1. DL manuals
  2. Valor
  3. Indoor Fireplace
  4. DZ1GEC
  5. Installation Instructions And Owner's Manual

Valor DZ1GEC Installation Instructions And Owner's Manual

Summary of DZ1GEC

  • Page 1

    Electric fireplace dz1gec installation instructions and owner’s manual please read this manual before installing and operating this heater. This manual should remain with the homeowner. Easy to install and operate operates with or without heat no pollution, no smoke, no ashes csa certified plugs int...

  • Page 2

    2 congratulations! We know that there are a lot of other brands that you could have purchased, and we appreciate that you have chosen a valor product. Be assured that you have not only selected a superior heater, but also superior service. Your dedicated dealer will maintain the performance and effi...

  • Page 3: Table of Contents

    Table of contents safety information 4 specifications, dimensions & clearances 5 testing the unit 8 grounding 8 installation 8 installation with the bolero front 11 installation with the adorn front 13 installation with the arch fronts 15 operating instructions 17 maintenance 19 spare parts list 21 ...

  • Page 4: Safety Information

    4 safety information introduction this electric fireplace is designed for residential applications to be framed in as a zero clearance fireplace. This appliance has been tested in accordance with ul 2021 and csa c22.2 no. 46-m198 standards for fixed and location dedicated electric room heaters. Inst...

  • Page 5

    5 specifications, dimensions & clearances top view front view side view specifications power supply: 120 v; 15-amp grounded, circuit power cord length: 7’ (21. Cm) frequency: 60 hz heater btu output: 5000 btus heater power: 1500 w net weight: 4 lb / 15.4 kg note: a dedicated power supply circuit is ...

  • Page 6

    6 specifications, dimensions & clearances suggested apperture dimensions for custom backing plate (not supplied). Dimensions shown include the bracket kit 210efk. Trim for arches trim for bolero trim for adorn height: 25-1/2” (648 mm) width: 19-1/4” (489 mm) depth: 11” (279 mm) minimum for mantels a...

  • Page 7

    7 bolero front adorn front specifications, dimensions & clearances windsor arch w/no plate classic arch w/plate windsor arch w/plate.

  • Page 8: Grounding

    8 this section outlines how to install the fireplace insert into either: • an existing fireplace or; • a new construction or renovation. Existing fireplace installation thoroughly clean out the existing fireplace and hearth area. Seal all drafts, vents or ash clean outs with fiberglass insulation. S...

  • Page 9: Installation

    9 installation plan the power supply. If an existing grounded outlet is near the fireplace, the power cord can run along the front of the fireplace. If the cord is not long enough to reach the outlet, a grounded extension cord minimum awg no. 14 and rated to a minimum of 1875 watts, may be used. If ...

  • Page 10: Installation

    10 installation 210efk electric framing kit top panel (bolero, adorn, arches) rh extension bracket (bolero) lh extension bracket (bolero) rh side support (bolero, adorn, arches) rear mounting panel (bolero, adorn, arches) lh side support (bolero, adorn, arches) cross bar support (adorn) hooks for ca...

  • Page 11

    11 installation with the bolero front equipment required: 1 bolero front kit 541bpc 1 framing kit 210efk mount the side supports mount rear panel assemble extension brackets 1 2 3 bolero front bolero framing kit rear mounting panel ‘high set position approx. 75 mm (3”) 2 fixing screws from the engin...

  • Page 12

    12 change hooks on cast front 5 complete bracket assembly installation with the bolero front assemble top panel 4 assemble front to fireplace 6 rear view rear view rear view.

  • Page 13

    1 installation with the adorn front mount rear panel 1 mount the side supports 2 equipment required: 1 adorn front kit 92acf 1 framing kit 210efk adorn front side supports assembly adorn framing kit rh side ‘low’ set position approx. 30 mm (1-1/4”) 2 fixing screws from the engine back panel rear mou...

  • Page 14

    14 installation with the adorn front bend top panel’s tags upward 3 assemble top panel to fireplace 4 complete bracket assembly assemble front to fireplace 6 fix cross bar support to fireplace 5 rear view front view looking up from the floor.

  • Page 15

    15 installation with the arch fronts equipment required: 1 windsor arch kit 59afb or 59afp (w/plate) or 1 windsor arch kit 549afb or 59afp (w/out plate) or 1 classic arch kit 550cap (w/plate) 1 framing kit 210efk mount rear panel 1 mount the side supports 2 windsor arch windsor arch w/plate arch fra...

  • Page 16

    16 installation with the arch fronts assemble outer casting or backing plate to fireplace 5 complete bracket assembly assemble top panel to fireplace 4 bend top panel’s tags downward 3 hook inner casting to outer casting or backing plate 6 rear view rear view.

  • Page 17: Operating Instructions

    17 operating instructions the controls of the fireplace are located near the top of the unit behind a flip down panel / louver. Plug your electric fireplace. Flip down the front panel / louver near the top of the unit to reveal the controls. Main on/off power switch and led: the main on/off switch i...

  • Page 18: Operating Instructions

    18 operating instructions operating by remote control plug-in your electric fireplace. Make sure the unit’s main power on/off button is at the on position! The remote control will not work if the main power button is in the off position. When operating the remote control, it must be pointed towards ...

  • Page 19: Maintenance

    19 maintenance warning: the unit must be unplugged from the power supply prior to any maintenance or cleaning in order to reduce the risk electric shock or fire. Light bulb replacement procedure warning : the halogen light bulbs in your unit can become extremely hot. Allow at least 10 minutes betwee...

  • Page 20: Maintenance

    20 maintenance slide the spinner back on its metal bracket by inserting its plactic tab back in the bracket. Repeat steps 2 to 6 for the second bulb. Replace the coal ember bed by gently pushing it down. Replacing the flame generation bulbs (25 w maximum) on each side of the glass panel, there are 2...

  • Page 21: Spare Parts List

    21 spare parts list valor electric fireplace part number quantity description dz-rg 1 rear glass (mirror) dz-bp1006 1 back panel (control board, wires, and switches) dz-bh1006 1 blower and heating element assembly (cord and plug) bk25-10 10 bulb kit (25 w halogen) for drum flame bk5-10 10 bulb kit (...

  • Page 22: Spare Parts Diagram

    22 spare parts diagram dz-bp1006 06gt-21-002 r-15 dz-cm1006 bk35-10 bk25-10 dz1-lv1006 dz1-pb dz-bh1006 fm24 dz-cc dz-rc dz-cp dz-fb dz-lgr dz-rgr dz-tf dz-rg dz1-sw1006 dz1-bs (4).

  • Page 23: Wiring Diagram

    2 wiring diagram.

  • Page 24: Warranty

    24 warranty this electric fireplace was inspected, tested and carefully packaged to minimize the chance of dam - age during shipment. If a part (excluding light bulbs*) within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repa...