© 2005 directed electronics, inc. Vista, ca n712t 01-05 m mooddeell 771122tt iinnssttaallllaattiioonn g guuiiddee note: this product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe...
Code hopping ® , doubleguard ® , esp ® , failsafe ® , ghost switch ® , learn routine™, nite-lite ® , nuisance prevention ® circuitry, npc ® , revenger ® , silent mode™, soft chirp ® , stinger®, valet ® , vehicle recovery system ® , vrs ® , and warn away ® are all trademarks or registered trademarks ...
3 © 2005 directed electronics, inc. Table of contents pprriim maarryy hhaarrnneessss ((h h11)),, 1122--ppiinn ccoonnnneeccttoorr .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..44 ppeerriipphheerraall pplluugg--iinn h ha...
© 2005 directed electronics, inc. 4 primary harness (h1), 12-pin connector ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ h1/1 red (+)12v constant power input before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the constant 12v ...
5 © 2005 directed electronics, inc. H1/3 black/white-1 domelight supervision input this wire determines what the output polarity of h1/4 will be. If the door pin circuit is negative, connect to chassis ground. If the door circuit is positive, connect to a fused 12v source. H1/4 black/white domelight...
© 2005 directed electronics, inc. 6 h1/11 black (-) chassis ground connection connect this wire to a clean, paint-free sheet metal location (driver kick panel) using a factory bolt that does not have any vehicle component grounds attached to it. A screw should only be used when in conjunction with a...
7 © 2005 directed electronics, inc. H1/15 yellow (+) switched ignition input connect this wire to an ignition source. This input must show (+)12v with the key in run position and during cranking. Make sure that this wire cannot be shorted to the chassis at any point. This wire will trigger the syste...
© 2005 directed electronics, inc. 8 peripheral plug-in harnesses super bright led, 2-pin white plug the super bright led operates at (+) 2 volt dc and plugs into the two-pin white port. Make sure the led wires are not shorted to ground as the led will be damaged. Multiple led’s can be used, but they...
9 © 2005 directed electronics, inc. Valet/program switch, 2-pin blue plug the valet/program button should be accessible from the driver’s seat. It plugs into the blue port on the side of the unit. Consider how the button will be used before choosing a mounting location. Check for rear clearance befo...
© 2005 directed electronics, inc. 10 4. Release. The valet ® /program switch can now be released. For example, to program the arming mode from active to passive, within 10 seconds of turning the ignition off, and press and release the valet/program switch once. Then press it again and hold it. The l...
11 © 2005 directed electronics, inc. System features menus n no ottee:: factory default settings are shown in b bo olld d. N no ottee:: for feature number 1-4, the 3.5 second door lock pulse setting the siren chirps twice, for the 0.4 second door lock pulse setting the siren chirps three times. Feat...
© 2005 directed electronics, inc. 12 setting is 0.8 second door lock pulses. For some vehicles a 0.4 second pulse duration is required, this durations is required for some vehicles to prevent the windows from moving. 5 double pulse unlock off/on: some vehicles require two pulses on a single wire to ...
13 © 2005 directed electronics, inc. 3. T trraannssm miitt.. While holding the valet/program button, press the button from the transmitter that you wish to assign to the selected channel. The unit will chirp indicating successful programming. It is not possible to teach a transmitter button to the s...
© 2005 directed electronics, inc. 14 transmitter configurations the transmitters can be programmed with the standard or single button arm/disarm configurations by using the auto learn functions in the transmitter/receiver learn routine. Standard configuration a remote that uses the standard configur...
15 © 2005 directed electronics, inc. Wiring quick reference guide led v alet switch green/bla ck loc k # 3 0 common o u tp u t white/blue (-) 200 ma ch a nnel 3 v a lididty o u tp u t bla c k/white o u tp u t of domelight s u per v i s ion rel a y # 8 7 lt . Green/bla c k f a ctor y al a rm d i sa r...
