- DL manuals
- Vector2
- Gate Opener
- V400
- Installation Instructions Manual
Vector2 V400 Installation Instructions Manual - Operator V400/v500
Power Configurations:
Extention/retraction
(no load):
Max. Output Force:
Max. Operations (day):
Standby Operations:
Standby period:
½ day
1 day
2 days
Typical Gate Opening/
Closing Time:
Operating Temp. Range:
Housing Protection:
Mass of Operator:
Operator Stroke:
DC Current Draw (Max):
Nominal Input Voltage:
12V DC
15A
27mm/sec
250kgf
V400: 5.5kg
V500: 5.9kg
V400: 400mm
V500: 500mm
V400: <14 Sec
V500: <17.5 Sec
-20°C to +60°C
IP55
Battery 40AH <200 cycles
Battery 40AH <200 cycles
Battery 7AH <115 cycles
Battery 7AH <85 cycles
Battery 7AH <7 cycles
NA
Battery 40AH <200 cycles
Battery 40AH <200 cycles
Battery 40AH <200 cycles
100*
12V DC
15A
27mm/sec
250kgf
200
V400: <14 Sec
V500: <17.5 Sec
V400: 5.5kg
V500: 5.9kg
V400: 400mm
V500: 500mm
-20°C to +60°C
IP55
7AH, 12V, CP84E
(Domestic)
7AH, 12V, CP84SM2A
(Light Industrial)
Standby period:
½ day
1 day
2 days
Double kit inc controller only
Battery 7AH <140 cycles
Battery 40AH <200 cycles
Battery 7AH <75 cycles
Double kit inc controller and 2 sets safety beams
Operator V400/V500
*
Limited by the charging rate
Higher capacity battery can also be used must be housed separately e.g. 40AH.
Page 6
Overall Dimensions
1400mm Extended
1400mm Extended
1000mm Retracted
1000mm Retracted
400mm Stroke
400mm Stroke
Model V400
100
95mm
All dimensions shown in millimetres
Model V500
1600mm Extended
1600mm Extended
1100mm Retracted
1100mm Retracted
100
95mm
All dimensions shown in millimetres
500mm Stroke
500mm Stroke
Figure 1 Overall Dimensions
Specifications
Specifications
Page 7
15A (fused)
18V DC
48mA
2A DC
3A (PTC)
Current Sense & Redundant Optical
Redundant Optical
-20°C to +60°C
Max. Motor Current Per Channel:
Max. Input Voltage:
Standby Current Draw:
Max. Solenoid Current Draw:
Max. Aux Output Current:
Collision Detection:
Position & Trajectory:
Temperature Range:
Control Card
Limited by maximum daily usage
Limited by maximum daily usage
Summary of V400
Page 1
Otech group pty t: 07 3205 1123 f: 07 3205 1124 e: info@rotech.Com.Au.
Page 2
Centurion systems has been manufacturing automatic gate systems since 1987, and is committed to providing reliable, cost effective solutions in the field of access automation. Centurion strives to give service and backup second to none. Our engineers are available to give sales support, installation...
Page 3: Warnings For The Installer
Important safety instructions important safety instructions page 4 to ensure the safety of people, it is important that you read all the following instructions. Incorrect installation or incorrect use of the product could cause serious harm to people. The installer, being either professional or diy,...
Page 4: Warnings For The Installer
Important safety instructions important safety instructions page 4 to ensure the safety of people, it is important that you read all the following instructions. Incorrect installation or incorrect use of the product could cause serious harm to people. The installer, being either professional or diy,...
Page 5: Operator V400/v500
Power configurations: extention/retraction (no load): max. Output force: max. Operations (day): standby operations: standby period: ½ day 1 day 2 days typical gate opening/ closing time: operating temp. Range: housing protection: mass of operator: operator stroke: dc current draw (max): nominal inpu...
Page 6: Operator V400/v500
Power configurations: extention/retraction (no load): max. Output force: max. Operations (day): standby operations: standby period: ½ day 1 day 2 days typical gate opening/ closing time: operating temp. Range: housing protection: mass of operator: operator stroke: dc current draw (max): nominal inpu...
Page 7: Allowable Gate Mass
Page 8 allowable gate mass maximum allowable gate mass for v400 operator: gate swing angle up to up to up to up to up to up to 1.5m 2m 2.5m 3m(#1) 3.5m(#1) 4m(#1) 90° 500kg 500kg 500kg 360kg 260kg 200kg 100° 500kg 500kg 388kg 160kg 190kg 150kg 110° 500kg 306kg 198kg 130kg 120° 180kg 100kg 65kg (#1 -...
Page 8: Allowable Gate Mass
Page 8 allowable gate mass maximum allowable gate mass for v400 operator: gate swing angle up to up to up to up to up to up to 1.5m 2m 2.5m 3m(#1) 3.5m(#1) 4m(#1) 90° 500kg 500kg 500kg 360kg 260kg 200kg 100° 500kg 500kg 388kg 160kg 190kg 150kg 110° 500kg 306kg 198kg 130kg 120° 180kg 100kg 65kg (#1 -...
Page 9
Page 10 item description qty. Part no. 1 wall bracket (high security) 1 1050m30000 2 padlock 2 m-pltri263 4 vector high security kit packing leaflet 1 doc1050d05 high security kit (optional) vechsk00v1 page 11 control box including charger & controller (domestic) veccad00v2 / (light industrial) vecc...
Page 10
Page 10 item description qty. Part no. 1 wall bracket (high security) 1 1050m30000 2 padlock 2 m-pltri263 4 vector high security kit packing leaflet 1 doc1050d05 high security kit (optional) vechsk00v1 page 11 control box including charger & controller (domestic) veccad00v2 / (light industrial) vecc...
Page 11
Page 12 required tools & equipment required tools & equipment figure 4 required tools and equipment spanner 17mm, 15mm preferably socket set screw drivers 6mm philips 3.5 flat crimping tool and pin lugs pliers side cutters hammer 2 x g-clamps electric drilling machine measuring tape hacksaw angle gr...
Page 12
Page 12 required tools & equipment required tools & equipment figure 4 required tools and equipment spanner 17mm, 15mm preferably socket set screw drivers 6mm philips 3.5 flat crimping tool and pin lugs pliers side cutters hammer 2 x g-clamps electric drilling machine measuring tape hacksaw angle gr...
Page 13: Strength Of The Pillar
Page 15 site considerations site considerations page 14 in order to ensure a reliable and durable installation thought should be given to: strength of the pillar for reliable operation it is important to ensure that the way the operator is secured to the wall takes into account the strength of the p...
Page 14: Strength Of The Pillar
Page 15 site considerations site considerations page 14 in order to ensure a reliable and durable installation thought should be given to: strength of the pillar for reliable operation it is important to ensure that the way the operator is secured to the wall takes into account the strength of the p...
Page 15
Cabling requirements cabling requirements figure 6 cabling requirements figure 5 minimum installation requirements page 17 1. 220v ac mains cable via mains isolator or switch (3 core lne 0,5mm²)* 2 optional keypad ( 3 core 0,5mm multi- or stranded). Low voltage 16v ac battery charger 6. Optional inf...
Page 16
Cabling requirements cabling requirements figure 6 cabling requirements figure 5 minimum installation requirements page 17 1. 220v ac mains cable via mains isolator or switch (3 core lne 0,5mm²)* 2 optional keypad ( 3 core 0,5mm multi- or stranded). Low voltage 16v ac battery charger 6. Optional inf...
Page 17
4. Secure the bracket to the wall with the most appropriate means. It is critical that the wall bracket is securely mounted. See page 14 for site considerations. 5. Fit the gate bracket to the operator. 1 or 2 turns 6. Fit the motor end of the operator to the wall bracket. 7. Open the gate fully and...
Page 18
4. Secure the bracket to the wall with the most appropriate means. It is critical that the wall bracket is securely mounted. See page 14 for site considerations. 5. Fit the gate bracket to the operator. 1 or 2 turns 6. Fit the motor end of the operator to the wall bracket. 7. Open the gate fully and...
Page 19: Adjust Origin Clamp
Or 13.Unlock the operator and open the gate fully. 14. Slide the origin clamp along the actuator tube, right up to the operator. Secure in place with an allen key tighten properly. 15. Attach warning decals to the gate as shown. 2 1 adjust origin clamp (nb - not required for outward swinging gates) ...
Page 20: Adjust Origin Clamp
Or 13.Unlock the operator and open the gate fully. 14. Slide the origin clamp along the actuator tube, right up to the operator. Secure in place with an allen key tighten properly. 15. Attach warning decals to the gate as shown. 2 1 adjust origin clamp (nb - not required for outward swinging gates) ...
Page 21: For V400 (400Mm Operator)
Alternative positions a and b ‘min value’ gate swing a+b should up to up to up to up to up to up to angle not exceed 1.5m 2m 2.5m 3m 3.5m 4m 60° - 90° or less 460mm 100° 400mm 110° 340mm 120° 285mm recommended positions (only for a 2.5m gate or shorter) a value b value 90° or less 205 250 100° 165 2...
Page 22: For V400 (400Mm Operator)
Alternative positions a and b ‘min value’ gate swing a+b should up to up to up to up to up to up to angle not exceed 1.5m 2m 2.5m 3m 3.5m 4m 60° - 90° or less 460mm 100° 400mm 110° 340mm 120° 285mm recommended positions (only for a 2.5m gate or shorter) a value b value 90° or less 205 250 100° 165 2...
Page 23: For V400 (400Mm Operator)
Page 25 alternative positions a and b ‘min value’ gate swing a+b should up to up to up to up to up to up to angle not exceed 1.5m 2m 2.5m 3m 3.5m 4m 60° - 90° or less 455mm 100° 390mm 110° 330mm 120° 275mm recommended positions (only for a 2.5m gate or shorter) a value b value 90° or less 222 246 10...
Page 24: For V400 (400Mm Operator)
Page 25 alternative positions a and b ‘min value’ gate swing a+b should up to up to up to up to up to up to angle not exceed 1.5m 2m 2.5m 3m 3.5m 4m 60° - 90° or less 455mm 100° 390mm 110° 330mm 120° 275mm recommended positions (only for a 2.5m gate or shorter) a value b value 90° or less 222 246 10...
Page 25: Secure Control Box to Wall
Electrical set-up electrical set-up warning 1. Always check that the isolator in the mains supply to the gate is in the off position, before doing any work. 2. Ensure that all low voltage systems (less than 42.4v) are suitably protected from damage, by disconnecting all sources of power such as char...
Page 26: Secure Control Box to Wall
Electrical set-up electrical set-up warning 1. Always check that the isolator in the mains supply to the gate is in the off position, before doing any work. 2. Ensure that all low voltage systems (less than 42.4v) are suitably protected from damage, by disconnecting all sources of power such as char...
Page 27
Figure 10 provides the full menu of features that can be set up on the system. Explanation of each feature is provided in the section “controller features”. When setting up the vector system via the lcd display, all the steps that have to be followed are clearly provided via the display. It is only ...
Page 28
Figure 10 provides the full menu of features that can be set up on the system. Explanation of each feature is provided in the section “controller features”. When setting up the vector system via the lcd display, all the steps that have to be followed are clearly provided via the display. It is only ...
Page 29
Page 30 figure 10 part b of “menu navigation map” page 31 pedestrian open position: 7.1 pedestrian autoclose time: 7.2 pedestrian pre-open delay: 7.3 pedestrian pre-close delay: 7.4 lock enabled status: 8.1 lock type: 8.2 release time: 8.3 pre-release time: 8.4 lock location: 8.5 lock drive (ac/dc):...
Page 30
Page 30 figure 10 part b of “menu navigation map” page 31 pedestrian open position: 7.1 pedestrian autoclose time: 7.2 pedestrian pre-open delay: 7.3 pedestrian pre-close delay: 7.4 lock enabled status: 8.1 lock type: 8.2 release time: 8.3 pre-release time: 8.4 lock location: 8.5 lock drive (ac/dc):...
Page 31
Closed position and via the pcm, push the two gates into the fully closed position, but not past. Short stop value the short stop distance can be set between 1mm and 40mm of piston stroke. Pcm push force the amount of force applied by the actuator when in pcm can be set as a value from 1 to 15. Leaf...
Page 32
Closed position and via the pcm, push the two gates into the fully closed position, but not past. Short stop value the short stop distance can be set between 1mm and 40mm of piston stroke. Pcm push force the amount of force applied by the actuator when in pcm can be set as a value from 1 to 15. Leaf...
Page 33
Page 34 page 35 ramp down distance sets the ramp-down distance in millimeters of travel of the piston when stopping. This setting applies to both motors. Crawl distance sets the final crawl distance in millimeters of travel of the piston when reaching an endpoint. This setting applies to both motors...
Page 34
Page 34 page 35 ramp down distance sets the ramp-down distance in millimeters of travel of the piston when stopping. This setting applies to both motors. Crawl distance sets the final crawl distance in millimeters of travel of the piston when reaching an endpoint. This setting applies to both motors...
Page 35
Page 36 page 37 pedestrian opening – menu 7 this feature is associated with the ped input on the controller. When activating this input, the system will open one of the gates (selectable in a double swing gate installation) to the pedestrian open position, and then automatically close after the pede...
Page 36
Page 36 page 37 pedestrian opening – menu 7 this feature is associated with the ped input on the controller. When activating this input, the system will open one of the gates (selectable in a double swing gate installation) to the pedestrian open position, and then automatically close after the pede...
Page 37
Page 38 diagnostic screen status allow a diagnostic screen to be displayed. Can be useful when troubleshooting, but requires some technical knowledge. Test button disabled allows the round test button on the controller to be disabled, in cases where higher security is required. Remote controls – men...
Page 38
Page 38 diagnostic screen status allow a diagnostic screen to be displayed. Can be useful when troubleshooting, but requires some technical knowledge. Test button disabled allows the round test button on the controller to be disabled, in cases where higher security is required. Remote controls – men...
Page 39
Page 41 page 40 description of terminal functions description of terminal functions s sens1 motor s (mtr s) operator . Connects to the thin purple wire of the motor s operator. S sens2 motor s (mtr s)operator. Connects to the thin blue or orange wire of the motor s operator. M sens1 motor m (mtr m)o...
Page 40
Page 41 page 40 description of terminal functions description of terminal functions s sens1 motor s (mtr s) operator . Connects to the thin purple wire of the motor s operator. S sens2 motor s (mtr s)operator. Connects to the thin blue or orange wire of the motor s operator. M sens1 motor m (mtr m)o...
Page 41: During Normal Operation
Page 42 led external gate status indicator. (a low current output signal.) an output terminal which provides a low current, drive (approx. 4,5v dc, 20ma) to a led which can be used to indicate the gate status remotely. If more than 3 led's are required it is necessary to fit the cp78 multi led drive...
Page 42: During Normal Operation
Page 42 led external gate status indicator. (a low current output signal.) an output terminal which provides a low current, drive (approx. 4,5v dc, 20ma) to a led which can be used to indicate the gate status remotely. If more than 3 led's are required it is necessary to fit the cp78 multi led drive...
Page 43
Charger and pillar light connections charger and pillar light connections page 44 use this procedure to accurately determine the gate opening angle: the following protection fuses are provided on the system: determine gate swing angle determine gate swing angle use gate swing angle of 90 degrees 100...
Page 44
Charger and pillar light connections charger and pillar light connections page 44 use this procedure to accurately determine the gate opening angle: the following protection fuses are provided on the system: determine gate swing angle determine gate swing angle use gate swing angle of 90 degrees 100...
Page 45
Figure 13 wiring diagram for motor m figure 14 wiring diagram for motor s 15 15 15 15 s sens1 s sens2 m sens1 m sense2 sens+ sens- saf clo saf ope com lck/stp trg ped com frx lit led com aux 12v com saf sol light light batt + bat - mtr m+ mtr — mtr s+ mtr s- master slave black black red red blue blu...
Page 46
Figure 13 wiring diagram for motor m figure 14 wiring diagram for motor s 15 15 15 15 s sens1 s sens2 m sens1 m sense2 sens+ sens- saf clo saf ope com lck/stp trg ped com frx lit led com aux 12v com saf sol light light batt + bat - mtr m+ mtr — mtr s+ mtr s- master slave black black red red blue blu...
Page 47
Page 49 com nc no opening beam +12v/24v com nc no irb receiver - 12v/24v 12v or 24v irb tx closing beam +12v/24v irb receiver - 12v/24v 12v or 24v irb tx s sens1 s sens2 m sens1 m sens2 light light batt + batt - mtr m+ mtr m - mtr s+ mtr s - sens+ sens- safe cls safe opn com lck/stp trg ped com frx ...
Page 48
Page 49 com nc no opening beam +12v/24v com nc no irb receiver - 12v/24v 12v or 24v irb tx closing beam +12v/24v irb receiver - 12v/24v 12v or 24v irb tx s sens1 s sens2 m sens1 m sens2 light light batt + batt - mtr m+ mtr m - mtr s+ mtr s - sens+ sens- safe cls safe opn com lck/stp trg ped com frx ...
Page 49
Page 51 wiring diagram for other inputs wiring diagram for other inputs neg +12v/24v com nc no r adio receiver remote control circuitry neg +12v com nc no loop loop detector free exit circuitry holiday lockout keyswitch (normally closed) pillar light pushbutton (normally open) pedestrian keyswitch (...
Page 50
Page 51 wiring diagram for other inputs wiring diagram for other inputs neg +12v/24v com nc no r adio receiver remote control circuitry neg +12v com nc no loop loop detector free exit circuitry holiday lockout keyswitch (normally closed) pillar light pushbutton (normally open) pedestrian keyswitch (...
Page 51
Page 52 wind speeds for which operator will still operate the gate (for v400 or v500 operators) for a 25% covered gate: (palisades, etc.) x 1.8m high value of gate lengths: a or b dimension up to up to up to up to up to up to once installed. #1 1.5m 2m 2.5m 3m(#2) 3.5m(#2) 4m(#2) 100mm 94km/h 66km/h...
Page 52
Page 52 wind speeds for which operator will still operate the gate (for v400 or v500 operators) for a 25% covered gate: (palisades, etc.) x 1.8m high value of gate lengths: a or b dimension up to up to up to up to up to up to once installed. #1 1.5m 2m 2.5m 3m(#2) 3.5m(#2) 4m(#2) 100mm 94km/h 66km/h...