Taurus RT-XS 28 Instruction Manual - 6. Operation
9
After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com
•
Place the rectangular sanding/grinding
plate (6) together with the fitted sanding/
grinding paper (a) onto the punch (9) for
the sanding/grinding paper). (Fig. 8)
•
Now punch the required holes into the
sanding/grinding paper.
•
Remove the punch (9) from the sanding/
grinding plate (6).
•
Check the correct position of the punch
holes in the sanding/grinding paper plate.
5.5.2 Fasting the sanding/grinding paper with
Velcro fastening system
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
extraction holes on the sanding/grinding paper
and the sanding/grinding disk are aligned.
5.6 Triangular sanding/grinding plate (Fig. 6)
Fit the triangular sanding/grinding plate (8) to
use the equipment as delta sander/grinder.
Fastening the sanding/grinding paper:
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
vacuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.7 Eccentric sanding/grinding plate (Fig. 6)
Fit the eccentric sanding/grinding plate (7) to
use the equipment as eccentric sander/grinder.
Fastening the sanding/grinding paper:
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the
vacuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
6. Operation
6.1 Switching the equipment ON/OFF
(Fig. 9/Item 2)
To switch on: Slide the ON/OFF switch (2)
forwards (position I)
To switch off: Slide the ON/OFF switch (2)
backwards (position 0)
6.2 Speed control (Fig. 7/Item 3)
To pre-select the speed turn the knurled screw
(3) on the switch.
Plus Direction:
High Speed
Minus Direction:
Lower Speed
5.2 Installing the dust extractor adapter
(Figure 2/Item 10)
Slip the dust extractor adapter (10) onto the
vacuum cleaner connector (a) as shown in Figure
2. Connect the dust extractor adapter to a
suitable dust extraction system.
Important.
For health safety reasons it is imperative that you
use a dust container or a dust extraction system.
5.3 Adjusting the additional handle (Fig. 3/4)
•
The additional handle engages in 4 positions
(90° steps).
•
Pull the additional handle upwards (1). (Fig.
3)
•
Turn the additional handle (1) into the
required working position. (Fig. 4)
•
Let go of the additional handle.
•
Ensure that the additional handle is securely
engaged in the required position.
5.4 Fitting/removing the sanding/grinding
plates (Fig. 5/6)
•
Use the Allen key (11) to remove the Allen
screw (a) and the washer (b) (Fig. 5).
•
Then remove the sanding/grinding plate (c)
(Fig. 5).
•
To assemble, proceed in reverse order.
•
When fitting the sanding/grinding plate
(6 / 8) make sure that the 4 rubber stoppers
(d) are inserted into the corresponding
mounts (e). (Fig. 6)
•
Check that the sanding/grinding plate is
secure.
5.5 Rectangular sanding/grinding plate
(Fig. 6/7/8)
Fit the rectangular sanding/grinding plate (6) to
use the equipment as an orbital sander/grinder.
5.5.1 Fasting the sanding/grinding paper with a
clamping system)
Use of sanding/grinding paper with the
corresponding dimensions and perforations (Fig.
7):
•
Press the lever (a) upwards.
•
Insert the sanding/grinding paper (b) into
the open clamp and close the clamp.
•
Lay the sanding/paper over the oscillating
plate so that the paper is taut and clamp it
again.
•
Make sure that the perforations in the
sanding/grinding paper coincide with the
oscillating plate.
Use of sanding/grinding paper without the
appropriate dimensions and perforations (Fig.
7/8):
•
Cut the sanding/grinding paper to fit the
corresponding dimensions.
•
Fit the sanding/grinding paper to the
sanding/grinding plate as described above.