1. DL manuals
  2. Taylor
  3. Freezer
  4. 390
  5. Operating Instructions Manual

Taylor 390 Operating Instructions Manual

Other manuals for 390: Operator's Manual, Service Manual
Manual is about: Slush Freezer

Summary of 390

  • Page 1

    Model 390 slush freezer operating instructions 048693-m 6/01.

  • Page 2

    Complete this page for quick reference when service is required: taylor distributor: address: phone: service: parts: date of installation: information found on the data label: model number: serial number: electrical specs: voltage cycle phase maximum fuse size: a minimum wire ampacity: a e june, 200...

  • Page 3: Table Of Contents

    Table of contents model 390 table of contents section 1 to the installer page 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water connections page 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air cooled units page 1...

  • Page 4

    Model 390 table of contents notes:.

  • Page 5: Section 1

    1 model 390 to the installer 040419 section 1 to the installer this machine is designed for indoor use only. Do not install the machine in an area where a water jet could be used. Failure to follow this instruction may result in serious electrical shock. Water connections (water cooled units only) a...

  • Page 6: Section 2

    2 models 383 & 384 to the operator 050906 section 2 to the operator the slush freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The taylor equipment, when properly operated and cared for, will produce a consistent quality product. Like all me...

  • Page 7: Section 3

    3 model 390 safety 040419 section 3 safety we at taylor company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built-in safety features to protect both you and the service tec...

  • Page 8: Section 4

    4 model 390 operator parts identification section 4 operator parts identification item description part number 1 hopper cover x38458 2 gasket--hopper cover 038375 3 feed tube 015176-9 4 drip pan 035034 5 splash shield 046177 6 drip tray 046275.

  • Page 9

    5 model 390 operator parts identification beater assembly item description part number 1 freezer door x47982 2 gasket-door 014030 3 front bearing 013116 4 o-ring--baffle 018550 5 baffle arm 047729 6 baffle x47731 7 guide bearing 014496 8 beater x46233 9 scraper blade 046237 10 clip-scraper blade 046...

  • Page 10: Section 5

    6 model 390 important: to the operator section 5 important: to the operator control switch the center position is “off”. The “wash” position activates the beater motor only. The “auto” position allows the beater motor and compressor to run. Indicator light -- “mix low” located on the front of the ma...

  • Page 11: Section 6

    7 model 390 operating procedures section 6 operating procedures following are step-by-step operating procedures for the model 390 slush freezer. This unit has a 20 quart (18.9 liter) mix hopper and the freezing cylinder holds 7 quarts (6.6 liters) of slush product. We begin our instructions at the p...

  • Page 12

    8 model 390 operating procedures step 5 install the freezer door. Place the front end of the baffle into the hole in the center of the door. Position the door onto the four studs on the front of the freezing cylinder and push the door into place. Install the four handscrews onto the studs and tighte...

  • Page 13

    9 model 390 operating procedures closing procedures to disassemble the model 390, the following items will be needed: s two cleaning pails s sanitized stainless steel rerun can with lid s necessary brushes (provided with freezer) s cleaner s single service towels draining product from the freezing c...

  • Page 14

    10 model 390 operating procedures cleaning step 1 prepare two gallons (7.6 liters) of an approved cleaning solution (example: kay-5 r ). Use warm water and follow the manufacturer’s specifications. Step 2 pour the two gallons (7.6 liters) of cleaning solution into the hopper and allow it to flow int...

  • Page 15

    11 model 390 operating procedures brush cleaning step 1 prepare a sink with an approved cleaning solution (example: kay-5 r ). Use warm water and fol- low the manufacturer’s specifications. (if another approved cleaner is used, dilute according to label instructions.) important: follow label directi...

  • Page 16: Section 7

    12 model 390 operating procedures section 7 important: operator checklist during cleaning and sanitizing cleaning and sanitizing schedules are governed by your state or local regulatory agencies and must be followed accordingly. The following check points should be stressed during the cleaning and s...

  • Page 17

    13 model 390 operating procedures winter storage if the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is to be left unheated and subject to freezing conditions. Disconnect the freezer ...

  • Page 18: Section 8

    14 model 390 operating procedures section 8 troubleshooting guide problem probable cause remedy page ref. 1. No product being dispensed with draw valve opened. A. Improper mixing of product. A. Carefully follow directions for mixing product. ---- b. Mix low condition. B. Add mix to mix hopper. 6 2. ...

  • Page 19

    15 model 390 operating procedures problem probable cause remedy page ref. 7. No freezer operation with unit in the “auto” position. A. Unit unplugged. A. Plug cord in wall receptacle. ---- b. Beater motor has tripped the internal overload. B. Place control switch in the “off” position. Allow the mot...

  • Page 20: Section 9

    16 model 390 operating procedures section 9 parts replacement schedule part description every 3 months every 6 months annually drive shaft o-ring x drive shaft seal x scraper blade inspect & replace if necessary minimum baffle o-ring x guide bearing x freezer door gasket x front bearing x draw valve...

  • Page 21: Section 10

    Section 10 parts list 17 + available separately model 390 parts list c o p e lan d c o m p re sso r - j8086700/u p (u p d a te 134) de s cri p t io n p art numbe r qt y. Warr. Clas s re marks p art s up da t e arm -baffle *390* 047729 1 103 j4040000/ up 83 baffle assembly x47731 1 103 j4040000/ up 8...

  • Page 22

    + available separately 18 parts list model 390 de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r co ndenser -a c -15lx14hx2. 59t -3 rw 046558 1 103 coupli ng a. -t orque -shake -h ex x48316 1 103 coupli ng -t orque -dri ve 046866 1 103 coupli ng -t orque -load -h ex 03939...

  • Page 23

    19 + available separately model 390 parts list 020624 de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r o -ri ng -. 291 id x .080w 018550 1 000 baffle assembly o -ri ng -7 /8 o d x .139w 025307 1 000 dri ve shaft o -ri ng -1 ”o d x .139w 032504 2 000 draw valve seal -dri ...

  • Page 24

    + available separately 20 parts list model 390 020624 de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r panel -s id e *390* ri g h t 047007 1 103 + w asher -p lasti c pi vot 013808 2 000 + s crew -1/ 4 -20x3/ 8 rhm -s tnls 011694 3 000 panel -s id e u pper ri ght (new ) 0...

  • Page 25

    21 + available separately model 390 parts list de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r + o -r in g -7/ 8 o d x .139w 025307 1 000 + seal -dri ve shaft 032560 1 000 shell a .- in sulated *390* x46984 1 512 + s tud -no se co ne -5 /1 6 -18x5/ 16 -1 8 013496 4 103 ...

  • Page 26

    + available separately 22 parts list model 390 de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r wa te r c oole d condenser -w c -spi ral 049309 1 103 m o tor -fan 9 w a tt 012768 -2 7 1 103 fan -5 b lade 016289 1 103 sw it ch -p ressure 048231 1 103 valve -w ater 046686 ...

  • Page 27

    23 + available separately model 390 parts list de s cri p t io n p art s up da t e re marks warr. Clas s qt y. P art numbe r beari n g -gui d e 014496 1 000 o -ri ng .291 id x .080w 018550 1 000 baffle assembly o -ri ng -7 /8 o d x .139w 025307 1 000 dri ve shaft o -ri ng -1 ” o d x .139w 032504 2 0...

  • Page 28: Section 11

    Section 11 wiring diagrams 047730--27 rev. 8/02.

  • Page 29

    047730--33 rev. 8/02.