Summary of TRIMMER-50
Page 1
String mower trimmer 50 trimmer 60 instructions for use.
Page 2
Trimmer-50 trimmer-60 2 contents 1. Basic information 2. Introduction 2.1 warning 3. Operation safety 3.1 safety regulations 3.2 safety pictographs 3.3 maximum values of noise and vibrations 4. Use, technical specification and technical description of the machine 4.1 use of the machine 4.2 technical...
Page 3
Trimmer-50 trimmer-60 3 1. Basic information ! Ask your dealer to provide unpackaging of the machine and briefing. Fill in the following table with data on your machine. The data are important for ordering spare parts. It is advisable to have a copy of this page with all data on the machine purchase...
Page 4
Trimmer-50 trimmer-60 4 2. Introduction dear customer, thank you for trust that you have shown by purchasing our product. You have become owner of one machine from a wide range of machines and attachments made by vari, a.S. As a system of gardening, farming, small agricultural and communal technolog...
Page 5
Trimmer-50 trimmer-60 5 3 operation safety 3.1 safety regulations ! This international symbol indicates important messages concerning safety. When you see the symbol, be aware of a possible injury to yourself or to other persons and read attached instructions carefully. ! The machine operator must b...
Page 6
Trimmer-50 trimmer-60 6 ! Protect your eyes and face by using approved working aids! Regarding the fact that the permitted noise levels are to be exceeded (see table of expositions at the end of the chapter), it is necessary to use ear protectors to csn en 352-1. To protect eyes and face use means o...
Page 7
Trimmer-50 trimmer-60 7 string head assembly options 1 2 location : right side of the machine frame 1- putting one´s hands or feet into the working tool space is prohibited-danger of limb injury. 2- keep a safe distance from the machine –danger of injury by flying material fragments. Self-sticker fo...
Page 8
Trimmer-50 trimmer-60 8 3.3 maximum values of noise and vibrations. Maximum values of noise and vibrations as measured by ao-206 szzpls praha test report no. 15 141 of 12 october 1999 no. 15 145 of 27 october 1999 no. 15 142 of 13 october 1999 no. 15 146 of 2 november 1999 product trimmer 50 trimmer...
Page 9
Trimmer-50 trimmer-60 9 4.2 technical specifications technical specification of the machine trimmer 50 trimmer 60 length mm 1251 mm 1251 width mm 572 mm 612 height mm 1032 mm 1032 weight kg 35 kg 36.5 max. Engagement width cm 50 cm 58 working tool rotations min -1 4337 min -1 3855 max. Circumferenti...
Page 10
Trimmer-50 trimmer-60 10 4.3 technical description of the machine the base of the machine is a rigid frame on which a combustion engine is placed. The machine is equipped with covers against flying cut material. A screen of plastic canvas placed between the wheels prevents flying chips. Tubular hand...
Page 11
Trimmer-50 trimmer-60 11 figure 1 5. Instructions for use 5.1 machine assembly ask your dealer to provide unpackaging of the machine and briefing. Grip points: a) front: - front edge of the lower casing; b) rear: - handlebar grips or machine frame cross-bar when the handlebars are folded. If you ass...
Page 12
Trimmer-50 trimmer-60 12 5.2 putting into operation read the instruction for engine use thoroughly! You can prevent a possible damage to the engine. 1. Fill the engine with the prescribed types and volumes of oil and petrol. 2. Instructions for making the motor ready for starting and instructions fo...
Page 13
Trimmer-50 trimmer-60 13 note: in a new or cold engine, engine stalling may occur at the several first string head drive starts. The phenomenon disappears after the engine has warmed up. 5.4 machine travel the machine is not equipped with the travel and it must be therefore pushed into the engagemen...
Page 14
Trimmer-50 trimmer-60 14 adjust the engine speed at maximum, let the string head run on maximum rotations and then drive the machine against the stand to be cut. The mown stand will be thrown onto the right side of the machine (as viewed by the operator). Should the stand be low and not too dense or...
Page 15
Trimmer-50 trimmer-60 15 ! Always replace both the strings. Poor balance of the string head may result in a machine damage. Caution! When mowing in the stand with a lot of solid objects, near walls, fences or curb stones, a string breakage occurs more frequently, resulting in the reduction of machin...
Page 16
Trimmer-50 trimmer-60 16 5.6.4 tilting of the machine machine tilting to sides (out of machine axis) is used for final trimming near curb stones, fences or walls (edges in general), i.E. At places impossible to reach with a common grass mower. Tilting is to be made as follows: 1. Press the axle arre...
Page 17
Trimmer-50 trimmer-60 17 5.7 advised accessories a guide wheel (order.No. 3878) is advised to improve the leading of the string head above the terrain. A set of disk holder (order.No. 3881) is recommended for greater applicability of the machine to join the mowing disks or saw blades. The specificat...
Page 18
Trimmer-50 trimmer-60 18 5.7.2.2 working with the saw blade the saw blade is meant for undercutting the self-seeded trees and shrubs up to a (znaČka!) of max. 5 cm. • set-up maximum speed and switch on the working tool drive see chapter starting the mowing tool. • drive the saw blade slowly into the...
Page 19
Trimmer-50 trimmer-60 19 6. Maintenance, care and storage to ensure a long-term satisfaction with our product, it must be given proper care and maintenance. Regular maintenance of the machine will prevent its early wear ensuring at the same time a correct functioning of all its parts. Follow all ins...
Page 20
Trimmer-50 trimmer-60 20 6.1.2 lubrication and assembly of wheels • underlay the machine so that the wheels can freely turn. The machine must be secured against spontaneous movement. • dismount the nut and the outer cone by using the spanner no. 15. Remove the wheel from the axis. • press the bearin...
Page 21
Trimmer-50 trimmer-60 21 the replacement procedure is as follows: a) drainpetrol from the engine tank. Dismount the accelerator lever (2x spanner no. 8) from the handlebars. Bowden cable should never be dismounted from the control on the engine! B) unscrew three safety nuts (spanner no. 13) on the e...
Page 22
Trimmer-50 trimmer-60 22 figure 14 figure 15 6.4 table of service operations operation during the season after the season engine oil check prior to each use ** engine air filter check prior to each use check string holder check prior to each use *** check check of intactness of upper and lower disk ...
Page 23
Trimmer-50 trimmer-60 23 ** oil replacement intervals see operating manual for engine; *** in the case of damage (even at cutting) – cracks, bending, breakage etc. – repair required immediately! **** or replacement after about 100 hours. 6.5 washing and cleaning of the machine ! At cleaning and wash...
Page 24
Trimmer-50 trimmer-60 24 7 instructions for ordering spare parts the following data are to be used for easier identification when ordering the spare parts: 1. Machine type, engine type, machine serial number and year of manufacture; 2. Ordering number given by manufacturer and its name in the compon...