VADDIO RoboSHOT 12 HDMI Installation And User Manual - page 10
RoboSHOT HDMI Series Cameras
RoboSHOT HDMI Series Camera Manual - Document Number 342-1001 Rev A
Page 10 of 40
R
OBO
SHOT
HDMI
S
WITCH
S
ETTINGS
The RoboSHOT cameras control the resolution of the video signal. There is, as explained on the page 10, a rotary
switch to set the HD video resolution and a set of eight (8) DIP switches that determine certain camera functions.
See drawing and Description on how to setup the camera.
Drawing: DIP Switch and Resolution Label on the Bottom of the RoboSHOT
Setting the RoboSHOT Switch Gear:
①
-
Set the desired available HD output resolution for the camera with the Rotary Switch.
②
-
Set the IR control frequency of the camera if it is to respond to the IR remote control.
③
-
If using the IR forwarding features with a 3
rd
party codec IR remote, set the IR OUT switch to ON (SW3).
④
-
If inverting the camera, turn the IMAGE FLIP ON (SW4).
⑤
-
For the RoboSHOT 12X model only, set the Super-wide mode to ON for a 12X, 73º horizontal super-wide angle
of view. Normal mode will produce 67.2º horizontal field of view (HFOV). The RoboSHOT 30 does not have a
Super Wide mode.
⑥
-
Set the Baud Rate DIP switch (SW6) to 9600bps for most applications. Default is 9600 bps systems.
⑦
-
Set the color space for HDMI (YCbCr) or for DVI-D (sRGB).
⑧
-
Setting all DIP switches DOWN with a power cycle loads the default camera settings. Return DIPs to desired
operating position after power cycle
.
Note: Switch 8 is reserved for future use.
DIP Switch Settings Further Explained (DSSFE):
IR 1, 2 and 3 (SW 1 &2): A single IR remote has the capability of operating up to three different PTZ cameras
in a room. Use these selector DIP switches and the selector buttons at the top of the IR remote to select the
frequency.
IR OUT on/off (SW3): The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning
on the IR output will allow IR signals to be transmitted over the Cat-5 cable to the head end.
Image Flip (SW4): To invert the camera, turn the IMAGE FLIP ON (switch down).
Super-Wide Mode: Super-wide works only with the RoboSHOT 12 model and allows the camera to switch from
67.3º wide end HFOV to a Super Wide 73º wide end HFOV.
Baud Rate (SW6): The options for baud rate are either 9600 or 38,400 bps. The 9600 bps works best with Cat-
5e over distance. Use 38,400 bps for short control lines only.
DIP Switches (SW7 & 8): Not used for operation, please leave these DIP switches up or in the OFF position.
IR 1
1 & 2 UP
ON
DIP SWITCH SETTINGS
8
1
2
3
4
5
6
7
HD VIDEO RESOLUTION SELECT
720p/59.94
1080i/59.94
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1080p/59.94
1080i/60
1080p/60
720p/50
2
1
5
4
3
7
6
8
IR 2
ON
IR 3
ON
IR
OUT
OFF
BAUD
9600
bps
38,400
bps
1080i/50
1080p/50
HDMI
COLOR
YCbCr
8
OFF
IMAGE
FLIP
OF
F
ON
SUPER
WIDE
OFF
ON
720p/60
1080p/30
1080p/25
sRGB
COLOR
②
①
③ ④ ⑤ ⑥ ⑦
All Down
with Power
Cycle for
Defaults
⑧