VENOM XT Plus User Instructions - page 6
ear cups and Wireless Transmitter
stop flashing and become a solid
red light.
4.
No future set up is needed.
Setting up your Mac
Fig.5
1.
First connect the Wireless
Transmitter to the Mac: connect
the USB connector into any spare
port on the Mac and the Micro
USB connector into the port on
the Wireless Transmitter.
2.
To connect the Wireless Vibration
Headset XT+ to the Mac: turn on
the power on the Mac and the
Wireless Transmitter will start
flashing red/blue.
3.
Then turn on the power on the
Wireless Vibration Headset XT+
and the LED’s on each ear cup
will also start flashing red. To pair:
simply hold down the pairing
button until you hear a beep on
the headset or both LED’s on
the ear cups and the Wireless
Transmitter stop flashing and
become a solid red light.
4.
Then go to “System Preferences”
> “Sound”.
5.
On the “Output” tab select “2.4G
Wireless Headset”.
6.
On the “Input” tab make sure
“2.4G Wireless Headset” is also
selected.
To charge the Wireless
Vibration Headset XT+
1.
Connect the Micro USB
connector into the port on the
Wireless Vibration Headset XT+
and the other end into any USB
device, either a computer or
mains adaptor.
2.
When charging the indicator is
red; when fully charged the light
will go out.
3.
When charging, please ensure
that the Wireless Vibration XT+
power is turned off to reserve
power.
Battery Information
Your device is powered by a rechargeable
battery. The full performance of a new
battery is achieved only after two or
three complete charge and discharge
cycles. Do not leave a fully charged
battery connected to a charger, since
overcharging may shorten its lifetime. Do
not dispose of batteries in a fire as they
may explode. Please dispose of batteries
according to local regulations and recycle
where possible. Do not dispose as
household waste.
Care and Maintenance
Your device is a product of superior
design and craftsmanship and should be
treated with care. The suggestions below
will help you to protect your warranty
coverage:
• Keep your device out of the reach of
small children.
• Keep the device dry. Precipitation,
humidity and all types of liquid or
moisture can contain minerals that will
corrode electronic circuits. If your device
does get wet, allow it to dry completely.
• Do not use or store the device in
dusty, dirty areas, as moving parts and
electronic components of your device
can be damaged.
• Do not use or store the device in hot
areas. High temperatures can shorten
the life of electronic devices, damage
batteries and warp or melt certain
plastics.
• Do not use or store the device in cold
areas. When the device returns to its
normal temperature, moisture can form
inside the device and damage electronic
circuit boards.
• Do not drop, knock or shake the device.
Rough handling can break internal
circuit boards and fine mechanics.
• Do not use harsh chemicals, cleaning
solvents or strong detergents to
clean the device. All of the previous
suggestions apply equally to your
device, battery, charger or any
enhancements.
Note: parts of the headset are magnetic.
Metallic materials may be attracted to
the headset. Do not place credit cards or
other magnetic storage media near the
headset, as information stored on them
may be erased. Occasionally the headset
may pick up interference from mobile
phones.
Helpline Information:
The helpline is a one-to-one live service.
Hours: 9.00am - 5.00pm
Monday to Thursday
9.00am – 4.30pm Friday
Tel:
+44 (0) 1763 284181
Email:
customerservice@venomuk.com
Website: www.venomuk.com
To ensure that your call is handled quickly
and efficiently please check that you
have the model number VS2854 and any
other relevant information regarding your
product at the time of your call.
VS2854_Wireless Vibration Headset XT+ Instructions A5 2016.indd 11-12
28/06/2016 10:33