Vantage Controls Axium 450 Series Instruction Manual - Precautions
3
Precautions
1. Recording Copyright
Unless it’s for personal use only, recording copyrighted
material is illegal without the permission of the copyright
holder.
2. Care
Occasionally you should dust the unit all over with a soft
cloth. For stubborn stains, use a soft cloth dampened
with a weak solution of mild detergent and water. Dry
the unit immediately afterwards with a clean cloth. Don’t
use abrasive cloths, thinners, alcohol, or other chemical
solvents, because they may damage the fi nish or remove
the panel lettering.
3. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME – READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to
country. Make sure that the voltage in your area meets
the voltage requirements printed on the unit’s rear panel
(e.g., AC 230V, 50HZ or AC 120V, 60Hz)
4. Power Cord
The power cord plug is used to disconnect this unit from
the AC power source. Make sure that the plug is readily
operable (easily accessible) at all times:
Never Touch This Unit With Wet Hands – Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside this
unit, have it checked by your Vantage / Axium dealer.
5. Handling Notes
•
If you need to transport this unit, use the original
packaging to pack it how it was when you brought it.
•
DO not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
•
This unit’s top and rear panels may get warm after
prolonged use. This is normal.
•
If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be sure
to use it occasionally.
6. Speaker Shorts
Under no circumstances should the speaker output
terminals of the unit be short circuited, or
connected to another output.
7. RS232 Connection
Avoid plugging the RS232 cable into the unit while
power is connected.
8. Direct Sun light
Avoid installing the amplifi er in positions
where the front panel is exposed to direct sunlight - may
cause control to become sluggish.
9. Controller Connection
Never connect more than four controllers to the
12VDC power supply terminals. The supply is internally
fused and will open circuit (self-resetting)
Never connect the amplifi er’s 12VDC terminals to
an external power supply.
For U.S. models
FCC information for User
CAUTION:
The user changes or modifi cations not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT FULLY INSERT.
Modèle pour les Candadien
REMARGUE: CET APPAPEIL NUMRIQUE DE LA CLASSE B
EST CONFORME À LA NORME NMB-003 DU CANADA.
Sur les modèles don’t la fi che est polarisée:
ATTENTION: POUR VITTER LES CHOCS LECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQ
AU FOND.