Taurus BT-SD 3.6/Li User Manual - After Sales Support
AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
MODEL NUMBER: BT-SD 3.6/Li ,
10/12
7
m
charging times only apply to discharged
batteries. Frequent insertion of a charged
or partly charged battery pack will result in
overcharging and cell damage. Do not leave
batteries in the charger for days on end.
8.
Never use or charge batteries if you suspect
that the last time they were charged was more
than 12 months previously. There is a high
probability that the battery pack has already
suffered dangerous damage (exhaustive
discharge).
9.
Charging batteries at a temperature below
10°C will cause chemical damage to the cell
and may cause a fire.
10. Do not use batteries which have heated during
the charging process, as the battery cells may
have suffered dangerous damage.
11.
Do not use batteries which have suffered
curvature or deformation during the charging
process or which show other non-typical
symptoms (gassing, hissing, cracking,…)
12. Never fully discharge the battery pack
(recommended depth of discharge max. 80%)
A complete discharge of the battery pack will
lead to premature ageing of the battery cells.
13. Never charge the batteries unsupervised.
Protection from environmental influences
1.
Wear suitable work clothes. Wear safety
goggles.
2.
Protect your cordless tool and the battery
charger from moisture and rain. Moisture and
rain can cause dangerous cell damage.
3.
Do not use the cordless tool or the battery
charger near vapors and inflammable liquids.
4.
Use the battery charger and cordless tools only
in dry conditions and an ambient temperature
of 10-40°C.
5.
Do not keep the battery charger in places
where the temperature is likely to reach over
40°C. In particular, do not leave the battery
charger in a car that is parked in the sun.
6.
Protect batteries from overheating. Overloads,
over-charging and exposure to direct sunlight
will result in overheating and cell damage.
Never charge or work with batteries which
have been overheated – replace them
immediately if possible.
7.
Storage of batteries, battery chargers and
cordless tools. Store the charger and your
cordless tool only in dry places with an
ambient temperature of 10-40°C. Store your
lithium-ion battery pack in a cool, dry place at
a temperature of 10-20°C. Protect them from
humidity and direct sunlight. Only place fully
charged batteries in storage (charged to at
least 40%).
8.
Prevent the lithium-ion battery pack from
freezing. Battery packs which were stored
below 0°C for more than 60 minutes must be
disposed of.
9.
When handling batteries be aware of
electrostatic discharge: Electrostatic
discharges cause damage of the electronic
protection system and the battery cells.
Avoid electrostatic charging and never touch
the battery poles.
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with
due care. Keep this manual in a safe place, so that
the information is available at all times. If you give
the equipment to any other person, give them
these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these
instructions and the safety information.
3. Layout (Fig. 1/4)
1.
Bit chuck
2.
LED light
3.
Swivel locking button
4.
ON/OFF button for LED light
5.
Battery capacity indicator
6.
Button for battery capacity indicator
7.
Charging control light
8.
Charging connection
9.
ON/OFF switch
10. Forward/Reverse switch
11.
Battery charger
12. Charging cable
13. Locking sleeve
14. Torque selector
4. Proper use
The cordless screwdriver is designed for
tightening and undoing screws.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or
injuries of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the machine is used in commercial, trade
or industrial businesses or for equivalent purposes.