1. DL manuals
  2. Waterco
  3. Water Filtration Systems
  4. Commandomatic Ezysoft
  5. Manual For Use And Installation

Waterco Commandomatic Ezysoft Manual For Use And Installation

Manual is about: WATER SOFTENER SYSTEM Ezysoft semi automatic domestic water softeners

Summary of Commandomatic Ezysoft

  • Page 1

    Www.Waterco.Com notice to installer this manual contains important information about the installation, operation and safe use of this product. Once the product has been installed this manual must be given to the owner / operator of this equipment. This equipment must be installed and serviced by a q...

  • Page 2

    Table of introduction --------------------------------------------------- 03 1. General information ---------------------------------- 03 1.2. Water softeners -------------------------------------- 03 1.3. Advantages of using ezysoft --------------------- 03 1.4. Key features -----------------------...

  • Page 3

    Waterco commandomatic ezysoft warning & safety instructions • before you begin the installation of the water softener, we advise you read and carefully follow the instructions contained in this manual. It contains important information about safety, installation, use and maintenance of the product. ...

  • Page 4

    For future reference, fill in the following data installation record serial number : model : water hardness inlet : water hardness outlet : water pressure inlet : date of installation : company name : installer name : phone number : regen. Frequency : ________ days length of regen. : _________ minut...

  • Page 5: Introduction

    Waterco commandomatic ezysoft i pg 03 introduction this booklet is designed to cover the waterco ezysoft semi automatic domestic water softeners. 1. General information 1.2. Water softeners hard water contains dissolved minerals in the form of calcium (ca), magnesium (mg), and iron (fe). Removal of ...

  • Page 6

    2. Operating conditions and requirements • operating pressure: min. 140 / max. 830 kpa − this system is configured to perform optimally at an operating pressure of 300 kpa (±50 kpa); in case of a lower or higher operating pressure the performance may be affected negatively. − check water pressure re...

  • Page 7: 3. How The System Works

    Waterco commandomatic ezysoft i pg 05 3. How the system works the commandomatic ezysoft is a semi-automatic water softener. When the drain paddle is opened, the valve is automatically transferred to the regeneration position; with its few moving parts, this simple and reliable system guarantees year...

  • Page 8: 4. Installation

    4. Installation to facilitate the installation process, remove the salt lid and main cover from the water softener. 4.2. Connecting inlet & outlet i. Screw the factory bypass onto the elbow connections of the water softener (2&3); make sure to install the gasket seals. Tighten the nuts firmly by han...

  • Page 9

    Waterco commandomatic ezysoft i pg 07 4.3. The drain i. Connect a 13 mm hose to the drain of the control valve (1); secure it by means of a clamp. Ii. Run the drain hose to the sewerage system and connect it to the stand pipe assuring sufficient air gap. This drain line operates under pressure, so i...

  • Page 10: 5. Start Up

    5. Start up when installation has been completed, the unit is ready to be placed into service. Proceed as follows, while checking the unit for any leakages: i. Place unit in bypass and turn on main water supply; open a cold water tap nearby and allow water to run for a few minutes until all foreign ...

  • Page 11: 6. Initiate A Regeneration

    Waterco commandomatic ezysoft i pg 09 6. Initiate a regeneration the semi-automatic timer must be manually initiated; by turning the timer knob clockwise past 30 min, the drain paddle is opened and the valve is transferred to the brine/slow rinse position; the length of this cycle can then be set be...

  • Page 12

    A calculation can be made to estimate usage, to enable a regeneration schedule to be prepared. Each person will use approximately 125 litres of water per day. An automatic washing machine and/ or dishwasher each counts as an additional user. Example: calculate the days between regeneration for a fam...

  • Page 13: 8. Maintenance

    Waterco commandomatic ezysoft 8. Maintenance 8.2. Bypassing the water softener occasionally it may be necessary to put the unit hydraulically in bypass, i.E. To isolate it from the water distribution system; e.G.: • in case of an urgent technical problem; • when it needs to be removed for maintenanc...

  • Page 14: 9. Parts Replacement

    8.3. Adding salt be sure to use commandomatic salt (approximately 1/4” pellets), as it is specially selected large granule salt, graded for maximum efficiency and packed in 25kg moisture proof bags. This will prevent “bridging”, as would occur if fine salt were used. Your brine tank holds 50kg – or ...

  • Page 15

    Waterco commandomatic ezysoft 9.2. Injector i. Remove the 3 screws holding the injector cover plate in place. Ii. Lift off the injector cover plate. Iii. Remove the injector and injector gasket. Iv. Remove the injector filter and check for dirt or clogging. V. Install the injector filter. Vi. Instal...

  • Page 16

    9.6. Body stem assembly i. Remove the drain hose from the drain line fitting. Ii. Remove the 4 timer head screws and pull away the timer head assembly. Iii. Pull forward the main diaphragm; put 2 fingers behind the membrane and pull out the body stem assembly. Iv. Inspect the centre check disc rubbe...

  • Page 17: 10. Troubleshooting

    Waterco commandomatic ezysoft xii. Lubricate the threads, the top of the riser tube and the tank o-ring of the control valve. Xiii. Lower the control valve straight down onto the riser tube and screw it onto the tank. Xiv. Install the drain hose to the drain line fitting and the brine line to the br...

  • Page 18

    Valve fails to draw brine cause solution 1. Low operating pressure 1. Verify operating pressure; must exceed 140kpa 2. Drain flow adjuster too much closed 2. Open drain flow adjuster slowly until unit draws brine 3. Plugged injector 3. Clean injector 4. Plugged injector filter 4. Clean injector filt...

  • Page 19

    Waterco commandomatic ezysoft i pg 17 drain flow adjuster !!! Attention when the valve is equipped with an incorporated drain flow control (optional), the drain flow adjuster is when the valve is equipped with an incorporated drain flow control (optional), the drain flow adjuster is assembled and lo...

  • Page 20: 11. Exploded Diagrams

    11. Exploded diagrams 11.2. System explode diagram (include components of fully automatic units).

  • Page 21

    Waterco commandomatic ezysoft parts list (system) 12.2 valve body i pg 19 item part number description 1 72515760 pressure tank, 9x35 2 softening resin 3 72515771 riser tube assembly with deflector 4 72515767 top distributor 5 72515770 connection kit ¾” male 6 377872640 control valve assembly 7 7251...

  • Page 22

    Parts list (system) item part number description 1 screw, back cap (4x) 2 back cap 3 gasket, back cap 4 spring, check disc 5 check disc 6 screw, cover plate (3x) 7 cover plate, injector 8 72515774 injector disc #5 9 72515775 gasket, injector 10 72515776 filter, injector 11 locking plate, drain flow ...

  • Page 23: 12. Technical Specifications

    Waterco commandomatic ezysoft 12. Technical specifications operating pressure min/max (kpa) 140/830 operating temperature min/max (°c) 2/48 electrical connection (v/hz) none maximum power consumption (va) none hydraulic connection inlet/outlet ¾” bsp male performances @ 3 bar operating pressure and ...

  • Page 24

    Waterco limited abn 62 002 070 733 (zzm1448) 02/2013 offices - australia nsw - sydney (head office) tel : +61 2 9898 8686 vic/ tas - melbourne tel : +61 3 9764 1211 wa - perth tel : +61 8 9273 1900 qld - brisbane tel : +61 7 3299 9900 sa/ nt - adelaide tel : +61 8 8244 6000 act distributor tel : +61...