Water Right Clear Flo Installation, operation & service manual - page 12
12
4. Tosanitizethesystemandreplacethefilters:
NOTE: The system should be sanitized
beforeinstallingtheSedimentPrefilterand
ActivatedCarbonPrefilter.
•Use a good quality unscented 5¼% liquid
chlorine household bleach.
•Add one capful of bleach (this is 2 tsp. or
10ml)totheSedimentPrefilterHousing
and temporarily install the Housing without
theSedimentPrefilter.AVOIDGETTING
BLEACH ON THREADS AND O-RINGS.
Check the Housing O–ring for proper
positioninitsgroove,engageandfirmly
tighten the Housing hand tight only.
•Add one capful of bleach to the Activated
CarbonPrefilterHousing.AVOIDGETTING
BLEACH ON THREADS AND O-RINGS.
CarefullyfilltheHousingwithtapwaterand
temporarily install the Housing without the
ActivatedCarbonPrefilter.
•The Dispensing Faucet should be open,
slowly open the Feed Water Saddle Valve.
•As soon as water begins to drip out of the
Dispensing Faucet, close the Faucet.
•Let the system stand for 15 minutes.
•At the end of 15 minutes, in the following
order, close the Feed Water Saddle Valve,
close the Holding Tank Valve and open the
Dispensing Faucet to release the pressure.
•RemovetheSedimentPrefilterHousingand
empty. Remove the wrapping and install
theSedimentPrefilter.Firmlytightenthe
Housing hand tight only.
•RemovetheActivatedCarbonPrefilter
Housing and empty. Remove the wrapping
andinstalltheActivatedCarbonPrefilter.
Firmly tighten the Housing hand tight only.
•Disconnect the yellow product water tubing
that runs from the Holding Tank to the
Tee (see Fig. 1). Put 50 drops of bleach
(this is ½ tsp. or 3 ml) into the tubing and
reconnect it to the Tee.
NOTE: Now is the convenient time to
change the In–Line Activated Carbon Post
Filter, see Sec. V, C.1–6.
•Slowly open the Feed Water Saddle Valve.
When water begins dripping out of the
Dispensing Faucet, in the following order,
close the Faucet and then open the Holding
Tank Valve.
•Do not open the Faucet for at least 8 hours.
•Discardthefirstthreefulltanksofwater
produced, they will contain chlorine.
IN–LINE ACTIVATED CARBON
POST FILTER ASSEMBLY
OUT
IN
In-Line Activated
Carbon Post Filter
3/8" Blue
To
Dispensing
Faucet
3/8" Blue
Figure 5
C. Changing the In–Line Activated Carbon Post
Filter
1. Close the Feed Water Saddle Valve by
turning fully clockwise.
2. Close the Holding Tank Valve and then
open the Dispensing Faucet to release the
pressure.
3. Remove the In–Line Activated Carbon Post
Filter. Disconnect the used Post Filter by
pressingintheconnector’scollarandatthe
sametimepullingthetubeoutofthefitting.
4. Firmly reconnect the polytubes to the new
Post Filter. (Refer to Fig. 5.) Make sure the
tubing is pressed all the way in to create a
pressure tight connection.
NOTE: If you want to pull the tubing out for some
reason, push the ring around the tubing in
and pull the tubing out.
5. Slowly open the Feed Water Saddle Valve.
6. When water begins dripping out of the
Faucet, in the following order, close the
Faucet and open the Holding Tank Valve.
WhentheFaucetisfirstopened,expectair
andcarbonfines(veryfineblackpowder),
from the new Post Filter to be rinsed out. This
isnormalforthefirsttankofwater.