Varytec Strobe Mini LED20 Manual - page 5
Prevent that the power cable has contact
power connections. Don’t touch them with clammy hands.
Make sure that the voltage which is to connect not exceeds the specified values.
Make sure that it isn’t possible to squeeze or damage the
yourself with regular checks that there are no damages to the power cable or the device.
Don’t switch the device in short time intervals (e.g. in second cycle) on or off.
Keep away children and laymen off the device
Health risk!
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined by a doctor.
install it in danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences
Designated use
This device was developed for professional use on stages, in discos, theatres etc. The
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increase the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that no cables are lying around. You would endanger your own safety and also the safety of
a third party.
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device
and could cause deathly electric shocks. If you use fog devices
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
The ambient temperature has to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.
5 / 12
Prevent that the power cable has contact with other cables. Handle carefully with power cables and
power connections. Don’t touch them with clammy hands.
Make sure that the voltage which is to connect not exceeds the specified values.
Make sure that it isn’t possible to squeeze or damage the power cable with sharp edges. Assure
yourself with regular checks that there are no damages to the power cable or the device.
Don’t switch the device in short time intervals (e.g. in second cycle) on or off.
Keep away children and laymen off the device.
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
individuals whose epilepsy was determined by a doctor. Therefore do not
danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences
This device was developed for professional use on stages, in discos, theatres etc. The
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increase the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that no cables are lying around. You would endanger your own safety and also the safety of
d to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device
and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
as to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.
with other cables. Handle carefully with power cables and
power cable with sharp edges. Assure
yourself with regular checks that there are no damages to the power cable or the device.
Don’t look directly into the light source. At certain circumstances it is
possible that some people get epileptic seizures. This is especially true for
Therefore do not
danger zones (such as stairs, exit routes ...). Point out the visitors
before operating on the use of a strobe. Avoid prolonged flash sequences.
This device was developed for professional use on stages, in discos, theatres etc. The device is only
approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Avoid convulsions or any form of forceful impact during the installation or the start-up of the device.
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that no cables are lying around. You would endanger your own safety and also the safety of
d to operate or store the device in an environment in which spray water, rain, humidity
or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device
the device has not be exposed to a
direct smoke jet. There has to be a safety distance of at least 0.5m between this device and the fog
machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
as to be between 0°C and +40°C. Avoid direct sunlight and close proximity
to heaters. You have also to attend it during the transport in closed motor vehicles.