VAPamore MR-1000 FORZA Instruction Book And Users Manual - page 4
FILLING & OPERATION
Fig.1
!
er
Do not ov
!
The fill neck of the cold water tank has a screen in place to help prevent
Make sure the steam gun and hose is plugged into the
machine before startup. Plug the machine into a proper
wall outlet and switch on. At first start up you will hear
the pump fill the boiler from the cold water tank. Once
the pump is running hold the steam gun trigger down
for 15-20 seconds to release the air trapped in the boiler.
Once the boiler is full the pump will stop and the red
status light will light up showing the boiler is now
heating the water. Once the boiler is at operating
temperature the status light turns to green indicating
or
GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO
GENERAL FUNCTION: The MR-1000 Forza is a continuous flow steamer that uses a cold
water tank with a capacity of 4.2 ltr / .80 gal that fills the boiler tank as needed to create
steam. When first turned on, and during operation, the boiler will call for water from the
cold water tank to maintain steam pressure for continuous flow. Once the cold water
tank and boiler reach a low level the yellow “fill” light will light up and an audible beep
will sound to let the user know to refill the cold water tank. The boiler cut off is set to 6
bar (just over 90 psi). The steam pressure will fluctuate as the steamer is being used and
the boiler cycles on and off during use.
To fill the cold water tank, remove the rubber tank cap
located on the top of the machine and using the
supplied funnel, fill the tank (4.2 ltr / .80 gal). If filling
without measuring, fill to the mid-level of the fill neck
screen. (Fig.1)
Using additives of any kind will void the warranty.
!
Only fill with distilled water. Using “hard” mineral heavy water will clog
During use the steamer will continuously fill the boiler from the cold water tank. Once the
cold water tank and boiler reach a low level the yellow “fill” light will light up and an audible
beep will sound to let the user know to refill the cold water tank. Refill the cold water tank,
remove the rubber tank cap and fill to the mid level of the fill neck screen. (Fig.2)
(Fig.3)
Turn the controller knob clockwise to
increase the steam output and counter clockwise to
reduce the steam output.
.
internal components and can cause failure to internal parts and void the warranty.
debris from entering the steamers internal components. Never fill the cold water tank
without this screen in place. Failure to do so will void the warranty.
Fig.2
Fig.3
er
NOTE:
Do not ov
!
Cold water
tank fill cap
STATUS
PRESSURE
FILL
OUTPUT
ON
OFF
+
_
Water fill light
OUTPUT
+
_
Use steam controller
knob to adjust steam
output level
Status light
On / off
switch
the steamer is ready for use. (Initial start up from cold machine is aprox. 9 min) *The
status light will cycle red to green during use as the boiler maintains the temperature.
OPERATION
extension tube (use 1 to 2 tubes as desired). Ensure
Fig.1
Fig.2
Fig.3
The detail jet tool can be attached directly to the steam
gun or to any of the extension tubes. The jet nozzle
attachment is used with the accessory tool adapter.
These tools are great for removing soap scum in the bath,
shower, and faucets. Also for cleaning tight areas such as
toilet seat hinges where high pressure steam can reach
and blow out dirt and debris. These tools are most
effective when applied direct to the surface being
cleaned. The steam temperature will condense and cool
within 1’’ of the tool tip. (Fig.5)
Fig.5
DETAIL JET TOOL / JET NOZZLE
GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO
The floor head smooth surface is used with the micro
fiber pad for hard surface areas. Place the floor
cleaning head on the micro fiber pad and secure the
overhanging material under the clips located on each
side of the floor cleaning head. (Fig.2)
The floor head smooth surface is ideal for stone, tile,
vinyl and wood floors along with cleaning washable
walls and any hard surface. It can also be used to sanitize,
deoterize, kill allergens, bed bugs and dust mites. Attach
the micro fiber pad to allow the floor cleaning head to
glide when using on carpet. (Fig.3)
Carpets
‘
’
CLICK
Tools click into
extension tubes
Micro fiber pad
The floor head with bristles can be used on textured
floors, cement or tile along with any uneven surface
or where extra scrubbing strength is needed.
(with all bristle or brush tools, let the steam do the work
with just light pressure applied to the brush)
Use large elbow
adapter for triangle
brush
TRIANGLE CORNER BRUSH
The triangle corner brush can be used on upholstery,
carpets, and furniture along with textured floors, cement
or tile along with any uneven surface or where extra
scrubbing strength is needed. (Fig.4)
(with all bristle or brush tools, let the steam do the work
with just light pressure applied to the brush)
Fig.4
Detail jet tool
Jet nozzle on accessory tool adapter