5mm epp 3d profile airplane arf instruction manual yak-54 sbach-342 specifications wing span: 34.0 in (863 mm) length: 36.0 in (915 mm) wing area: 294.5 sq in (19 sq dm) flying weight: 6.7-8.1oz (190-230 g).
Www.Valuehobby.Com/5mm-epp.Html 2 dear customer, congratulations on your purchase of 5mm epp arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that you can setup and ...
Www.Valuehobby.Com/5mm-epp.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, away from...
Www.Valuehobby.Com/5mm-epp.Html 4 recommended radio equipment product sku quantity radio flysky t6 6ch transmitter and receiver set fly-rc-2563 1 towerpro sg90 9g servo for aileron twp-sv-0357 1 servo towerpro sg50 5g servo for rudder and elevator twp-sv-0352 2 recommended power setup product sku mo...
Www.Valuehobby.Com/5mm-epp.Html 5 yak 54 main parts sbach342 main parts.
Www.Valuehobby.Com/5mm-epp.Html 6 accessories (same for two planes) 1. Landing gear x2 2. Wheel x 2 3. Heat shrink tube x 2 4. Control horn x 4 set 5. Pushrod connector x 4 6. Screw x 4 7. Steel wire with z-bend x 4 8. Motor mount 9. Hook and loop tape 10. Wood accessories 1 set.
Section1. Airframe assembly step1. Place the four parts of the horizontal fuselage in position on a flat work surface to make a=b. Use thin ca to glue them together. Insert and glue the no.15, no.16 and no.17 carbon fiber strips into the slots in the fuselage. Step2. Slide the vertical fuselage into...
Www.Valuehobby.Com/5mm-epp.Html 8 section3. Carbon rods installation glue no1. To no 11 carbon fiber rods to the fuselage and wing as shown. (the slots for cf rods were pre-cut in the factory.) section4. Tail skid installation glue one piece of no.15 carbon fiber strip to the fuselage as the tail sk...
Www.Valuehobby.Com/5mm-epp.Html 9 step3. Install the aileron servo arm. (center the servo electronically in advance.) step4. Install two 5g servos to the fuselage. (elevator and rudder servo) step5. Use the heat shrink tube to connect the no.12 carbon fiber rod and the steel wire with z bend as the ...
Www.Valuehobby.Com/5mm-epp.Html 10 step7. Glue the control horn mount to the aileron. Step8. Use a drill bit to enlarge the holes for the control horn. Step9. Apply some thin ca to the holes and install the control horn to the mount. Step10. Repeat the previous steps for the other aileron servo link...
Www.Valuehobby.Com/5mm-epp.Html 11 section6. Motor installation step1. Glue the epp foam motor mount to the plywood mount. Step2. Use the hot glue to secure the motor mount to the fuselage step3. Install the motor to the mount and install the prop. Center of gravity the recommended cg is 229mm (9in)...
Www.Valuehobby.Com/5mm-epp.Html 12 www.Valuehobby.Com 2013-08-20
