Ssssbach bach bach bach----342 epp 342 epp 342 epp 342 epp 3d profile 3d profile 3d profile 3d profile almost-ready-to-fly instruction manual wingspan: 863 mm (34.0 in) length: 915 mm (36.0 in) wing area: 19 sq dm (294.5 sq in) flying weight: 190-230 g (6.7-8.1oz).
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 2 dear customer, congratulations on your purchase of sbach-342 epp f3p from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and pro...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a saf...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 4 recommended radio equipment product sku quantity radio flysky t6 transmitter fly-rc-2563 1 servo towerpro sg90 9g micro servo twp-sv-0358 3 recommended power setup: product sku motor gforce 2204 1650kv outrunner brushless motor sat-mt-2493 esc...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 5.
Section 1: horizontal fuselage installation step1. Use foam safe ca to glue two pieces of horizontal fuselage together. Step2. Glue two carbon fiber strips (no.17: 538 x 3 x 0.5mm) to the fuselage using foam safe ca. Step3. Glue two carbon fiber strips (no.16: 142 x 3 x 0.5mm) to the nose of the hor...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 7 step4. Locate the items shown below and install them as shown. Section 3: carbon rod/landing gear installation step1. Slide the wheel to the landing gear wire and use the heat shrink tube to secure the wheel to the landing gear. Step2. As show...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 8 step3. Install the carbon rods to the fuselage and wings as shown..
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 9 section 4: aileron servo installation step1. Glue the aileron servo mount to the fuselage. Step2. Install the servo to the mount. (note: center the servo before mounting the servo arm)..
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 10 step3. Install two keeps to the two ends of the aileron pushrod (no.12 Φ1.5 x 169mm). Step4. Use the foam safe ca to install the control horn to the aileron. Center the aileron and use the pushrod to connect the servo arm and the control horn...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 11 step4. Insert the pushrod support into the fuselage as shown. Step5. Install a servo arm to servo. Center the elevator and connect the servo and control horn using assembled pushrod (no.13 Φ1.5 x 450mm). Step6. Repeat the previous steps for t...
Www.Valuehobby.Com/valuehobby-sbach342-epp-foamie.Html 12 section 6: motor installation step1. Locate the 3 items shown in the picture. Step2. Glue the motor mount to the nose of the fuselage as shown. Step3. Use four screws to install the motor to the mount. Step4. Install a 9 x 5 prop to the motor...
Www.Valuehobby.Com 2013-3-29.
