WAGNER Project 115 Owner's Manual - page 22
18
Wagner Project 115 - 0418A
Figure20-CleaningtheInletValve(Kitpartnumber
0418714)
i
Cleaning or servicing the inlet valve may be required if
the unit has priming problems. Priming problems may
be prevented by properly cleaning the sprayer and
following the long-term storage steps.
Danger
Perform the Pressure Relief Procedure (see figure 7) and
unplug the sprayer.
1. Removethehopper.Loosenthelocknutbyturning
anticlockwise.
2. Remove the inlet sleeve (1) with a suitable tool (e.g. socket SW
11).
3. Inspect the threads on the inlet sleeve and the inlet sleeve
O-ring(2).Removeanyaccumulatedpaint.
4. Toremovetheinletvalve,placetheassemblyaid(8)ona
socket (6) with a 5/8” insert (7). Insert the inlet valve tool into
theinletvalve(a).Removetheinletvalvescrewconnectionby
unscrewing anticlockwise from the housing.
5. Retrievetheinletvalve(9)andtheinletvalveO-ring(10)from
the inlet valve housing. Clean or replace and lubricate the
O-ringwithalighthouseholdoil.
6. SettheinletvalveO-ring(10)backintothehousing,andset
the inlet valve (9) on top of it.
7. Replace inlet fitting (8) into the housing. Tighten with the
inlet valve tool (7) and ratchet (4, 5, 6).
8. Replacetheseal(3).PlacetheinletsleeveO-ring(2)onto
theinletvalvefitting(9),andreplacetheinletsleeve(1)by
twisting it clockwise.
9. Replace the hopper.
Figure21-CleaningtheOutletValve
Cleaning or replacing the outlet valve may be necessary if your
spray performance remains poor after having performed all the
steps contained in the Troubleshooting section of this manual.
Danger
Perform the Pressure Relief Procedure (see figure 7) and
unplug the sprayer.
1. Unscrew the outlet valve from the outlet valve housing using
an adjustable wrench.
2. Inspecttheinsideoftheoutletvalvehousing(a).Cleanany
accumulated paint.
3. Replace with a new outlet valve. Tighten into outlet valve
housing with an adjustable wrench.
Parts Lists
Figure22-SprayGun/SprayHose
Item Part #
Description
Quantity
1 0418717
Gunassembly(withoutnozzle) ....................1
2 0418705
Tip, XS ......................................................................1
2 0418707
Tip, M .......................................................................1
3 0418711
Filter, XS-S (red) ...................................................2
3 0418712
Filter,M(yellow) ..................................................2
4 0418718
Sprayhose,7.5m,red ........................................1
Part #
Description
0418705
Spraytip,XS .....................Water-soluble and solvent
based enamels and paints, oils
and release agents
0418706
Spraytip,S .......................Syntheticresin-basedpaints,
PVC paints
0418707
Spraytip,M ......................Enamel paints, undercoats,
primers, fillers, indoor latex
paints and indoor emulsions
0418708
Spraytip,L .......................Enamel paints, undercoats,
primers, fillers, indoor latex
paints and indoor emulsions,
anti-corrosive paints
0418711
Filter, XS - S (red, 2 pack)
0418712
Filter,M(yellow,2pack)
0418713
Filter,L-XXL+(white,2pack)
0418714
Valve set (inlet and outlet valve)
All spare parts listed above are wear parts, and are not covered
by warranty!