Valor 550 Installation And Owner's Manual

Summary of 550

  • Page 1

    4001125-09 note: valor models 530 and 922 may be installed in an aftermarket permanently located manufactured (mobile) home, where not prohibited by local codes. Valor models 530 and 922 are only for use with the type of gas indicated on their rating plate. They are not convertible for use with othe...

  • Page 2

    2 casting tolerances due to the nature of cast iron, dimensional consistency may vary from one unit to the next and some variation in surface fi nish and fl atness is to be expected. We have done our best to control and make allowance for this; however some variation is inevitable. Insulation blanke...

  • Page 3: 530

    3 applications the valor model 530 heater with the 539 or 550 cast arch fronts comes ready for installation as a zero clearance unit into combustible type framing, without need for a separate zero clearance kit. The 530 installed without the standard zero clearance stand-off spacers may also be inst...

  • Page 4

    4 framing • the framing dimensions for installation of the 530 heater with the models 539 or 550 arch fronts are shown in the framing diagram. • a non-combustible hearth is not necessary in front of the 530 heater. • the 530 is approved for installation directly on any combustible material other tha...

  • Page 5

    5 installation 1. Fit top baffl e under the top panel of the appliance case. Secure with 2 thread forming screws. Fit the top air defl ector to the top baffl e as shown using the 2 screws provided. 2. Mount stand-off spacers. The stand-off spacers are supplied fl at and are left and right handed. A)...

  • Page 6

    6 6. Hang the inner cast arch. Insert the mounting hooks into the notches in the outer cast plate as shown. The fi t or gap between the inner cast arch and the outer cast plate may be tightened by bending the mounting hooks slightly inwards. Do not bend the hooks too far or the inner arch will be di...

  • Page 7

    7 cleaning to clean the barrier screen and the matte black cast iron surfaces use a soft brush. To clean the polished cast iron surfaces use mild soap and water. If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance. To clean the fi replace ...

  • Page 8: 922

    8 ceiling see mantel table a 36” min. To combust. Mat’l b min. 39-1/2” center line edge of protruding arch 4-3/4” clearances to combustible materials in front of opening 540wdk kit components a rch f ront i nstallation with 922 (539afb, 539afp, 549afb, 549afp) all arch fronts mounted to 922 fi rebox...

  • Page 9

    9 rest wire guard on fendre and clip top under canopy fasten outer arch to brackets using 2 screws per side inner arch hangs within outer arch on 2 hooks hearth fender rests on hearth installation 1. Install the mounting brackets and burner tray cover to the fi rebox as per instructions supplied wit...

  • Page 10

    10 # description 539 series 549 series 550 series black polished black polished 1 hearth fender 4000241ah 4000241 4000241ah 4000241 4001104 2 inner cast arch 4000240ah 4000240 4000240ah 4000240 4001094 3 hearth baffl e 4000347 4000347 4000347 4000347 4001100ah 4 outer cast arch 4000225ah 4000225 400...

  • Page 11

    11 # description part 1 wire guard 4000485 2 tray cover 4000486 3 canopy shield 4000312 4 adaptor mounting brackets (2) 4000352 5 top filler plate 4000487 r epairs p arts l ist (540wdk) designed and manufactured by / for miles industries ltd. 190 – 2255 dollarton highway, north vancouver, b.C., cana...