Watkins Hot Spot Owner's Manual - page 17
Page 14
Operating Instructions
JET PUMP CONTROL
Pressing the Jet button changes the jet pump functions, depending on the number of presses:
Mallorca
®
Spa only:
1st press:
Two-speed jet pump runs on low speed
2nd press:
Two-speed jet pump runs on high speed
3rd press:
One-and Two speed jet pumps run on high speed
4th press:
One-speed jet pump runs on high speed
5th press:
Both jet pumps are off.
Sorrento
®
, Trinidad
®
, and Tobago
®
Spas only:
1st press:
Two-speed jet pump runs on low speed
2nd press:
Two-speed jet pump runs on high speed
3rd press:
Jet pump off
• During filter cycles or when the thermostat is calling for heat, the pump’s low speed operates automatically and cannot be turned off by
pressing the Temp Up (
▲) or Temp Down (▼) touch pad.
• The pump on high speed automatically turns off after operating for two hours. The pump on low speed automatically turns off after operating
for two hours.
• When the jets are active, the JETS Icon on the control panel will illuminate.
LIGHT CONTROL
Your Hot Spot
®
spa is equipped with a blue LED spa light. Press the LIGHT button to turn it on. The light automatically
turns off after six hours. When the light is active, the LIGHT Icon on the control panel will illuminate. Press it a second
time to turn the light to a medium light intensity, a third time for a low light intensity and a fourth time will turn it off. For
enhanced spa enjoyment, an optional six color wheel light feature is available to create your desired ambience.
SPLENDORS
®
LED LIGHTING (OPTIONAL)
The Splendors LED lighting system allows you to brighten up your spa experience through different multi-colored lights: red, blue, white, purple,
amber, and aqua. You can choose one stationary color or you can cycle through all the colors with the automatic color wheel.
To install Splendors LED lights, simply remove the light reflector by rotating counter-clockwise and pull the factory installed light board out. Install
the new light fixture and reinstall the light reflector by rotating clockwise to complete the installation.
To activate, press the SET button followed by the LIGHT button. To select a specific color, push the LIGHT button (if within 5 seconds) while the
desired color is displayed. If 5 seconds have passed, after color wheel activation, you will need to press SET followed by the LIGHT button to
select a specific color. The Splendors LED lighting option is a great way to personalize your spa experience.
FILTER CYCLES
Your spa will automatically turn the filter cycle on twice each day. When the spa is first powered up the automatic filter cycle will wait 10 minutes
before starting, this is filter cycle 1 and is referred to as F1. Two 1.5 hour filter cycles using the low speed of the jet pump are the programmed
default filter cycle times. The filter cycle occurs twice a day (every 12 hours) the second filter cycle is referred to as F2.
NOTE: The optional FreshWater
®
III ozone system only works when the low speed pump is running.
To modify the length of either filter cycle:
A.
Press and hold the SET button for approximately three seconds.
B.
Press the LIGHT button to select filter cycle 1 or 2 (a 1 or 2 will flash in display).
C. Using the Temp Up (
▲) or the Temp Down (▼) button, adjust the value as desired, from 0 to 6 hours.
D. Programming will then be saved 10 seconds after last button is pressed. The display will then revert back to Temperature display.
The filter cycle will activate the jet pump on low speed for the entire cycle. When activated, the filter cycle Icon on the
display is turned on. If the temperature exceeds the set point by three degrees F for more than three hours, the
system will cancel the FILTER cycle and the filter Icon will blink for the remaining filter cycle time. Should the
temperature cool down to 1.5 degrees F below the set point before the end of the cycle, the cycle will resume for the
rest of the time. Should you use the spa during the filter cycle by placing the jet pump on high speed, the FILTER Icon
will blink. Once the jet pump has been shut off, a ten minute tranquil mode begins (FILTER Icon will be blinking during tranquil mode) before the
filter cycle will resume. The blinking filter Icon indicates that the filter cycle timer is still counting, but the cycle has been temporarily interrupted.
NOTE: The interrupted time of a filter cycle is not extended after the filter cycle resumes. Power interruptions of the spa will reset the filter cycle to
the default 1.5 hour cycle time (F1) and begin 10 minutes after spa regains power.
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
READY
F1
F1
SET
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
SET
READY
F1
F2
SET
F1
F2
SET
SET
READY
READY
F1
F1
F2
F2
READY
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
SET
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
READY
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
READY
F1
SET
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY