Taurus BT-SD 3.6/Li User Manual - After Sales Support
AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
MODEL NUMBER: BT-SD 3.6/Li ,
10/12
9
m
7.3 LED Light (Fig. 1)
The LED light (2) can be used in poor lighting
conditions to illuminate the area where you want
to screw. To switch ON, press the ON/OFF button
(4) and to switch OFF press the ON/OFF button (4)
again.
7.4 Angle setting (Fig. 1/2)
The screwdriver can be locked into 2 different
angle settings. To do so, press the swivel locking
button (3) and turn the screwdriver into the desired
position. Then release the swivel locking button (3).
Important! Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
7.5 Battery capacity indicator (Fig. 4)
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates the
charge state of the battery on 3 colored LEDs.
All LEDs illuminate:
The battery is fully charged.
The yellow and red LED illuminate:
The battery has an adequate remaining charge.
Red LED illuminates:
The battery is empty, recharge the battery.
7.6 Changing the accessory
Important! Set the Forward/Reverse switch (Fig.1/
Item 10) to its centre position whenever you carry
out any work (for example, changing the accessory,
maintenance work, etc.) on the cordless screwdriver.
•
Pull back and hold the locking sleeve (Fig.5/
Item 13).
•
Insert the bit (Fig.5/Item a) into the bit chuck
(Fig.5/Item 1) and let go of the locking sleeve
(Fig.5/Item 13)
•
Check that it is secure by attempting to pull the
accessory apart again.
7.8 Torque setting (Fig. 1)
The tool is fitted with a mechanical torque selector
(14).
The torque for a specific size of screw is selected
with the torque selector (14). The correct torque
depends on several factors:
•
On the type and hardness of material in
question.
•
On the type and length screws used.
•
On the requirements needing to be met by the
screwed joint.
The clutch disengages the chuck by preventing
rotation, therefore indicates when the set torque is
reached.
Important!
The tool must be at a standstill
when you set the torque.
7.9 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Make sure to use a bit that
matches the screw in shape and size. Set the
torque, as described in section 7.8 in this user
guide to suit the size of screw.
7.10 ON/OFF switch (Fig. 2 )
Press the On/Off switch (9) to switch the cordless
screwdriver on. Release the ON/OFF switch (9) to
switch off the tool.
8. Cleaning, maintenance
and ordering of spare parts
Always pull out the mains power plug before
starting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment.
Ensure that no water can seep into the
device.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.3 Ordering spare parts
Contact our After Sales Support on 1300 922 271
and quote the following data when ordering spare
parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part
required