VAPamore MR-1000 FORZA Instruction Book And Users Manual - page 3
GETTING STARTED
Vapamore
if over pressure or over temperature is detected.
!
!
!
!
GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO
WHEEL INSTALLATION
Install the rear wheels using the supplied tools along
with the supplied wheel bolt, washers, and lock nut.
The wheel bolt is inserted into the wheel followed by a
washer then inserted into the steamer wheel mount.
Once inserted, install the other washer and the lock nut.
Tighten lock nut. (Fig.1)
Wheel bolt
Lock bolt
Once unpacked the only items that need to be installed are the rear wheels, the storage
basket, and the rear handles. All the necessary tools and hardware are included to
install these items.
Fig.1
BASKET & HANDLES
Fig.2
Bolt
Bolt
Cord
reel
Cord
reel
CORD REEL
The basket and handles are secured to the main steamer
body using 6 of the supplied Allen head style screws.
(*Note: there are extra Allen head screws provided).
Align the basket and handle screw hole locations and
insert the Allen head screws loosely until all screws are
in place. Once all screws are in place Secure all screws
firmly with the supplied Allen tool. (Fig.2)
The cord reel hooks rotate by pulling outward from the steamer then twisting to rotate.
Use this rotate function to easily remove the power cord and to position the hooks for
cord storage. Use the Velcro cord strap to secure the cord during transport. (Fig.2)
Washer
Forza
Always ensure the steamer is on a level floor or flat surface when in
!
At first start up and when refilling the cold water tank when empty you will
hear the pump fill the boiler from the cold water tank. Once the pump is running hold
the steam gun trigger down for 15-20 seconds to release the air trapped in the boiler.
!
operation. Do not tip or tilt the steam cleaner during use.
The accessory tool adaptor (#4 on parts overview
page) is required when using the jet nozzle
attachment, detail scraper, and all round detail
brushes (#5-12 on parts overview page). Align the
accessory with the arrow on the accessory tool
adapter and twist to lock into place. The accessory tool
adapter can be used directly on the steam gun or can
be used with the extension tubes. (Fig.2 and 3)
Accessory
storage
basket
The MR-1000 Forza has an accessory and
tool basket. Once all the accessories and tools have
been unpacked use the accessory storage bag and
basket to carry all the accessories and tools.
(Fig.1)
Accessories twist lock onto
the accessory tool adapter
Accessory tool adapter
attaches to the steam
gun or extension tubes.
(Fig.4)
ACCESSORIES AND TOOLS
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
!
GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO
Never operate machine without water in the main tank.
Water bottle
and holder
The MR-1000 Forza includes a water bottle holder
that can be used for the included water bottle or
most any other drink bottle or cup. The water bottle
holder fits over the front top rail on the accessory
and tool basket.
The large elbow adaptor (#14 on parts overview
page) is required when using the floor heads or
triangle corner brush (#15-17 on parts overview page)
With the large elbow adapter facing down, insert
into the floor heads or triangle brush until completely
inserted then rotate up. The adapter will only insert
when facing down and then locks into position and
allows the adapter to rotate when in use. The large
elbow adapter can be used directly on the steam
gun or can be used with the extension tubes.
Use large elbow adapter for
floor heads and triangle brush
The smooth surface squeegee, detail jet tool and the
bed bug / fabric tool (20-22 on parts overview page)
can be connected directly to the steam gun or the
extension tubes.
Use with steam gun
or extension tubes
STEAM GUN / EXTENSION TUBES
The steam gun connects to the steam socket located
on the front panel of the machine. Flip the dust cover
open and push the hose connector firmly into the
socket until both tabs click into place. Remove the
steam hose by pressing in both release tabs while
pulling out.
The steam gun has a trigger (ON) lock located just
behind the trigger. This lock can be used for
continuous steam without having to hold the trigger.
To set the lock, push down the trigger, then while the
trigger is down slide the lock to hold the trigger.
Extension tubes can be used for floors or difficult to
reach areas. The extension tubes push and lock into
place on the steam gun. (Fig.6)
Trigger lock
Extension tubes
lock and release