- DL manuals
- Value Hobby
- Toy
- 48in EPP MXS ARF
- Instrucition Manual
Value Hobby 48in EPP MXS ARF Instrucition Manual
Summary of 48in EPP MXS ARF
Page 1
48in epp mxs almost‐ready‐to‐fly instrucition manual specifications wingspan: 48 in (1230mm) length: 46in (1170mm) wing area: 471sq in (30.4sq dm) flying weight: 1.8-2.0lb (800-900g).
Page 2
Www.Valuehobby.Com/48in-mxs-epp.Html dear customer, congratulations on your purchase of 48in epp mxs arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that you can se...
Page 3
Www.Valuehobby.Com/48in-mxs-epp.Html safety in flying this is not a toy! It is a very high‐performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, away f...
Page 4
Www.Valuehobby.Com/48in-mxs-epp.Html recommended radio equipment product sku quantity radio flysky i6 6ch transmitter and receiver set fly-rc-4572 1 servo towerpro mg90s metal gear micro servo twp-sv-0358 4 servo extension universal (futaba/jr) servo extension 26awg 12in ams-ac-0560 2 y-harness univ...
Page 5
Www.Valuehobby.Com/48in-mxs-epp.Html main parts of airplane fuselage x 1 wing panel x 2 aileron x 2 horizontal stabilizer x 1 vertical stabilizer x 1 elevator x 1 rudder x 1 sfg x 2.
Page 6
Www.Valuehobby.Com/48in-mxs-epp.Html small parts and accessories: main landing gear x 1 plywood inserts x 1 wheel tail assembly x 1 plywood bracket x 1 450mm wing tube x 1 wing retainer hook x 2 rubber band x 4 long servo arm x 4 control horn x 4 1.8 x 150mm pushrod x 4 m2 x 6mm screws for servo arm...
Page 7
Www.Valuehobby.Com/48in-mxs-epp.Html section1. Aileron and aileron servo installation step1. Locate the wing panel, aileron and small trailing edge foam. Step2. Use the foam glue to glue the foam piece to the wing panel. Step3. Attach the aileron to the wing, and drip the ca to the hinges. Step4. Ap...
Page 8
Www.Valuehobby.Com/48in-mxs-epp.Html step6. Use two m2*6mm screws and two nuts to install the long servo arm to the stock servo arm. Install the pushrod connector to the long servo arm. Step7. Attach the pushrod to the control horn, and use glue to install the control horn into the plywood stiffener...
Page 9
Www.Valuehobby.Com/48in-mxs-epp.Html section2. Horizontal stabilizer and vertical stabilizer installation step1. Cut 10mm length foam piece from the rudder post step2. Insert the elevator into the fuselage. Step3. Insert the horizontal stabilizer to the fuselage. Step4. Insert the wing tube into the...
Page 10
Www.Valuehobby.Com/48in-mxs-epp.Html section3. Tail wheel and rudder installation step1. Assemble the tail wheel as shown and make a mark on the wire (20mm from the metal bracket). Step2. Bend the wire 90 degree as shown. Step3. Glue the tail wheel wire into the reinforcement tube in the rudder. Ste...
Page 11
Www.Valuehobby.Com/48in-mxs-epp.Html step7. Drill the mounting holes on the bracket. Step8. Secure the tail wheel to the bracket using the screws supplied in the tail wheel assembly bag. Section4. Elevator rudder installation step1. Attach the pushrod to the control horn, and use glue to install the...
Page 12
Www.Valuehobby.Com/48in-mxs-epp.Html step4. Use two m2*6mm screws and two nuts to install the long servo arm to the stock servo arm. Install the pushrod connector to the long servo arm. Step5. Install the servo arm to the servo, and slide the pushrod through the pushrod connector. Step6. Cut the exc...
Page 13
Www.Valuehobby.Com/48in-mxs-epp.Html step4. Use one m2*6mm screws and one to install the long servo arm to the stock servo arm. Install the pushrod connector to the long servo arm. Cut off the servo arm on the opposite side. Step5. Install the servo arm to the servo, and slide the pushrod through th...
Page 14
Www.Valuehobby.Com/48in-mxs-epp.Html section7. Wing installation step1. Glue the wing retainer hook to the wing root. Step2. Be sure the open end of the hook points the top side of the wing. Step3. Attach two wing panels to the fuselage through the wing tube. Step4. Use rubber band to connect the ho...
Page 15
Www.Valuehobby.Com/48in-mxs-epp.Html section8. Motor installation step1. Put the motor in position on the firewall and use a felt-tipped pen to mark the locations for mounting holes. Remove the motor and drill four mounting holes on the marked locations. Step2. Use four m3x12mm self-tapping screws t...
Page 16
Www.Valuehobby.Com/48in-mxs-epp.Html www.Valuehobby.Com 2015.07.27.