Owner’s manual 1111 w. 35th street • chicago, il 60609 usa customer support: (773) 869-1234 • application services: (773) 869-1236 www.Tripplite.Com copyright ©2002 tripp lite. All rights reserved. Smartonline ™ tower/rackmount power protection su6000rt3upm • su10krt3upm tower/rackmount ups systems ...
2 important safety warnings save these instructions. This manual contains important instructions and warnings that should be followed during the installation and maintenance of all tripp lite smartonline rackmount ups systems and their batteries. Ups location warnings • install your ups indoors, awa...
3 mounting 1 single unit installation 1 2 3 a b c b e d f 4 g connect the two segments of each shelf (a) using the included screws and nuts (b). Leave the screws slightly loose so that the shelves can be adjusted in the next step. Adjust each shelf to fit your rack, then mount them in the lowest ava...
4 mounting continued connect the shelved sections from two upsrmrii kits (a) to the unshelved sections (b) using the included screws and nuts (c). Note: two unshelved sections will be left over. Leave the screws slightly loose so that the shelves can be adjusted in the next step. Adjust each shelf t...
Mount the shelved sections (a) of your upsrmrii kit on the back side of your rack. Mount them in the lowest available space of your rack with with the screws, nuts and washers provided (b). Note that the support ledges should face inward. Attach mounting ears (c) to the front mounting holes of your ...
6 features familiarize yourself with the location and function of the front and rear panel features before installing and operating your ups. Ups front panel controls the ups front panel controls can be rotated in its mounting to match your tower or rackmount installation. To rotate the controls, in...
7 features continued ups rear panel epo acc. Rs-232 dry contact ac input ac output breaker ac input breaker external battery input 240vdc caution: do not disconnect under load g l1 l2 l2 l1 g g l1 l2 l2 l1 g ac output c us ul input: 200/208/220/230/240v~, 50/60hz 29.1/27.9/26.4/25.3/24.2a output: 20...
8 features continued ups rear panel 1. Output terminal block: use these terminals to connect your ups to your equipment or to the transformer’s ups connector. Unscrew and remove the cover plate above the block for access. 2. Input terminal block: use these terminals to connect your ups to your utili...
9 hardwire your utility power source to your ups’s input. Remove the top of the box covering the ups’s power terminals. Pass one end of a power cable through the ups’s cover box’s right knockout, then connect it to the ups’s input terminals. Connect the other end to your utility power source. Hardwi...
10 normal by pass hardwire your isolation transformer’s ups connector to your ups’s input and output. Remove the tops of the boxes covering the ups’s and transformer’s input and output terminals. Pass the free end of the isolation transformer’s ups connector through the ups’s cover box’s knockout, t...
11 connection continued connect external battery pack(s) to your ups your ups has no internal batteries and must be connected to at least one external battery pack to operate. Complete installation and mounting instructions for your battery pack(s) appear in the battery pack(s)’s owner’s manual. Mak...
12 turn input to the ups on if the ups is connected to a transformer, turn the transformer’s ups and load breakers on. Turn the ups’s input circuit breaker on. Press the ups’s on button until you hear a beep to begin inverter operation. If your ac input is not providing power normally, you may “cold...
13 diagnostic mode ac/dc ok diagnostic mode testing inverter on battery mode load = xxx% x.Xxkw operation when you turn the ups on, it will enter diagnostic mode and perform a brief self-test lasting about 15 seconds. The results of the self-test are shown on the lcd screen in the sequence below. Di...
14 operation continued during normal operation, the first line of your lcd display shows which operating mode your ups is in: online, economy, on battery, or bypass. Online mode: the ups provides ac power while utility power is available and switches to on battery mode instantly (zero transfer time)...
15 operation continued while in bypass mode, the ups monitors its input voltage and passes that input power along to connected equipment. The ups will not provide battery backup in bypass mode. If the output voltage deviates from an acceptable range (between 15% higher and 20% lower than nominal), t...
16 service/warranty and insurance your smartonline ups is covered by the 2-year limited warranty period described below. A variety of service contracts is also available from tripp lite, including start-up service contracts and 3- to 5-year safesure on-site service contracts. For more information, c...
17 specifications specifications are for ups, isolation transformer, and one battery pack. Model su6000rt3u su10krt3u input ups input voltage 156v~276v single phase 156v~276v single phase transformer input voltage 200/208/220/230/240v 200/208/220/230/240v input frequency 50/60 hz ± 3 hz 50/60 hz ± 3...
