- DL manuals
- Wacker Neuson
- Power Tool
- WP 1550A
- Operator's Manual
Wacker Neuson WP 1550A Operator's Manual
Summary of WP 1550A
Page 1
Operator’s manual vibroplate wp 1550a wp 1550aw 5000190169 18 0712 5 0 0 0 1 9 0 1 6 9.
Page 2
Copyright notice © copyright 2012 by wacker neuson corporation. All rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permission from wack...
Page 3: Wp 1550A/aw
Wp 1550a/aw table of contents wpm_bo5000190169_16toc.Fm 3 foreword 3 1. Emission system control information 4 2. Safety information 5 2.1 laws pertaining to spark arresters ...................................................... 5 2.2 operating safety ....................................................
Page 4: Table of Contents
Table of contents wp 1550a/aw wpm_bo5000190169_16toc.Fm 4 5. Maintenance 23 5.1 maintaining the emission control system............................................23 5.2 periodic maintenance schedule ..........................................................23 5.3 cleaning plate .......................
Page 5
Wc_tx000001gb.Fm 5 california proposition 65 warning: engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. Foreword this manual provides information and proce...
Page 6
Emission control system information wpm_tx001755gb.Fm 6 1 emission control systems information and warranty the emission control warranty and associated information is valid only for the u.S.A., its territories, and canada. 1.1 emission control systems warranty statement see the supplied engine owne...
Page 7: Wp 1550A/aw
Wp 1550a/aw safety information wpm_si000327gb.Fm 7 2. Safety information this manual contains danger, warning, caution, notice, and note signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It...
Page 8: Safety Information
Safety information wp 1550a/aw wpm_si000327gb.Fm 8 2.2 operating safety familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be hazardous. Read the operating instructions contained in this manual and the engine...
Page 9: Wp 1550A/aw
Wp 1550a/aw safety information wpm_si000327gb.Fm 9 2.3 operator safety while using internal combustion engines internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Fail...
Page 10: Safety Information
Safety information wp 1550a/aw wpm_si000327gb.Fm 10 2.4 service safety a poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 2.4.1 do not attempt to clean ...
Page 11: Wp 1550A/aw
Wp 1550a/aw safety information wpm_si000327gb.Fm 11 2.5 label locations wpmgr005961 1 2 3 4 5 6 7 1 2 warning warnung advertencia avertissement 10w30
Page 12: Safety Information
Safety information wp 1550a/aw wpm_si000327gb.Fm 12 2.6 warning and informational labels wacker neuson machines use international pictorial labels where needed. These labels are described below. Label meaning warning! To prevent hearing loss, wear hearing protec- tion when operating the machine. Rea...
Page 13: Wp 1550A/aw
Wp 1550a/aw safety information wpm_si000327gb.Fm 13 warning! Hand injury if caught in moving belt. Always replace beltguard. Caution! Read and understand the supplied operator’s manual before operating this machine. Failure to do so increases the risk of injury to yourself and others. Notice lifting...
Page 14: Safety Information
Safety information wp 1550a/aw wpm_si000327gb.Fm 14 company logo a nameplate listing the model number, item number, revision number, and serial number is attached to each unit. Please record the infor- mation found on this nameplate so it will be available should the nameplate become lost or damaged...
Page 15: Wp 1550A/aw
Wp 1550a/aw safety information wpm_si000327gb.Fm 15 2.7 operating labels wacker neuson machines use international pictorial labels where needed. These labels are described below. Label meaning open the fuel flow valve. Push or turn engine switch to on position. Close the choke. Place throttle in the...
Page 16: Safety Information
Safety information wp 1550a/aw wpm_si000327gb.Fm 16 push or turn engine switch to off position. Open the choke. Place throttle in the fast position. Throttle control lever: turtle = idle or slow rabbit = full or fast label meaning 1.
Page 17: Wp 1550A/aw
Wp 1550a/aw technical data wpm_td000336gb.Fm 17 3. Technical data 3.1 engine data engine power rating net power rating per sae j1349. Actual power output may vary due to conditions of specific use. Wp 1550a/aw 0007576, 0007579, 0009486, 0009546 engine engine make honda engine model gx 160 ut1 qwx2 m...
Page 18: Technical Data
Technical data wp 1550a/aw wpm_td000336gb.Fm 18 3.2 plate data 3.3 sound and vibration specifications products are tested for sound pressure level in accordance with en iso 11204. Sound power level is tested in accordance with european directive 2000/14/ec - noise emission in the environment by equi...
Page 19: Wp 1550A/aw
Wp 1550a/aw technical data wpm_td000336gb.Fm 19 3.4 dimensions mm (in.) 19.5 (500) 34.5 (875) 38 (965) wpmgr005986.
Page 20: Operation
Operation wp 1550a/aw wpm_tx001131gb.Fm 20 4. Operation 4.1 recommended fuel the engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage fuel system. Consult engine owner’s manual for complete fuel specifications. Use of oxygenat...
Page 21: Wp 1550A/aw
Wp 1550a/aw operation wpm_tx001131gb.Fm 21 4.3 to start see graphic: wc_gr000014 4.3.1 open fuel valve by moving lever to the right (a1). Note: if engine is cold, move choke lever to close position (b1). If engine is hot, set choke to open position (b2). 4.3.2 turn engine switch to “on” (e1). 4.3.3 ...
Page 22: Operation
Operation wp 1550a/aw wpm_tx001131gb.Fm 22 4.5 application this plate is designed for compacting loose, granular soils, gravel, and paving stones. It is intended to be used in confined areas and areas next to structures such as walls, curbs, and foundations. Plates equipped with water tanks can be u...
Page 23: Wp 1550A/aw
Wp 1550a/aw operation wpm_tx001131gb.Fm 23 4.6 operation see graphic: wpmgr006016 run engine at full throttle and allow plate to pull itself along at its normal speed. When operating on an incline it may be necessary to assist plate by pushing it forward slightly. Depending on the material being com...
Page 24: Operation
Operation wp 1550a/aw wpm_tx001131gb.Fm 24 4.7 wheel kit (0162986) see graphic: wc_gr002793 wheel kit (part no. 0162986) is a standard item on item number 0009545, 0009546, 0009547 and 0009548 only. Available as an option on all other models. 4.7.1 disengage wheel kit from holding latch (a) and posi...
Page 25: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 25 5. Maintenance 5.1 maintaining the emission control system normal maintenance, replacement, or repair of emission control devices and systems may be performed by any repair establishment or individual; however, warranty repairs must be performed by a deal...
Page 26: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 26 5.2.2 machine maintenance the chart below lists basic machine maintenance. Note: when machine is being used in asphalt, it is highly recommended that shockmounts are replaced every year or after 300 hours of usage. Daily before starting after first 20 hrs...
Page 27: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 27 5.3 cleaning plate clean plate after use to remove dirt, stones, and mud caught under the engine console. If plate is being used in a dusty area, check engine cylinder cooling fins for heavy dirt accumulation. Keep engine cylinder fins clean to prevent en...
Page 28: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 28 5.5 exciter lubrication see graphic: wpmgr006021 the exciter assembly is a self-contained, sealed unit. The bearings are lubricated using automatic transmission fluid (see technical data for type). Change fluid once every year or 300 hours of operation. W...
Page 29: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 29 5.6 spark plug see graphic: wc_gr000028 clean or replace the spark plug as needed to ensure proper operation. Refer to your engine operator’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Do n...
Page 30: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 30 5.7 engine oil see graphic: wc_gr000022 5.7.1 drain the oil while the engine is still warm. 5.7.2 remove the oil filler plug (a) and the drain plug (b) to drain the oil. Note: in the interests of environmental protection, place a plastic sheet and a conta...
Page 31: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 31 5.8 air cleaner see graphic: wc_gr000025 the engine is equipped with a dual element air cleaner. Service air cleaner frequently to prevent carburetor malfunction. Notice : never run engine without air cleaner. Severe engine damage will occur. Never use ga...
Page 32: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 32 5.9 cleaning sediment cup see graphic: wc_gr000029 5.9.1 turn the fuel valve off. 5.9.2 remove the sediment cup (a) and the o-ring (b). 5.9.3 wash both thoroughly in a nonflammable solvent. Dry and reinstall them. 5.9.4 turn the fuel valve on and check fo...
Page 33: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 33 5.10 carburetor adjustment see graphic: wc_gr000032 5.10.1 start the engine and allow it to warm up to operating temperature. 5.10.2 set the pilot screw (a) two turns out. See note. 5.10.3 with the engine idling, turn the pilot screw (a) in or out to the ...
Page 34: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 34 5.11 troubleshooting problem / symptom reason / remedy plate does not develop full speed. Poor compaction. • engine throttle control not completely open. • throttle control not adjusted correctly. • ground too wet, plate sticking. Allow soil to dry before...
Page 35: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 35 5.12 storage if plate is being stored for more than 30 days: 5.12.1 remove loose stones and dirt from plate. 5.12.2 clean engine cylinder cooling fins. 5.12.3 clean or replace air filter. 5.12.4 change exciter oil. 5.12.5 change engine oil and follow proc...
Page 36: Maintenance
Maintenance wp 1550a/aw wpm_tx001132gb.Fm 36 5.13 lifting machine see graphic: wpmgr006037 see technical data for the weight of the machine. To lift machine manually: 5.13.1 stop the engine. 5.13.2 obtain help from a partner and plan the lift. 5.13.3 grasp the machine by its cage (a) and lifting slo...
Page 37: Wp 1550A/aw
Wp 1550a/aw maintenance wpm_tx001132gb.Fm 37 5.14 transporting machine see graphic: wpmgr006055 to avoid burns or fire hazards, let engine cool before transporting machine or storing indoors. 5.14.1 turn fuel valve to the off position and keep the engine level to prevent fuel from spilling. 5.14.2 t...
Page 39
Heinz gengnagel president & ceo wacker neuson manila inc. Date wp 15 50 -e n_ 20 11_ w n .Fm the original language of this ec declaration of conformity is american english. Ec declaration of conformity wacker neuson manila, inc., dasmariÑas, cavite, philippines hereby certifies that the construction...
Page 42
Wacker neuson se, preußenstraße 41, d-80809 münchen, tel.: +49-(0)89-3 54 02-0 fax: +49 - (0)89-3 54 02-390 wacker neuson production americas llc, n92w15000 anthony ave., menomonee falls, wi 53051 tel. : (262) 255-0500 fax: (262) 255-0550 tel.: (800) 770-0957 wacker neuson limited - room 1701–03 & 1...