- DL manuals
- Value Hobby
- Toy
- Stylus Sport 60
- Instruction Manual
Value Hobby Stylus Sport 60 Instruction Manual
Summary of Stylus Sport 60
Page 1
Stylus sport 60 stylus sport 60 stylus sport 60 stylus sport 60 almost-ready-to-fly instruction manual specifications wingspan: 70.9 in (1800mm) length: 56.2in (1428mm) wing area: 795.1sq in (51.3sq dm) flying weight (gp): 7.28lbs (3300g) flying weight (ep): 6.72lbs (3050g).
Page 2
Www.Valuehobby.Com/stylus-sport-60.Html - 2 - dear customer, congratulations on your purchase of stylus sport 60 from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, and products that yo...
Page 3
Www.Valuehobby.Com/stylus-sport-60.Html - 3 - safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open are...
Page 4
Www.Valuehobby.Com/stylus-sport-60.Html - 4 - recommended setup main parts configuration model qty radio 4 channel 1 motor size gforce g46 brushless outrunner motor ′ 600kv) 1 speed control 80a brushless esc 1 recommended battery ′ lipo ″ gforce 40c 3300mah 4s 14.8v lipo 1 prop size 14 x 7 or 15 x 6...
Page 5
Www.Valuehobby.Com/stylus-sport-60.Html - 5 - accessories: pack1: engine mount-59x80mm (2.3x3.1in) 1 pair screw-m3*25mm (1.0in) 4pcs washer-Φ4mm (0.16in) 4pcs fuel tank assembly-360cc 1pcs cable tie-350mm (13.8in) 2pcs pack2: motor mount socket cap machine screw-m4*16mm (.6in) 4pcs nut m4 4pcs washe...
Page 6
Www.Valuehobby.Com/stylus-sport-60.Html - 6 - section 1: aileron installation required parts and hardware: wing panels ailerons hinges 8pcs step1. Locate the left aileron and four hinges. Slide the hinges into the precut hinge slots in the leading edge of the aileron. Saturate each of the hinges wit...
Page 7
Www.Valuehobby.Com/stylus-sport-60.Html - 7 - step3. Glue the two blocks onto the servo hatch. Step4. Use a 1.5mm (.06in) drill bit to drill two holes on the hatch as shown. The location for the holes should be in the central point of the blocks. Step5. Use two m2.5*8mm (.3in) self-tapping screws to...
Page 8
Www.Valuehobby.Com/stylus-sport-60.Html - 8 - step8. Use a 1.5mm (.06in) drill bit the drill the mounting hole as shown. Step9. Use four m2*8mm (.3in) self-tapping screws to install the servo hatch to the wing. Step10. Repeat the previous steps to finish the other aileron servo installation. Section...
Page 9
Www.Valuehobby.Com/stylus-sport-60.Html - 9 - step3. Use two m2*16mm (.6in) phillips round head screws and nut plate to install control horn on the aileron. Step4. Center the aileron. Use a felt-tipped pen to mark the pushrod where it crosses the arm servo. Step5. Bend the pushrod at the mark and cu...
Page 10
Www.Valuehobby.Com/stylus-sport-60.Html - 10 - step4. Use a brush to apply some epoxy to the exposed wood on the wing foot and the other half of the joiner. Step5. Slide two wing panels together, and use the low-tack tape to hold them tightly together until the epoxy fully cures. Step6. Use a drill ...
Page 11
Www.Valuehobby.Com/stylus-sport-60.Html - 11 - section 5: horizontal stabilizer & elevator installation required parts and hardware: horizontal stabilizer elevator joiner step1. Use the ruler and a felt-tipped pen to locate the center point in the trailing edge of the horizontal stabilizer. Step2. P...
Page 12
Www.Valuehobby.Com/stylus-sport-60.Html - 12 - step7. Use a 2.5mm (.1in) drill bit to drill the hole in the elevator as shown. Step8. Insert three hinges into the slot in the leading edge of the elevator. Step9. Apply some glue into the slot. Step10. Insert the end of the joiner into the elevator. S...
Page 13
Www.Valuehobby.Com/stylus-sport-60.Html - 13 - section 6: fin, rudder and tail wheel installation required parts and hardware: fin rudder triangle stock 2pcs fin mounting block tail wheel assembly step1. Locate the two triangle stock. Align one stock with the edge of the fin. Use a felt-tipped pen t...
Page 14
Www.Valuehobby.Com/stylus-sport-60.Html - 14 - step6. Use a knife to remove the coverings inside the lines drawn in the previous step. Step7. Use a brush to apply some epoxy on the bare wood of the horizontal stabilizer and the bottom of the fin as shown. Step8. Glue the fin onto the horizontal stab...
Page 15
Www.Valuehobby.Com/stylus-sport-60.Html - 15 - step11. Use a 2.5mm (.1in) drill bit to drill the hole and use a hobby knife to cut a groove as shown. Step12. Install the tail wheel assembly in the rudder. Apply some thin ca into the hinge slots and groove. Step13. Secure the tail wheel bracket to th...
Page 16
Www.Valuehobby.Com/stylus-sport-60.Html - 16 - step27. Center the elevator and servo arm. Attach the pushrod to the pushrod connector. Step28. Install the rudder control horn to the rudder. Step29.Center the rudder and rudder servo arm. Attach the pushrod to the servo arm through the connector as sh...
Page 17
Www.Valuehobby.Com/stylus-sport-60.Html - 17 - step4. Install the throttle servo on the servo tray. Electronically adjust the throttle arm and servo arm to make them move rightly. Secure the pushrod to the servo arm. Section 9: fuel tank installation required parts and hardware: fuel tank assembly s...
Page 18
Www.Valuehobby.Com/stylus-sport-60.Html - 18 - section 10: electric motor installation required parts and hardware: electric motor mount socket cap machine screw-m4*16mm (.6in) 4pcs nut m4 4pcs washer---Φ4mm (0.16in) 4pcs step1. Install the electric motor mount to the firewall with four m4*16mm (.6i...
Page 19
Www.Valuehobby.Com/stylus-sport-60.Html - 19 - step3. Use three m4*12mm (.5in) phillips roundhead screw and three Φ4mm (.16in) washers to secure the landing gear to the fuselage as shown. Section 11: canopy installation required parts and hardware: canopy self-tapping screw m2.5*8mm (.3in) 4pcs step...
Page 20
Www.Valuehobby.Com/stylus-sport-60.Html - 20 - www.Valuehobby.Com 2012-11-6.