Vantage Hearth 850D-DA Instruction Manual - page 5

Preface and Safety Instructions 

850D-DA

iii

For U.S. models 

FCC information for User 

CAUTION: 

User changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to 

operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 

installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur 

in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined 

by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures: 

● 

Reorient or relocate the receiving antenna. 

● 

Increase the separation between the equipment and receiver. 

● 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

● 

Consult the dealer or an experienced radio/TV technician for help. 

For Canadian Models 

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. 

For models having a power cord with a polarized plug: 

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT. 

Modèle pour les Candadien 

REMARGUE: CET APPAPEIL NUMÈRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. 

Sur les modèles don’t la fiche est polarisée: 

ATTENTION:  POUR  ÈVITTER  LES  CHOCS  ÈLECTRIQUES,  INTRODUIRE  LA  LAME  LA  PLUS  LARGE  DE  LA  FICHE  DANS  LA  BORNE 

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQÚ AU FOND. 

Copyright Information 

Vantage Controls, Vantage, InFusion, Design Center, 850D-DA Digital Distributed Audio Amplifier, TPT TouchScreens and all other art 

work, brand and product names and designs are copyrighted, trademarks or registered trademarks of Vantage Controls Inc. All other 

art work, brand and product names and designs are copyrighted, trademarks or registered trademarks of their respective companies. 

Acknowledgments – FreeRTOS – uIP 

The 850D-DA firmware is based in part on FreeRTOS.org™ V5.0.2 and the uIP TCP/IP stack. For more information on FreeRTOS.org™ 

please visit http://www.freertos.org. Source code for FreeRTOS.org™ can be downloaded from their official website. The following 

copyright and statements for uIP TCP/IP stack, are required by license: 

Copyright (c) 2001-2003, Adam Dunkels. All rights reserved. 

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions 

are met: 

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the 

documentation and/or other materials provided with the distribution. 

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written 

permission. 

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS"' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 

NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 

STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 

TUV Certifications 

This product has been certified and conforms to UL60065 and certified to CAN/SSA, IEC 60065.