1. DL manuals
  2. Valentin
  3. Printer
  4. Compa II Series
  5. Operating Manual

Valentin Compa II Series Operating Manual

Other manuals for Compa II Series: Operating Manual

Summary of Compa II Series

  • Page 1

    Compa ii operating manual.

  • Page 2

    Copyright by carl valentin gmbh / 7952005b.0715 information on the scope of delivery, appearance, performance, dimensions and weight reflect our knowledge at the time of printing. We reserve the rights to make modifications. All rights, including those regarding the translation, are reserved. No par...

  • Page 3

    Compa ii series table of contents 07.15 operating manual 3 table of contents table of contents .............................................................................. 3 1 important notes ..................................................................... 5 1.1 intended use ....................

  • Page 4

    Table of contents compa ii series 4 operating manual 07.15 9 maintenance and cleaning .................................................. 81 9.1 general cleaning ................................................................... 82 9.2 cleaning the printer roller .......................................

  • Page 5

    Compa ii series important notes 07.15 operating manual 5 1 important notes the label printer can be used in thermal as well as in thermal transfer applications. The label printer is equipped with 8 vector, 6 bitmap and 6 proportional fonts. It can be printed inverse, in italic format or 90 degrees t...

  • Page 6

    Important notes compa ii series 6 operating manual 07.15 1.2 environmentally-friendly disposal manufacturers of b2b equipment are obliged to take back and dispose of old equipment that was manufactured after 13 august 2005. As a principle, this old equipment may not be delivered to communal collecti...

  • Page 7

    Compa ii series important notes 07.15 operating manual 7 figure 2 0 1 = adjusting screw for transfer ribbon regulating shaft 0 2 = transfer ribbon for regulating shaft 0 3 = printhead lock 0 4 = printhead 0 5 = label material guiding 0 6 = return pulley 0 7 = printer roller 0 8 = label photocell han...

  • Page 8

    Important notes compa ii series 8 operating manual 07.15 figure 3 1 = switch on/off 2 = power supply 3 = plug-in for cf card 4 = usb interface 5 = serial interface rs-232 6 = ethernet 10/100 interface 7 = usb host for usb keyboard and usb memory stick 8 = parallel interface for centronics 9 = extern...

  • Page 9

    Compa ii series safety notes 07.15 operating manual 9 2 safety notes the printer is designed for power supply systems from 110-230 v. Connect the label printer only to electrical outlets with a ground contact. Couple the label printer to devices using extra low voltage only. Before making or undoing...

  • Page 10

    Safety notes compa ii series 10 operating manual 07.15 2.2 operating conditions before initial operation and during operation these operating conditions have to be observed to guarantee save and interference-free service of our printers. Therefore please carefully read these operating conditions. Sh...

  • Page 11

    Compa ii series safety notes 07.15 operating manual 11 the installation of the power supply to connect our printers has to be effected according to the international rules and regulations, especially the recommendations of one of the three following commissions: international electronic commission (...

  • Page 12

    Safety notes compa ii series 12 operating manual 07.15 immunity to interference according to en 61000-6-2: 2005 industrial sector stray radiation against discharge of static electricity according to en 61000-4-2: 12-2001 electromagnetic fields according to en 61000-4-3: 11-2003, env 50204: 03-1995 f...

  • Page 13

    Compa ii series safety notes 07.15 operating manual 13 to avoid inadmissible heating, free air convection has to be ensured. Protection according ip: 20 ambient temperature °c (operation): min. +5 max. +35 ambient temperature °c (storage): min. −20 max. +60 relative air humidity % (operation): max. ...

  • Page 15

    Compa ii series technical data 07.15 operating manual 15 3 technical data compa ii 103/8 t compa ii 104/8 compa ii 106/12 compa ii 106/24 compa ii 108/12 t compa ii 162/12 compa ii 162/12 t print resolution 203 dpi 203 dpi 300 dpi 600 dpi 300 dpi 300 dpi 300 dpi max. Print speed 200 mm/s 200 mm/s 20...

  • Page 16

    Technical data compa ii series 16 operating manual 07.15 operation panel compa ii 103/8 t compa ii 104/8 compa ii 106/12 compa ii 106/24 compa ii 108/12 t compa ii 162/12 compa ii 162/12 t keys test print, function menu, quantity, cf card, feed, enter, 4 x cursor lcd display graphic display 132 x 64...

  • Page 17

    Compa ii series technical data 07.15 operating manual 17 tear-off edge real time clock with printout date and time automatic daylight saving time storage of data with shut-down variables: link field, counter, date/time, currency and shift variable, cf data integrated unwinder (max. Outer diameter 18...

  • Page 18

    Technical data compa ii series 18 operating manual 07.15 3.1 control inputs and outputs by means of a maximum of 16 control inputs and outputs which, in the following, are also referred to as ports, different functions of the printer system can be triggered and operating states can be displayed. The...

  • Page 19

    Compa ii series technical data 07.15 operating manual 19 figure 5 port 1 to port 16 = assignment for i/o profile 'std_label' identification pin description / function port 1 10 print start and cut (input) port 2 1 reprint last printed label (input) port 3 11 counter reset (input) port 4 2 option app...

  • Page 20

    Technical data compa ii series 20 operating manual 07.15 identification pin description / function + 5 vdc ext 25 5 volt dc output for external use. Max. 1 a. This voltage is provided from direct print module and can be used e.G. As control voltage. Never apply any external voltage to this output. +...

  • Page 21

    Compa ii series technical data 07.15 operating manual 21 device connection to a machine with s7-300 sps. Figure 6 device connection to a operating panel. Figure 7 example 1 example 2.

  • Page 22

    Technical data compa ii series 22 operating manual 07.15 device connection version if 'option: 2. Led'. Figure 8 when connecting a reed contact with a control input, the contact must have a switching capacity of min. 1 a in order to prevent the contact from sticking due to the inrush current. As an ...

  • Page 23

    Compa ii series technical data 07.15 operating manual 23 3.2 plug & play plug & play capable printers can be recognised automatically at parallel ports, usb-ieee 1394- or infra-red connections but the last both are not important for our printers. The following table shows the plug & play capability ...

  • Page 25

    Compa ii series installation 07.15 operating manual 25 4 installation lift the label printer out of the box. Check the label printer for transport damages. Check delivery for completeness. Label printer. Power cable. Empty core, mounted on transfer ribbon rewinder. Tear-off edge (basic printers only...

  • Page 26

    Installation compa ii series 26 operating manual 07.15 4.2 connecting the label printer the label printer is equipped with a versatile power supply unit. The device may be operated with a mains voltage of 110-230 v / 50-60 hz without any adjustments or modifications. Caution! The label printer can b...

  • Page 27

    Compa ii series installation 07.15 operating manual 27 4.4 initiation of the label printer after switching on the label printer the main menu appears which shows the printer type, current date and time. Insert label material and transfer ribbon (see chapter 5. Loading media, page 29). Go to menu lab...

  • Page 29

    Compa ii series loading media 07.15 operating manual 29 5 loading media notice! For adjustments and simple installation work, use the accompanying hexagonal wrench located in the bottom section of the print unit. No other tools are required for the work described here. 5.1 loading label roll notice!...

  • Page 30

    Loading media compa ii series 30 operating manual 07.15 1. Turn lever (5) counter clockwise to lift up the printhead. 2. Push label guiding on deviating shaft (4) all the way out. 3. Guide label material below the deviating shaft (4) and the label photocell so it leaves the print unit between printh...

  • Page 31

    Compa ii series loading media 07.15 operating manual 31 figure 11 in rewind mode the labels are wound up internally after printing for later use. 1. Guide label strip around the deviating shaft (4) to the internal rewinder (2). 2. Hold rewinder (2) firmly and turn knob (3) clockwise until it stops. ...

  • Page 32

    Loading media compa ii series 32 operating manual 07.15 figure 12 1. Loosen knurled screw (1), turn guiding (2) upwards and move it to the outside as far as possible. 2. Insert label roll on the roll holder so you can see the side from above which can be printed on. 3. Unwind a longer label strip: f...

  • Page 33

    Compa ii series loading media 07.15 operating manual 33 figure 13 in dispensing mode the labels are removed after printing, and only the liner is wound up internally. 1. Lift up pinch roller (4) off the deviating shaft (5). 2. Remove labels from the first 100 mm of the backing paper. 3. Guide liner ...

  • Page 34

    Loading media compa ii series 34 operating manual 07.15 the printhead is pushed on via two plungers (1). The location of the right plunger must be set to the width of the label medium used so as to: achieve even print quality across the entire label width, prevent wrinkles in the feed path of the tr...

  • Page 35

    Compa ii series loading media 07.15 operating manual 35 5.2 removing wound roll figure 15 1. Turn lever (5) anticlockwise to lift up printhead. 2. Cut label strip and wind it fully around the rewinder (2). 3. Hold rewinder (2) firmly and turn knob (3) clockwise. The rewinder spindle relaxes and the ...

  • Page 36

    Loading media compa ii series 36 operating manual 07.15 5.3 loading fanfold labels figure 16 1. Loosen knurled screw (1) and slide guiding (2) outward completely and swivel it downward past the roll retainer (3). 2. If core adapters are mounted on the roll retainer (3), remove core adapters. 3. Posi...

  • Page 37

    Compa ii series loading media 07.15 operating manual 37 5.4 loading transfer ribbon notice! For the thermal transfer printing method it is necessary to load a ribbon, otherwise when using the printer in direct thermal print it is not necessary to load a ribbon. The ribbons used in the printer have t...

  • Page 38

    Loading media compa ii series 38 operating manual 07.15 7. Turn transfer ribbon rewinder (1) counter clockwise to smooth out the feed path of the transfer ribbon. 8. Turn lever (4) clockwise to lock the printhead. Notice! As for the electrostatic unloading the thin coating of the thermal printhead o...

  • Page 39

    Compa ii series loading media 07.15 operating manual 39 5.6 removing and/or installing rewind guide plate removing and/or installing rewind guide plate, dispenser edge or tear-off edge to convert the printer for use in another operating mode, a rewind guide plate, a peel off plate or a tear-off plat...

  • Page 41

    Compa ii series function menu 07.15 operating manual 41 6 function menu 6.1 operation panel 1 the top line of the graphic display shows the printer type. 2 the graphic display shows information about the current status of the printer and the print order, reports errors and shows the printer settings...

  • Page 42

    Function menu compa ii series 42 operating manual 07.15 6.2 menu structure speed contrast ribbon control y offset x offset tear-off offset print settings label length gap length column printing measure label label type material selection photocell scan position label error length synchronisation fli...

  • Page 43

    Compa ii series function menu 07.15 operating manual 43 operating modes double cut cutter control cutter (option) automatic return operating modes i/o port 1-8 i/o port 9-16 i/o protocol save signal dispenser i/o (option) io profile operating modes debounce start signal delay operating modes applica...

  • Page 44

    Function menu compa ii series 44 operating manual 07.15 status ip address netmask gateway dhcp wlan (option) port interval remote console com1 baud parity data bits stop bit interface start sign stop sign data memory port test protocol printhead resolution drive mapping emulation set date/time summe...

  • Page 45

    Compa ii series function menu 07.15 operating manual 45 label parameters photocell settings photocell/sensors paper counter heater resistance printhead temperature motor ramp print examples input/output online/offline transfer ribbon prior warning zero point adjustment print length +/- service funct...

  • Page 46

    Function menu compa ii series 46 operating manual 07.15 6.3 print settings switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key to select the menu print settings. Indication of print speed in mm/s (see chapter technical data, page 15). The...

  • Page 47

    Compa ii series function menu 07.15 operating manual 47 6.4 label layout switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the label layout menu. Press key to select the menu. Indication of label length in mm (see ...

  • Page 48

    Function menu compa ii series 48 operating manual 07.15 press key to arrive the next menu item. In case an error occurs, indication after how many mm a message appears in the display. Value range:1 mm … 999 mm. On: if a label is missed on the liner an error message is displayed. Off: missing labels ...

  • Page 49

    Compa ii series function menu 07.15 operating manual 49 6.5 device settings switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the device settings menu. Press key to select the menu. Off: the complete print memory i...

  • Page 50

    Function menu compa ii series 50 operating manual 07.15 press key to arrive the next menu item. On: an acoustic signal is audible when pressing a key. On: value range: 1 … 7. Off: no signal is audible. Setting of display contrast. Value range: 35 … 85. Press key to arrive the next menu item. Selecti...

  • Page 51

    Compa ii series function menu 07.15 operating manual 51 notice! The last loaded label from cf card is always again loaded after a restart of printer. Off: after a restart of printer the last used label must be again loaded manually from cf card. Notice! A common use of the functions autoload and hot...

  • Page 52

    Function menu compa ii series 52 operating manual 07.15 press key to arrive the next menu item. Off: in order to start the measurement procedure you have to change to the menu measure label. Measure: after switching on the printer, the loaded label is automatically measured. Feed: after switching on...

  • Page 53

    Compa ii series function menu 07.15 operating manual 53 6.8 interface switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the interface menu. Press key to select the menu. Com1: 0 - serial interface off. 1 - serial i...

  • Page 54

    Function menu compa ii series 54 operating manual 07.15 6.9 emulation switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the emulation menu. Press key to select the menu. Cvpl: carl valentin programming language zpl...

  • Page 55

    Compa ii series function menu 07.15 operating manual 55 6.10 date & time switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the date/time menu. Press key to select the menu. The upper line of display shows the curre...

  • Page 56

    Function menu compa ii series 56 operating manual 07.15 6.11 service functions notice! So that the distributor res. The printer manufacturer in case of service can offer fast support, the printer is equipped with the menu service functions. Necessary information such as selected parameters can be ta...

  • Page 57

    Compa ii series function menu 07.15 operating manual 57 press key to arrive the next menu item. Indication of printhead temperature. The printhead temperature corresponds normally to the room temperature. In case the maximum printhead temperature is exceeded, the current print order is interrupted a...

  • Page 58

    Function menu compa ii series 58 operating manual 07.15 press key to arrive the next menu item. Before the end of transfer ribbon, a signal is send by the control output. Setting of transfer ribbon advance warning diameter. In case you enter a value in mm then a signal appears via control output whe...

  • Page 59

    Compa ii series options 07.15 operating manual 59 7 options 7.1 cutter caution! Risk of injury, particularly during maintenance, the cutter blades are sharp! Switch off the before attaching the cutter! The cutter may only be used when it is mounted on the printer! Do not try to cut any materials whi...

  • Page 60

    Options compa ii series 60 operating manual 07.15 select the desired cutter operating mode, then press key to select additional functions. When using this function, after the first cut a feed with the set offset is effected and then cut anew. After the cut a back feed to the printing position is eff...

  • Page 61

    Compa ii series options 07.15 operating manual 61 7.2 dispenser i/o notice! In order to operate the printer in dispensing mode a print order has to be started and the printer has to be in 'waiting' mode. Switch on the label printer and the display shows the main menu. Press key to access the functio...

  • Page 62

    Options compa ii series 62 operating manual 07.15 after selection of desired dispenser i/o operating mode, press key to select additional parameters. Definition of port functions: 2 sign show the current setting for each port. Port 1 2 3 4 5 6 7 8 because of space reasons, the port number cannot be ...

  • Page 63

    Compa ii series options 07.15 operating manual 63 press key to arrive the next parameter. On: the start signal for the next label can already be released during printing the current label. The signal is registered from the printer. The printer starts printing the next label immediately after finishi...

  • Page 64

    Options compa ii series 64 operating manual 07.15 1 print start and cut (input) 2 error reset (input) 3 number of the file to load bit 0 (input) 4 number of the file to load bit 1 (input) 5 number of the file to load 2 (input) 6 number of the file to load 3 (input) 7 number of the file to load 4 (in...

  • Page 65

    Compa ii series options 07.15 operating manual 65 7.3 label applicator switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the label applicator menu. Press key to select the menu. Press key to change to the next mode...

  • Page 66

    Options compa ii series 66 operating manual 07.15 press key to arrive the next parameter. The vacuum is connected not immediately with print start, but only if the label were put forward a certain time. This delay causes that the label runs more easily under the pad as it is not sucked and in this w...

  • Page 67

    Compa ii series options 07.15 operating manual 67 press key to arrive the next parameter. This parameter is only active if the operating mode 'stamp on' is selected. The time period can be adjusted while the stamp is kept in the labelling position for applying the label onto the goods. Press key to ...

  • Page 68

    Options compa ii series 68 operating manual 07.15 press key to arrive the next parameter. Stroke adjust the arrester can be adjusted and the stroke speed can be set. The pad makes a stroke movement and return again to the basic position after reaching the lower end position. Press key to start the s...

  • Page 69

    Compa ii series options 07.15 operating manual 69 7.4 wlan switch on the label printer and the display shows the main menu. Press key to access the function menu. Press key as long as you arrive the wlan menu. Press key to select the menu. The menu item wlan can only be selected if a wlan card was r...

  • Page 71

    Compa ii series compact flash card / usb memory stick 07.15 operating manual 71 8 compact flash card / usb memory stick 8.1 general information on the back side of the label printer is the slot for the cf card and the usb port for inserting the usb memory stick. The mass storage menu (memory menu) p...

  • Page 72

    Compact flash card / usb memory stick compa ii series 72 operating manual 07.15 8.3 navigation the memory menu is operated with the keys of the foil keyboard of the control unit or with different function keys of an attached usb keyboard. Return to the previous menu. Function load layout: change to ...

  • Page 73

    Compa ii series compact flash card / usb memory stick 07.15 operating manual 73 8.4 define user directory notice! An user directory is to be defined: before using and/or navigating through the memory menu. If formatting of cf card is effected at pc and thus the standard directory was not created aut...

  • Page 74

    Compact flash card / usb memory stick compa ii series 74 operating manual 07.15 press key to access to the memory menu. Press key to call the file explorer. Press keys , , , to select the directory. Press key to display all available functions. Select the function set as user dir and press key to co...

  • Page 75

    Compa ii series compact flash card / usb memory stick 07.15 operating manual 75 8.6 file explorer the file explorer is the file manager of the printing system. The file explorer provides the main functions for the user interface of memory menu. In the user directory, press key to access to the file ...

  • Page 76

    Compact flash card / usb memory stick compa ii series 76 operating manual 07.15 loads a file. This can be a configuration saved before, a layout, etc. Press key to access to the memory menu. Press key to call the file explorer. Press keys and to select the file. Press key to load the selected file. ...

  • Page 77

    Compa ii series compact flash card / usb memory stick 07.15 operating manual 77 saves the complete, current printer configuration under the selected name. Press key to access to the memory menu. Press key to call the file explorer. Press key to change to the menu save file. Selct the function save c...

  • Page 78

    Compact flash card / usb memory stick compa ii series 78 operating manual 07.15 formats irrevocably the memory card. Notice! Usb sticks cannot be formatted at the printer! Press key to access to the memory menu. Press key to call the file explorer. Select the drive which is to format with the naviga...

  • Page 79

    Compa ii series compact flash card / usb memory stick 07.15 operating manual 79 creates a duplicate of the original file and/or the original directory to make changes independently of the original. Press key to access to the memory menu. Press key to call the file explorer. Press keys and to select ...

  • Page 80

    Compact flash card / usb memory stick compa ii series 80 operating manual 07.15 8.7 firmware update starting from firmware version 1.58 it is possible to make a firmware update also via the memory menu. Both the usb stick as well as the cf card can be used for this. On the cf card / usb memory stick...

  • Page 81

    Compa ii series maintenance and cleaning 07.15 operating manual 81 9 maintenance and cleaning danger! Risk of death by electric shock! Disconnect the label printer from power supply before performing any maintenance work. Notice! When cleaning the label printer, personal protective equipment such as...

  • Page 82

    Maintenance and cleaning compa ii series 82 operating manual 07.15 9.1 general cleaning caution! Abrasive cleaning agents can damage the label printer! Do not use abrasives or solvents to clean the outer surface of the label printer. Remove dust and paper fuzz in the printing area with a soft brush ...

  • Page 83

    Compa ii series maintenance and cleaning 07.15 operating manual 83 9.4 cleaning the label photocell caution! Label photocell can be damaged! Do not use sharp or hard objects or solvents to clean the label photocell. The label photocell can become dirtied with paper dust and this can adversely affect...

  • Page 84

    Maintenance and cleaning compa ii series 84 operating manual 07.15 figure 21 1. Turn lever (1) counter clockwise to lift up the printhead. 2. Remove labels and transfer ribbon from the label printer. 3. Remove hexagonal wrench (7) from its retainer and remove the rear cover of printer. 4. Slide the ...

  • Page 85

    Compa ii series maintenance and cleaning 07.15 operating manual 85 9.5 replacing the printhead notice! The printhead (7) is preinstalled on a head plate (1) and aligned at the factory. Figure 22 1 = head plate 2 = plug connection 3 = plug connection 4 = screw 5 = printing line 6 = pins 7 = printhead...

  • Page 86

    Maintenance and cleaning compa ii series 86 operating manual 07.15 figure 23 1. Turn lever (10) counter clockwise to lift up the printhead. 2. Remove labels and transfer ribbon from the label printer. 3. Remove hexagonal wrench (11) from its retainer. 4. Lightly keep printhead mounting bracket (9) o...

  • Page 87

    Compa ii series maintenance and cleaning 07.15 operating manual 87 9.6 replacing the print roller and rewind assist roller figure 24 1. Turn lever (1) counter clockwise to lift up the printhead. 2. Lift the pinch roller (5) off the rewind assist roller. 3. Remove labels and transfer ribbon from the ...

  • Page 88

    Maintenance and cleaning compa ii series 88 operating manual 07.15 figure 25 1. Pull print roller (7) and rewind assist roller (8) from the shafts (9, 10) on the housing. 2. Clean shafts (9, 10) of the rollers (see expanded view at shaft 10). 3. Slide print roller (7) and rewind assist roller (8) on...

  • Page 89

    Compa ii series error correction 07.15 operating manual 89 10 error correction error message cause remedy 1 line too high line rises up completely or partly over the upper edge of label. Move line down (increase y value). Check rotation and font. 2 line too low line rises up completely or partly ove...

  • Page 90

    Error correction compa ii series 90 operating manual 07.15 error message cause remedy 14 field numer received line number is invalid at rs-232 and centronics. Check sent data. Check connection pc - printer. 15 length mask invalid length of received mask statement. Check sent data. Check connection p...

  • Page 91

    Compa ii series error correction 07.15 operating manual 91 error message cause remedy 30 application identifier selected application identifier is not available in gs1-128. Check code data. 31 hibc definition f missing hibc system sign. Missing primary code. Check definition of hibc code. 32 system ...

  • Page 92

    Error correction compa ii series 92 operating manual 07.15 error message cause remedy 46 drive write- protected memory card is write-protected. Deactivate write protection. 47 directory not file attempt to indicate a directory as file name. Correct your entry. 48 file already open attempt to change ...

  • Page 93

    Compa ii series error correction 07.15 operating manual 93 error message cause remedy 64 zero point defective photocell. Change photocell. 65 compressed air pressure air is not connected. Check pressure air. 66 external releaser external print release signal is missing. Check input signal. 67 row to...

  • Page 94

    Error correction compa ii series 94 operating manual 07.15 error message cause remedy 82 time generation printing creation was still active at print start. Reduce print speed. Use printers' output signal for synchronisation. Use bitmap fonts to reduce generating time. 83 transport protection both dp...

  • Page 95

    Compa ii series error correction 07.15 operating manual 95 error message cause remedy 95 scanner layout difference scanner data does not correspond to bar code data. Check adjustment of scanner. Check scanner settings / connection. 96 com break serial interface error. Check settings for serial data ...

  • Page 96

    Error correction compa ii series 96 operating manual 07.15 error message cause remedy 110 housing open when starting the print order the housing cover is not closed. Close the housing cover and start the print order anew. 111 ean.Ucc code transferred ean.Ucc code is invalid. Verify bar code data (se...

  • Page 97

    Compa ii series error correction 07.15 operating manual 97 error message cause remedy 123 print asynchronous the label photocell do not work in the order as it is expected according to print data. Check label size and gap size. The settings of the photocell are not correct. Check label photocell set...

  • Page 99

    Compa ii series additional information 07.15 operating manual 99 11 additional information 11.1 column printing with this printer several columns can be printed, i.E. The information of one column can be printed several times (depending on its width) on a label. Caused by this the use of the complet...

  • Page 100

    Additional information compa ii series 100 operating manual 07.15 11.2 hotstart notice! Because of the fact that no battery-buffered sram is available, the necessary data has to be saved in another way, i.E. The data is saved onto cf card. Therefore the cf card is a condition for the hotstart menu i...

  • Page 101

    Compa ii series additional information 07.15 operating manual 101 in case at switching off the label printer a print order was active, then a print start is released automatically and the required res. Actual number of printed labels is refreshed. In case the print order was stopped at switching off...

  • Page 102

    Additional information compa ii series 102 operating manual 07.15 11.3 password the supervisor programs a cf card directly with the printer. He stores 10 different labels. As well he adjusts the printer parameters, like contrast, speed, etc. To the corresponding values. The user is only supposed to ...

  • Page 103

    Compa ii series additional information 07.15 operating manual 103 in case no password is defined res. The password protection is not activated, all functions can be used. In the function menu you will find the menu item 'password', where the password can be entered and the password protection activa...

  • Page 104

    Additional information compa ii series 104 operating manual 07.15 11.4 backfeed/delay in continuous dispensing mode (io dynamic continuous, io static continuous, io photocell continuous) no optimised backfeed is possible. Because of the fact when changing the print order, then the current label in t...

  • Page 105

    Compa ii series additional information 07.15 operating manual 105 dispenser: after printing the label it is driven into the dispensing offset and there waited. When releasing a new start signal (io dynamic) then the next label is immediately printed. Because of the fact that the label is already in ...

  • Page 106

    Additional information compa ii series 106 operating manual 07.15 11.5 photocells notice! When using reflection photocells you should observe that the label printer cover is closed and in this way other light (e.G. Working lamp) on the photocell is prevented. For this photocell type the transmitter ...

  • Page 107

    Compa ii series index 07.15 operating manual 107 12 index a assembly drawings ...................................................................... 6, 7, 8 b backfeed/delay ......................................................................... 104, 105 c column printing ............................

  • Page 108

    Index compa ii series 108 operating manual 07.15 i important notes .................................................................................... 5 initial operation ................................................................................... 27 inputs/outputs .............................

  • Page 109

    Compa ii series index 07.15 operating manual 109 t tear-off edge, removing/installing ...................................................... 39 transfer ribbon loading ................................................................ 37, 38 u usb stick change directory ..................................

  • Page 110

    Carl valentin gmbh neckarstraße 78 – 86 u. 94 . 78056 villingen-schwenningen phone +49 (0)7720 9712-0 . Fax +49 (0)7720 9712-9901 info@carl-valentin.De . Www.Carl-valentin.De.