- DL manuals
- Vari
- Lawn Mower
- BDR-595 D Adela
- Instructions For Use Manual
Vari BDR-595 D Adela Instructions For Use Manual
Summary of BDR-595 D Adela
Page 1
Drum mower bdr-595 adela instructions for use.
Page 2: Contents
Bdr-595 adela 2 contents 1 basic information. .............................................................................................................. 3 2 introduction. ....................................................................................................................... 4 2.1...
Page 3: 1 Basic Information.
Bdr-595 adela 3 1 basic information. ,ask your dealer to provide unpackaging of the machine and briefing. Fill in the following data concerning your machine. The data are important for ordering spare parts. It is advised to make a copy of this page with all data on the machine purchase for the case ...
Page 4: 2 Introduction.
Bdr-595 adela 4 2 introduction. Dear customer and user, thank you for the trust you have shown by purchasing our product. You have become owner of machine from a wide range of machines and attachments made by ,a.S. As a system of gardening, farming, small agricultural and communal technology. Drum m...
Page 5: 3 Operation Safety.
Bdr-595 adela 5 3 operation safety. 3.1 safety regulations. ,this international symbol indicates important messages concerning safety. When you see the symbol, be aware of a possible injury threatening to yourself or to other persons and read the attached instructions carefully. ,the machine operato...
Page 6
Bdr-595 adela 6 make sure there are no leakages and spills on engine parts when refuelling. If they happen to occur, dry out the stained parts or wait until the petrol evaporates. ,when the machine is in operation, all other persons (children in particular) and animals have to be outside the machine...
Page 7
Bdr-595 adela 7 l wa 2. 1..
Page 8: The Machine.
Bdr-595 adela 8 4 use, technical specification and technical description of the machine. 4.1 using the machine. Drum mower bdr-595 adela is designed and manufactured according to the latest knowledge in the field of the small gardening and farming machinery. It excels in easy maneouvrability, silent...
Page 9: 5 Instructions For Use
Bdr-595 adela 9 5 instructions for use 5.1 assembling the machine. Ask your dealer to provide unpackaging of the machine and briefing. Grip points for unpackaging the machine from the container: in front on the cutting disk, rear on the u tube of the machine frame. If you do the machine assembly you...
Page 10
Bdr-595 adela 10 6. Bolt the upper casing (6) to the metal holder on the lower casing (14) by means of bolt m5x10 (15) and a large flat washer Ø5.5 mm (16). Mudguards (17) are to be screwed to the upper casing (6) by using bolts m6x16 (18), nuts m6 (19) and large flat washers Ø 6.6mm (20). 7. Slide ...
Page 11
Bdr-595 adela 11 3. Let the new or cold engine running on choke for about 30 seconds (accelerator lever in the „choke“ position), then move the accelerator lever into the position „max“. In this position let the engine running for about 30 seconds. ,do not leave the machine alone when doing this. 5....
Page 12
Bdr-595 adela 12 note: all four main positions of the accelerator lever are arrested by means of a simple system of stamp/projection in the lever body. Clutch lever of the cutting disk drive and brake machine travel clutch lever accelerator lever (engine speed adjustment) bowden cable of the machine...
Page 13
Bdr-595 adela 13 5.5 stopping the machine. ,prior to carrying out any work in the near vicinity of the machine, switch off the engine and wait until the cutting disk stops! Always switch the engine off before leaving the machine. ,never let the engine running at maximum speed or idling with the cutt...
Page 14
Bdr-595 adela 14 rotations; this is why it is advised to switch it off by pushing the lever into the stop position as soon as possible!) 5.6 working with the machine. 5.6.1 working width of the machine. ,prior to the machine use, the sward must be cleared of solid bodies such as stones, wires, loose...
Page 15
Bdr-595 adela 15 5.6.3 problems at cutting. Choking of the cutting disk cover space with the cut material manifests as follows: a) engine markedly losing speed but not stalling: machine travel to be switched off immediately (lever on the left handrail grip); drive on reverse gear just a bit with a s...
Page 16
Bdr-595 adela 16 6.1 machine lubrication. 6.1.1 gear oil replacement and refilling. ,when replacing oils, follow the basic hygienic principles, regulations and laws on environment protection. The gearing works in an oil bath. Oil volume should be checked once a month (oil plugs see fig. 4). Minimum ...
Page 17
Bdr-595 adela 17 6.1.2 engine oil replacement. See the operating manual for engine. To drain oil, the machine should be either tilted to the side with the pour-in neck with oil gauge, or the engine should be dismounted from the machine (see chapter 6.4, items a),b),d) ). 6.1.3 table of machine lubri...
Page 18
Bdr-595 adela 18 6.2 tightening the bolted connections. Check the bolted connections for their proper tightening. Prior to each machine use, check the tightening of bolts fastening the blades in the upper disk as well as the tightening of bolts fastening the lower disk onto the flange. 6.3 replaceme...
Page 19
Bdr-595 adela 19 ,the engine must be switched off and the cable end connector to the spark plug disconnected! 1. Hold the upper disk so that it does not turn and dismount the blade bolted connection by using barrel spanner no. 16 and flat wrench no. 17. 2. Take the blade and parts of the blade seati...
Page 20
Bdr-595 adela 20 6.4 v-belt replacement and adjustment of tightening pulley. V-belt should be replaced according to its wear (cracked sides, torn belt, sides worn out down to belt carrier fibres, belt “pulled“ out of shape) or after about 100 hours of operation at the maximum. In this machine, the b...
Page 21
Bdr-595 adela 21 approx. 1.5 – 2.0 cm from the bottom of the tightening pulley (see fig. 7) and the cable in the bowden of the tension pulley must exhibit no slackness. In the case that the adjustment bolt is completely screwed out and it is necessary to tighten the v-belt, the spring on the cable c...
Page 22
Bdr-595 adela 22 6.5 adjusting the litz wires of pulley, brake and machine travel gear clutch. In order to guarantee low operating forces on levers which control the drive switching, it is advisable to lubricate the cables in bowdens at least 2x during the season with some of oils available in atomi...
Page 23
Bdr-595 adela 23 6.6 diagnostics of driving problems. Wheel travel gear clutch does not switch- off improperly adjusted steering litz wire no rumbling must be heard from the gearbox when manually turning the travel wheel in counter-travel direction (wheel gear switched off). Keep screwing in the adj...
Page 24
Bdr-595 adela 24 6.7 table of service operations. Operation during season after season gearbox oil volume check 1x monthly yes,* engine oil volume check prior to each machine use ** engine air filter check prior to each machine use check check of blades for fastening and intectness prior to each mac...
Page 25
Bdr-595 adela 25 c) clean the wheel hub inside, wheel hub flange with balls and the free wheel from dirt and old grease. D) fill the hub inside with new grease (e.G. For water pumps) lubricating at the same time also the flange with balls and free wheel surfaces. E) slide the free wheel on the wheel...
Page 26
Bdr-595 adela 26 6.10 disposal of packaging and machine after the end of service life. After unpacking the machine, you are obliged to provide for the disposal of packaging material with taking into account the use of secondary raw-materials according to waste law no. 185/2001 gaz. (and its amendmen...
Page 27: 9 List Of Components.
Bdr-595 adela 27 9 list of components..
Page 28
Bdr-595 adela 28 9.1 machine casing.
Page 29: Machine Casing
Bdr-595 adela 29 machine casing pos. Part name dimensions drawing-standard ord. No. Pcs 1 frame 22 9 1536 050 196 001 1 2 screen holder 22 9 1856 005 169 016 1 3 4 handle 22 9 8044 009 196 016 1 5 upper cover 22 9 8545 028 196 015 1 6 mudflap holder 32 0 1530 129 196 012 1 7 8 mudflap 32 0 8530 036 ...
Page 30
Bdr-595 adela 30 9.2 handlebars.
Page 31: Handlebars
Bdr-595 adela 31 handlebars pos. Part name dimensions drawing-standard ord. No. Pcs 1 handlebars weldment 22 9 8078 059 196 002 1 2 control lever 32 0 8058 009 196 013 2 3 4 clutch bowden cable 622 9 8074 044 196 515 1 5 pulley bowden cable 622 9 8074 045 196 516 1 6 brake bowden cable 622 9 8074 04...
Page 32
Bdr-595 adela 32 9.3 cutting disc drive.
Page 33: Cutting Disc Drive
Bdr-595 adela 33 cutting disc drive pos. Part name dimensions drawing-standard ord. No. Pcs 1 brake shoe 22 9 1664 024 189 014 2 2 driven pulley 22 9 3325 012 189 004 1 3 upper disc 22 9 5025 011 196 056 1 4 brake cam 22 9 8032 048 196 003 1 5 pulley arm 32 0 3330 034 196 010 1 6 driving disc holder...
Page 34
Bdr-595 adela 34 9.4 wheel drive.
Page 35: Wheel Drive
Bdr-595 adela 35 wheel drive pos. Part name dimensions drawing-standard ord. No. Pcs 1 gearbox bdr-595 22 9 3282 052 196 014 1 2 driving pulley 22 9 3325 032 196 046 1 3 driven clutch element 32 0 3625 029b 196 045 1 4 engine plate 22 9 8032 049 196 007 1 5 feather 3/16" 32 0 3330 021 189 036 1 6 bo...
Page 36
Bdr-595 adela 36 9.5 gearbox.
Page 37: Gearbox
Bdr-595 adela 37 gearbox pos. Part name dimensions drawing-standard ord. No. Pcs 1 fork weldment 22 1 3330 013a 189 078 1 2 complete lever 22 9 3330 017 196 022 1 3 complete driving disc 22 9 3616 006 189 029 1 4 worm 2:54 32 0 3214 028 196 023 1 5 worm wheel 32 0 3221 016 196 027 1 6 shaft - wheel ...
Page 38: 10 Letter Of Guarantee
Bdr-595 adela 38 10 letter of guarantee to be completed by manufacturer name of product drum mower model bdr-595 adela serial number …………………………………………………………………………. Engine serial number …………………………………………………………………………. Warranty (months) …………………………………………………..……………………... Output control …………………………………………………....
Page 39
Bdr-595 adela 39 warranty inspection 1 date: ………………………………………person in charge:………………………………………………… service shop stamp and signature warranty inspection 1 machine model………………………… serial no.:…………………………… warranty inspection 2 date:………………………………………person in charge:………………………………………………… service shop stamp and...