WaterFurnace TPCM32U03 Instruction Manual

1

INSTRUCTION GUIDE: ElITE COmmUNICaTING ThERmOSTaT

IG1602EW    06/12

Instruction Guide:

Elite Communicating Thermostats

TPCm32U03/TPCm32U04

Thermostat Operation

NOTE: These communicating thermostats communicate via a 

4-wire modbus protocol and will only operate with the aurora 

Control System. TPCm32U03 is not applicable to variable speed 

compressor equipment.

Adjusting Temperature

(Temporary Override in Programmable models)

1.  Before you can adjust the temperature, a mODE must be 

selected. If you are already in a heating or Cooling mode, 

then skip to step 5.

2.  To select a mODE, use the keypad 

arrows to scroll to mODE, and then 

press the center button on the key 

pad to enter the operating mode 

menu.

3.  Select the desired mode by 

scrolling up or down, with the 

arrows, and then press the center 

button on the keypad to enter into that mode.

4.  You are now returned to the main menu and Figure 1 is a 

similar view. 

NOTE: Outdoor temperature is only displayed 

if an outdoor sensor is installed.   

5.  To increase the temperature set point, use the arrow up 

button. To decrease the set point, use the arrow down 

button. Press the center button on the key pad for the new 

set point to be effective 

Setting Date And Time

1.  From the main menu, scroll to mENU and press the center 

button ■ on the keypad.

2.  Select SET DaTE aND TImE

3.  If your area observes daylight savings time, select aUTO 

DaYlIGhT SaVING, scroll to ON, then press the center 

button ■ to save. You will be returned to the select SET 

DaTE aND TImE menu. Scroll to SET DaTE aND TImE 

and press the center button ■ on the keypad.

4.  SET MONTH by using the up and down arrows ▲▼, and then 

press the center button on the keypad to save the month.

5.  SET DAY by using the up and down arrows ▲▼, and then 

press the center button on the keypad to save the day.

6.  SET YEAR by using the up and down arrows ▲▼, and then 

press the center button on the keypad to save the year.

7.  SET HOUR by using the up and down arrows ▲▼, and then 

press the center button on the keypad to save the hour.

8.  SET MINUTE by using the up and down arrows ▲▼, and 

then press the center button ■ on the keypad to save the 

minute.

9.  Date and Time are now set. You can return to the main 

menu by pressing the left arrow key to return to the 

previous menu.

Hold Setting

Vacation and Permanent (Programmable models only)

This section describes the hOlD functions. You can program 

the thermostat to hold the temperature for a period of time. 

If you want to hold the temperature for a few hours or a few 

weeks, your thermostat can accommodate your schedule. 

Vacation Hold

(Programmable models only)

1.  From the main menu, scroll to mENU and press the center 

button ■ on the keypad.

2.  Select HOLD → VACATION

3.  First, the thermostat prompts you for a temperature to hold. 

If you are in aUTO mODE you will be prompted for both 

a heat setting and a cool setting. Use the up and down 

arrows keys ▲▼ to select the desired temperature and 

press the center button on the keypad. 

4.  Next it will prompt you for a date and time that you wish 

to return to programmed operation. Returning to the main 

Screen, you will notice that in the upper part of the screen 

is alternating hOlD TIl *date and time you specified* and 

the actual date and time.

5.  To cancel this hold, scroll to CaNCEl hOlD from the main 

Menu and press the center button ■. 

Permanent Hold

(Programmable models only)

1.  From the main menu, scroll to mENU and press the center 

button ■ on the keypad.

2.  Select HOLD → PERMANENT

3.  First, the thermostat prompts you for a temperature to hold. 

If you are in aUTO mODE you will be prompted for both 

a heat setting and a cool setting. Use the up and down 

arrows keys ▲▼ to select the desired temperature and 

press the center button on the keypad. 

4.  Returning to the main Screen, you will notice that in the 

upper part of the screen is alternating PERmaNENT hOlD 

and the actual date and time. 

5.  You can adjust to permanent hold temperature at will, and 

the temperature you select will remain until the permanent 

hold is canceled. 

6.  To cancel this hold, scroll to CaNCEl hOlD from the main 

Menu and press the center button ■. This will revert to the 

programmed settings.

Figure 1

Elite Communicating Thermostats

TPCM32U03/TPCM32U04