Wasco LS 1003 E User Manual - 2 Installation
19/EN
Washing Machine / User’s Manual
2 Installation
Refer to the nearest Authorised Service Agent for installation
oftheproduct.Tomaketheproductreadyforuse,review
the information in the user manual and make sure that the
electricity,tapwatersupplyandwaterdrainagesystemsare
appropriatebeforecallingtheAuthorizedServiceAgent.If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparationofthelocationandelectrical,tapwaterand
wastewaterinstallationsattheplaceofinstallationis
undercustomer'sresponsibility.
B
warning
:
Installation and electrical connections of
theproductmustbecarriedoutbytheAuthorized
ServiceAgent.Manufacturershallnotbeheldliablefor
damages that may arise from procedures carried out by
unauthorizedpersons.
A
warning
:
Priortoinstallation,visuallycheckiftheproduct
has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
C
Makesurethatthewaterinletanddischargehoses
aswellasthepowercablearenotfolded,pinchedor
crushedwhilepushingtheproductintoitsplaceafter
installation or cleaning procedures.
2.1 Appropriate installation location
• Placethemachineonarigidfloor.Donotplaceitona
long pile rug or similar surfaces.
• Totalweightofthewashingmachineandthedryer-with
fullload-whentheyareplacedontopofeachother
reachestoapprox.180kilograms.Placetheproduct
on a solid and flat floor that has sufficient load carrying
capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductatplaceswheretemperature
mayfallbelow0ºC.
• Placetheproductatleast1cmawayfromtheedgesof
other furniture.
2.2 Removing packaging reinforcement
Tiltthemachinebackwardstoremovethepackaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
2.3 Removing the transportation locks
A
warning
:
Do not remove the transportation locks before
taking out the packaging reinforcement.
A
warning
:
Remove the transportation safety bolts before
operatingthewashingmachine!Otherwise,theproduct
willbedamaged.
1.Loosenalltheboltswithasuitablespanneruntilthey
rotate freely
(C)
.
2. Remove transportation safety bolts by turning them
gently.
3.AttachtheplasticcoverssuppliedintheUserManualbag
into the holes on the rear panel.
(P)
C
Keep the transportation safety bolts in a safe place to
reusewhenthewashingmachineneedstobemoved
again in the future.
C
Nevermovetheproductwithoutthetransportationsafety
boltsproperlyfixedinplace!
2.4 Connecting water supply
C
Thewatersupplypressurerequiredtoruntheproductis
between1to10bars(0.1–1MPa).Itisnecessaryto
have10–80litersofwaterflowingfromthefullyopen
tap in one minute to have your machine run smoothly.
Attachapressurereducingvalveifwaterpressureis
higher.
C
Ifyouaregoingtousethedoublewater-inletproduct
as a single
(cold)
water-inletunit,youmustinstallthe
suppliedstoppertothehotwatervalvebeforeoperating
theproduct.(Appliesfortheproductssuppliedwitha
blind stopper group.)
A
warning
:
Modelswithasinglewaterinletshouldnotbe
connectedtothehotwatertap.Insuchacasethelaundry
willgetdamagedortheproductwillswitchtoprotection
modeandwillnotoperate.
A
warning
:
Donotuseoldorusedwaterinlethosesonthe
newproduct.Itmaycausestainsonyourlaundry.
1.Connectthespecialhosessuppliedwiththeproductto
thewaterinletsontheproduct.Redhose(left)(max.90
ºC)isforhotwaterinlet,bluehose(right)(max.25ºC)is
forcoldwaterinlet.
A
warning
:
Ensurethatthecoldandhotwaterconnections
aremadecorrectlywheninstallingtheproduct.
Otherwise,yourlaundrywillcomeouthotattheendof
thewashingprocessandwearout.
2.Tightenallhosenutsbyhand.Neveruseatoolwhen
tightening the nuts.
3.Openthetapscompletelyaftermakingthehose
connectiontocheckforwaterleaksattheconnection