1. DL manuals
  2. Taylor
  3. Commercial Food Equipment
  4. C119 05
  5. Use And Maintenance Manual

Taylor C119 05 Use And Maintenance Manual

Manual is about: ELECTRONIC HORIZONTAL BATCH FREEZER

Summary of C119 05

  • Page 1

    Manuale d’uso e manutenzione manual of use and maintenance manuel d’utilisation et d’entretien gebrauchsanweisung und wartungshandbuch manual de uso y manutencion mantecatori orizzontali elettronici electronic horizontal batch freezer turbines Électroniques horizontales elektronische waagrechte spei...

  • Page 2

    1 - english.

  • Page 3

    English - 2 the machine is covered by guarantee according to the conditions reported in the “guarantee card “ enclosed to the machine, which shall be duly filled up and sent back to: frigomat s.R.L., via 1° maggio 26862 guardamiglio (lodi) – italia in the following field, please write your machine s...

  • Page 4

    3 - english congratulations on purchasing a machine taylor. The present manual, enclosed to the machine, is integrant and essential part of the machine and shall be delivered to the final user. Before performing any kind of operation, it is recommended to carefully study the reported instructions, a...

  • Page 5

    English - 4 1 transport, handling and storage. 1.1 preliminary inspection the machine travels at the customer’s risk. In case packing is damaged, immediately inform the carrier. Immediately inform the carrier also in case of damage to the machine, even if you open the packing a few days after the de...

  • Page 6

    5 - english 2. Markings and graphics never touch the machine with hands and tools during production or maintenance and cleaning operations, without making sure that the machine is in stop position, the master switch is off and/or the multipolar plug disconnected. Taylor declines any liability for ac...

  • Page 7

    English - 6 warning! Do not touch with hands. The following plate placed on the back of air-cooled machines shows that cleaning operations on the heat exchanger shall be carried out only by means of a brush or an exhauster. Warning! High voltage inside, danger of fulguration. The following plate is ...

  • Page 8

    7 - english 3. Installation 3.1 field of use the batch freezers series c are espressly designed and engineered for ice-cream batch freezing cycles. 3.2 limits of use never use the machine with variable supply voltage and/or more than +/- 10% of the value showed in the nameplate or when the feeder is...

  • Page 9

    English - 8 attempts and far from liquids, water and heat sources. It shall not be damaged, otherwise make it be replaced by qualified personnel with another section and type 5g4 h07rn-f (for version 400 v), 4g4 h07rn-f (for version 230/3 v) or 3g4 h07rn- f (for version 230/1 v) before connecting th...

  • Page 10

    9 - english • for three-phase versions only, check the correct direction of rotation of the agitator motor: apply voltage to the machine, press delivery pushbutton and check that the agitator direction of rotation is counterclockwise through the hopper grid. If not, exchange the wires in the feeder ...

  • Page 11

    English - 10 4. Safety devices shearing prevention system: realized by means of a no micro-switch in conformity with the european standard; it stops the machine when the door is opened and/or the grid on the hopper is lifted and visualize eme on the display. Beater motor safety system: it consists o...

  • Page 12

    11 - english 5. Operation 5.1 controls 1. Door it hermetically seals the cylinder during the working cycles. It can be easily removed for cleaning purpose. 2. Safety grid – hopper cover it allows the operator to charge the product under safe conditions. The cover prevents the batch to get in contact...

  • Page 13

    English - 12 5.2 control panel 1. Display it displays all information about the working processes and the allowed settings. 2. Ter led it warns about any malfunction in the system 3. Stop whatever working cycle is in progress, it stops the machine and cancels any function in progress. 4. Delivery/ u...

  • Page 14

    13 - english 5.3 gelato and granita production after the machine has been installed according to the instructions reported in chapter 3 and carefully cleaned and sanitized according to the instructions reported in chapter 6, proceed as follows to start up the ice-cream production: - check that the m...

  • Page 15

    English - 14 5.3.1 gelato production with consistency control - by pressing the semi-automatic production pushbutton, the display lightens indicating the last consistency setting. Pushbuttons up – enter – down lighten as well. Now the machine is ready to enter a new gelato consistency setting. If af...

  • Page 16

    15 - english 5.3.2 gelato production with time control - by pressing the time production pushbutton the display lightens, indicating the last time setting. Pushbuttons up – enter – down lighten as well. Now the machine is ready to enter a new duration time of the freezing cycle. If after 5 seconds n...

  • Page 17

    English - 16 5.3.3 granita production gr1 granita cycle here it is possible to set and program the consistency values, exactly as the ice cream semi-automatic production cycle. - by the press of the granita pushbutton both the display – showing gr1 – and up- enter-down pushbuttons lighten. Now the m...

  • Page 18

    17 - english 6. Maintenance 6.1 routine maintenance (addressed to the user) during production, cleaning and maintenance operations, never touch the machine with hands or tools without making sure that the machine has been disconnected from mains. In case of troubles, make sure that they are not caus...

  • Page 19

    English - 18 6. For models modello c122 turn the two knobs outwards, seize the bent lever and pull it to remove the door. 7. Dismantle the door into pieces: • unscrew the handle adjusting knob • remove the handle • remove the delivery door and the spring • draw the or rings out 8. Pull the agitator ...

  • Page 20

    19 - english 6.1.2 maintenance of agitator and gaskets the agitator blades are equipped with scraping pads made of atoxic plastic materials suitable for food industry. These components are subject to wear according to the characteristics of the employed mixture: with high sugar content and low fat p...

  • Page 21

    English - 20 6.2 extraordinary maintenance (for qualified personnel) these operations shall be carried out by qualified and authorized personnel only. Taylor declines any liability for damages to things or persons deriving from the non-observance of the above-mentioned prescription. The parameters o...

  • Page 22

    21 - english “meb-new” card programming table (*) step description min max c119 c122 step t1 amplification ta high consistency (ice cream ) 0.5 3.0 1,5 1 0.1 nr t2 amplification ta low consistency (sherbet) 0.5 3.0 2 0,8 0.1 nr t3 hz selection 0 1 0 0 0=50 hz 1=60 hz t4 hysteresis 1 10 5 8 1% set t5...

  • Page 23

    English - 22 follow the instructions below to perform the consistency calibration: 1. Make sure that the master switch is off and/or the multipolar plug is disconnected. 2. Remove the right side panel (c119) or back panel (c122) and the electrical box cover. 3. Find the current transformer power wir...

  • Page 24: Ter

    23 - english 7 trouble-shooting 7.1 alarms management the “meb-new” electronic card is a powerful control logic unit which signals possible machine troubles by means of alphanumeric messages visualized on the display; the technician shall understand them to quickly find the reason of this trouble. M...

  • Page 25

    English - 24 7.2 troubleshooting trouble possible causes remedies electric trouble or failed safety micro switch call a qualified technician the machine does not start up (stop pushbutton on without active alarms) incorrect power supply check the phases. Master switch off or incorrect power supply c...