is cur- rently selected. The right side of the top li...
Page 7: 2 - The Tm-D1000 Menu System
2 - the tm-d1000 menu system 7 tascam tm-d1000 operations manual to move the cursor around when editing names, press and hold down the data entry key while turning it. This allows you to change the position of the cursor (underlining the character position to be edited). Simply turn the knob without...
Page 8
Tascam tm-d1000 operations manual 8 3 - a quick guide to common functions this section gives you a brief “road map” of the common functions that you will need to perform dur- ing the course of a recording and mixdown session. ☞ initializing tm-d1000 internal data hold and press the param sel and ent...
Page 9
3 - a quick guide to common functions 9 tascam tm-d1000 operations manual ☞ recalling a snapshot press the escape/recall key until the display shows recall? . Choose the snapshot and press enter (see “recalling snapshots” on page 26.). ☞ storing a snapshot press and hold the shift key and press the ...
Page 10: 4 - Buss Functions
Tascam tm-d1000 operations manual 10 4 - buss functions as we mentioned briefly earlier, the busses of the tm-d1000 can be switched internally into different configurations, depending on the current needs of the project. These configurations may be stored in two conve- nient main user modes; the rec...
Page 11: 4 - Buss Functions
4 - buss functions 11 tascam tm-d1000 operations manual tors are assigned with one effector being used as a stereo processor for the stereo output buss, and the other effector used as another stereo processor assigned to the effect return. The param sel aux selection allows the channel to be routed ...
Page 12: 4 - Buss Functions
4 - buss functions tascam tm-d1000 operations manual 12 4.5 where do the busses go? As you can see from the above description, the l-r stereo buss is not used for recording in the rec modes. It goes straight out to the stereo outputs (analog or digital) and to the monitor buss (paral- leled to the h...
Page 13
13 tascam tm-d1000 operations manual 5 - using the digital inputs and outputs one of the main features of the tm-d1000 is its abil- ity to keep sound in the digital domain throughout the whole of a recording project, from digital source, through dtrs multitrack, etc., through to the final mix onto d...
Page 14
5 - using the digital inputs and outputs tascam tm-d1000 operations manual 14 5.3 connecting a 2-track recorder the tm-d1000 provides both xlr and rca con- nectors for output of the stereo busses. The format in which data can be output is either aes/ebu or spdif. Either format may be selected for ou...
Page 15
5 - using the digital inputs and outputs 15 tascam tm-d1000 operations manual 5 push the data entry knob to select the channel whose input you will be editing and turn the knob to select between the analog input and the digital input 1 . Note because the digital input is a stereo input, you will pro...
Page 16: 6 - Word Synchronization
Tascam tm-d1000 operations manual 16 6 - word synchronization when you have a digital audio setup, it is most important that all equipment in the setup shares the same word clock. This is not at all related to time- code synchronization, but refers to a digital signal at the sampling frequency which...
Page 17: 6 - Word Synchronization
6 - word synchronization 17 tascam tm-d1000 operations manual 3 turn the data entry knob until the bot- tom line of the display shows master clock select , and press enter : 4 use the data entry knob to choose the word clock source for the tm-d1000. The external word clock source may be the tdif-1 a...
Page 18: 7 - Channel Operations
Tascam tm-d1000 operations manual 18 7 - channel operations this covers most common channel operations (equalization, routing, etc.), as well as the channel dynamic processors. It does not cover aux sends and effects, which are described in “effects” on page 23. Fader operations are similar to those...
Page 19: 7 - Channel Operations
7 - channel operations 19 tascam tm-d1000 operations manual 7.3 using the direct outs the input channels can be sent to the tdif-1 outputs on a one-to-one basis instead of being routed through the group busses. Use the direct out key instead of the ch assign keys. Note the direct out facility is obv...
Page 20: 7 - Channel Operations
7 - channel operations tascam tm-d1000 operations manual 20 7.5 external insert points the tm-d1000 is capable of using external inserts on channels 1 through 4, as well as using its internal dynamic processors. Use standard ‘y’ cables such as tascam pw-4y or pw-2y cables to connect an external proc...
Page 21: 8 - Monitoring, Etc.
21 tascam tm-d1000 operations manual 8 - monitoring, etc. The tm-d1000 allows you to connect an amplifier/ speaker monitoring system to the monitor out connectors. The level of the signal transmitted from there is controlled by the level control. There is also a phones jack, into which you can plug ...
Page 22: 8 - Monitoring, Etc.
8 - monitoring, etc. Tascam tm-d1000 operations manual 22 mix as well as the monitor mix. If you are working in a sound reinforcement or mixdown application, you should take care not to use the in-place solo mode, as this will destroy the final mix. To select the solo mode: 1 press and hold down the...
Page 23: 9 - Effects
23 tascam tm-d1000 operations manual 9 - effects the tm-d1000 includes high-quality digital effects. There are three types of processor, and these can be patterned together in various ways, depending on the current mode and buss function selected. The processor types are: the patterns are: naturally...
Page 24: 9 - Effects
9 - effects tascam tm-d1000 operations manual 24 with the buss function, and n means that the effect pattern cannot be used with the buss function): 9.1 selecting effect patterns 1 press and hold down the shift key and press the option key to enter the option screen. 2 turn the data entry knob until...
Page 25: 9 - Effects
9 - effects 25 tascam tm-d1000 operations manual in some effect patterns, the effect type is fixed as a dynamic processor and cannot be changed. 1 press the param sel key until the effect/ dynamics indicator lights green. 2 push the data entry knob so that you select the correct effect screen (1 or ...
Page 26: 10 - Snapshots
Tascam tm-d1000 operations manual 26 10 - snapshots the settings of most of the parameters can be stored as a snapshot, which may be recalled manually, or under midi program change control. Snapshots 001 through 128 are available for storing settings. Snapshot 000 is a special case, where all “invis...
Page 27: 10 - Snapshots
10 - snapshots 27 tascam tm-d1000 operations manual 10.3renaming snapshots 1 press the escape/recall key until the current snapshot name and number is shown on the top of the display, and the word recall ? Is shown on the bottom. 2 push the data entry knob so that the bot- tom line reads rename : 3 ...
Page 28: 10 - Snapshots
10 - snapshots tascam tm-d1000 operations manual 28 1 press and hold down the escape/recall key and press the ch sel key whose channel number corresponds to the snapshot number that you want to recall. Only the first 16 user snapshots can be recalled in this way. Note if the direct recall defeat fea...
Page 29: 11 - Midi Machine Control
29 tascam tm-d1000 operations manual 11 - midi machine control the tm-d1000 can be used together with any recorder or other device that supports midi machine control commands, such as the tascam da-88 with the optional sy-88 synchronizer board, the tascam da-38 with the optional mmc-38, or the tasca...
Page 30: 11 - Midi Machine Control
11 - midi machine control tascam tm-d1000 operations manual 30 when the indicator is lit, the transport keys (the ch assign 1-2 , 3-4 and l-r keys, the eq key and the direct out key) take on the assignments printed in blue below these keys, and there is no need to press the shift key to use them as ...
Page 31: 11 - Midi Machine Control
11 - midi machine control 31 tascam tm-d1000 operations manual 11.6locating to a memory position locating to a memory position is done by holding down the shift key and pressing the ch sel key of the channel (location memory) to which you will be locating. 11.7editing a memory location 1 press the m...
Page 32
Tascam tm-d1000 operations manual 32 12 - midi control of the tm-d1000 snapshot changes may be carried out from a midi controller as program change messages. In addition, the two effect units and the four channel dynamic processor components of the tm-d1000 may also be set up to respond to program c...
Page 33
12 - midi control of the tm-d1000 33 tascam tm-d1000 operations manual unless otherwise stated, the 127 values available to a midi controller are interpreted and converted into the 100 parameter value steps used by the tm- d1000. 12.4system exclusive parameters and data dumps the tm-d1000 also provi...
Page 34: 13 - Options
Tascam tm-d1000 operations manual 34 13 - options a number of options are available for the tm- d1000, as described here. 13.1rm-d1000 rack mounting kit the rm-d1000 rack mounting kit allows the tm- d1000 to be mounted in 6u of rack space (in addi- tion to space needed at the top for the connectors)...
Page 35: 13 - Options
13 - options 35 tascam tm-d1000 operations manual channels 1 + 2 and 5 + 6, they will also be routed to the tdif-1 b channels with the same numbers. If input channels are routed using the direct out function, and the if-td1000 digital i/o board is fit- ted, the input channels will be output to the t...
Page 36: 14 - Miscellaneous Functions
Tascam tm-d1000 operations manual 36 14 - miscellaneous functions these functions help you with various settings of the tm-d1000. 14.1footswitch (remote cont) the footswitch connected to the rear of the tm- d1000 can be used to step through the snapshot memories, either forwards or backwards. It can...
Page 37: 14 - Miscellaneous Functions
14 - miscellaneous functions 37 tascam tm-d1000 operations manual have the battery replaced by your tascam distributor. Do not attempt to replace the bat- tery by yourself. You can also check the current battery level using the following procedure: option monitor ➠ system ➠ battery check if the disp...