Watchguard CHG400 User Manual - Introduction

Manual is about: LRT WIRELESS MICROPHONE

Summary of CHG400

  • Page 1

    Lrt wireless microphone user guide wgd00091 revision a.

  • Page 2

    - 2 - wgd00091 revision a fcc and ic notices this equipment complies with part 15 of the fcc rules and industry canada licence- exempt rss standard(s). Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Cet équipement est...

  • Page 3: Table of Contents

    Wgd00091 - 3 - revision a table of contents introduction.......................................................................................................... 5 general operation ................................................................................................ 5 installation ........

  • Page 4

    - 4 - wgd00091 revision a c ompatibility ................................................................................................................. 17 u sing m ultiple w ireless s ystems ................................................................................... 17 p otential s ources...

  • Page 5: Introduction

    Wgd00091 - 5 - revision a introduction this is the user guide for the watchguard video long range transmitter (lrt) wireless microphone. The lrt microphone is a specialized device designed to be used exclusively with watchguard’s family of vehicle-based digital video recorder (dvr) products. This gu...

  • Page 6: Installation

    - 6 - wgd00091 revision a installation important: please turn off the power to the digital video system before connecting or disconnecting any microphone system cables. Please reference figure 1 during the installation process. Reference the watchguard video “microphone installation instructions – d...

  • Page 7: Dvr Cable Connection

    Dvr cable connection connect the supplied digital video recording (dvr) system interface cable to this point. This cable supplies power from the dvr to the base device when the dvr power is turned on. This cable also transfers the audio signal from the microphone system to the dvr for inclusion in t...

  • Page 8: Base Unit Features

    Base unit features red and green status leds please reference figure 2. The green led on the base will light when communicating with the transmitter device. The led will light solid green when a voice recording is enabled. During a voice recording, this led will flash when the transmitter is muted. ...

  • Page 9

    Until the contacts on the bottom of the transmitter (figure 5) connect with the contacts on the base (figure 3). The base and transmitter leds will flash briefly. After a few seconds, the binding process is complete. The base and transmitter are now ready for normal use. Figure 3: base top view figu...

  • Page 10: Transmitter Unit Features

    System controls and features transmitter unit features transmitter power on/off refer to figure 5. Use this switch to turn the transmitter device power on and off. This switch must be in the on position for all transmitter- recording functions to operate properly. Figure 5: transmitter bottom talk/m...

  • Page 11: Status Indicators

    Keep the recording enabled but there will be no voice audio present in the recording. Release the slide switch to re-enable the voice audio; the transmitter led will go back to a solid green led. Figure 6: transmitter front status indicators refer to figures 7 and 8. Battery level indicator this ico...

  • Page 12: Vibration Mode Status

    Vibration mode status this icon shows when the vibration notification mode is selected. Beeper mode status this icon shows when the beep notification mode is selected. Lcd backlight control button press this button to turn on the lcd backlight. This will allow the lcd status icons to be more easily ...

  • Page 13: Covert Mode

    Covert mode covert mode disables all light and sound coming from the transmitter device. To enter covert mode, hold the mode button down for 3 seconds. Once in covert mode, the lcd backlight, green led and red led will be disabled. The lcd status icon will still show the current status of the system...

  • Page 14: Lapel Microphone Jack

    Lapel microphone jack refer to figure 10. Connect the accessory lapel microphone to this jack. Figure 10: transmitter right side transmitter belt clip refer to figure 11. To attach one of the accessory belt clips to the transmitter, position the clip in the clip mount slot on the back of the transmi...

  • Page 15: Set Up And Operation

    Wgd00091 - 15 - revision a set up and operation binding the transmitter and base 1. Ensure the dvr is installed properly and the rj-45 signal cable is connected to the microphone base. 2. Turn on the dvr power. 3. Turn the microphone transmitter power switch to on and place the transmitter in the re...

  • Page 16: Low Battery Warning

    - 16 - wgd00091 revision a low battery warning if the transmitter beeps and the red led flashes, return the transmitter to its base charging cradle to fully charge the transmitter. The base’s led indicator will light constant green when the unit is fully charged..

  • Page 17: Best Performance

    Wgd00091 - 17 - revision a guidelines and recommendations for best performance compatibility the transmitter and base must be bound to work together by placing the transmitter into the charging cradle of the base while the base power is on. The base and the transmitter’s leds will flash until bindin...

  • Page 18: Technical Specifications

    Technical specifications operating voltage transmitter: 3.7vdc base: 12vdc frequency 900mhz (902.25 ~ 928.00 mhz) – 52 channels, digital spread spectrum operating range 1 mile in open line of sight * note : operating range can be different according to the environment led indicators transmitter: low...

  • Page 19: Warranty

    Wgd00091 - 19 - revision a warranty watchguard video, in recognition of its responsibility to provide quality systems, components, and workmanship, warrants each system, part, and component it manufactures first sold to an end user to be free from defects in material and workmanship for a period of ...

  • Page 20

    - 20 - wgd00091 revision a component(s) pursuant to this warranty shall be warranted for the remainder of the warranty period applicable to the system warranty period. Shipping – during the first ninety (90) days of the initial warranty period, watchguard video will provide a prepaid shipping label ...