Wayne-Dalton 8000 Series Installation Instructions And Owner's Manua - Warning
FOR DOUBLE SPRING
APPLICATIONS:
Repeat
same process for left
hand end bracket.
5/16”
Washer
5/16”
Hex nut
Winding
shaft
5/16” -18 x 3/4”
Carriage bolt
TorqueMaster
®
spring tube
assembly
Right hand
cable drum
5/16” x 1-5/8”
Lag screw
Right
hand end
bracket
Flag
angle
Flag
angle
FOR SINGLE SPRING APPLICATIONS:
Secure the idler bracket to the flag angle using (1)
5/16” - 18 x 3/4” carriage bolt, (1) 5/16” washer and (1) 5/16” - 18 hex nut. Then secure
the idler bracket to the jamb using (1) 5/16” x 1-5/8” lag screw.
TorqueMaster
®
spring tube
assembly
Left hand
cable drum
Idler bracket
Flag
angle
5/16” x 1-5/8”
Lag screw
5/16” -18 x 3/4”
Carriage bolt
5/16” Washer
5/16” Hex
nut
Flag
angle
Left hand
cable drum
Bearing
Attaching Center Bracket to Wall
16
IMPORTANT:
TORQUEMASTER
®
SPRING TUBE MUST BE LEVEL BEFORE SECURING CENTER
BRACKET BUSHING ASSEMBLY TO HEADER.
NOTE:
Drill 3/16” pilot holes into header for the lag screws.
To locate the center bracket bushing assembly, mark the header halfway between the flag
angles and level the TorqueMaster® spring tube. Fasten the center bracket bushing assem-
bly to the header using (2) 5/16” x 1-5/8” lag screws.
TorqueMaster
®
spring tube
Center bracket
bushing assembly
Level
(2) 5/16” x 1-5/8”
Lag screws
Securing Door For Winding Spring(s)
17
With the door in the fully closed position, place locking pliers onto both vertical tracks just
above the third track roller. This is to prevent the garage door from rising while winding
spring(s).
NOTE:
Check the following before attempting to wind spring(s):
a. Counterbalance lift cables are secured at bottom corner brackets.
b. Counterbalance lift cables are routed unobstructed to cable drums.
c. Counterbalance lift cables are correctly installed and wound onto cable lift drums.
d. TorqueMaster
®
spring tube is installed correctly.
e. Review the label attached to the spring warning tag, to determine number of spring turns
required.
NOTE:
Door MUST be closed and locked when winding or making any adjustments to the
spring(s).
WARNING
FAILURE TO PLACE LOCKING PLIERS ONTO VERTICAL TRACK CAN
ALLOW DOOR TO RAISE AND CAUSE SEVERE OR FATAL INJURY.
Locking pliers above
third track roller on
both sides of door
Bottom section
Lock
section
Locking pliers attached
to inner and outer rail
of vertical track
Intermediate section
Vertical
track
Vertical
track
Adjusting Counterbalance Lift Cable
18
Starting on the right side, adjust the cable drum assembly by rotating the drum until the set
screw faces directly away from the header. The position of the cam peak on the TorqueMas-
ter
®
spring tube should be pointing straight up.
Loosen the set screw no more than 1/2 turn. Ensure counterbalance lift cable is aligned and
seated in the first and second grooves of the cable drum. Pull on the end of the cable to
remove all cable slack.
Snug the set screw and then tighten an additional 1-1/2 turns. Measure approximately 6” of
cable and cut off excess cable. Insert end of the cable into the hole of cable drum. Repeat for
left hand cable drum assembly.
IMPORTANT:
ENSURE THE COUNTERBALANCE LIFT CABLE IS SEATED IN THE FIRST
GROOVE OF THE CABLE DRUM PRIOR TO WINDING SPRINGS.
Cam peak
pointing straight up
Insert
cable here
6”
Cut cable here
Tighten
set screw
TorqueMaster
®
spring tube
Counterbalance
lift cable
Insert
cable here
First
groove
NOTE:
Illustration shows the right hand cable drum assembly. Repeat the same process for
the left hand side.
Winding Spring(s)
19
IMPORTANT:
VERIFY THAT THERE ARE NO OBSTRUCTIONS IN THE TRAVEL PATH OF THE
DOOR SECTIONS OR COUNTERBALANCE LIFT CABLES.
IMPORTANT:
INSPECT EACH COUNTERBALANCE LIFT CABLE MAKING SURE IT IS SEATED
PROPERLY ONTO THE CABLE DRUM AND THAT BOTH COUNTERBALANCE LIFT CABLES HAVE
EQUAL TENSION.
PRIOR TO WINDING SPRING(S), CHECK COUNTERBALANCE LIFT CABLES FOR EQUAL
TENSION:
1. Attach locking pliers to track above top roller.
2. Grasp cable at approximate mid-door height location.
3. Draw cable toward you about 1/2” to 1” and release, noting the response of the cable.
4. Repeat above steps for other cable.
5. Adjust cable tension as needed until right and left cables both respond the same.
WARNING
WINDING SPRING IS AN EXTREMELY DANGEROUS PROCEDURE
AND SHOULD BE PERFORMED ONLY BY A TRAINED DOOR SYSTEM
TECHNICIAN USING PROPER TOOLS AND INSTRUCTIONS.
12