Wayne-Dalton TORQUEMASTER 6100 Quick Start Manual - Warning
Using perforated angle (may not be supplied), (2) 5/16” x 1-5/8” hex head lag screws and (3)
5/16” bolts with nuts (may not be supplied), fabricate rear back hangs for the horizontal tracks.
Attach the horizontal tracks to the rear back hangs with 5/16”-18 x 1 hex bolts and nuts (may
not be supplied). Horizontal tracks must be level and parallel with door within 3/4” to 7/8”
maximum of door edge.
NOte:
If an idrive
®
opener is installed, position horizontal tracks one hole above level when
securing it to the rear back hangs.
WarNING
WarNING
keeP HOrIzONtaL trackS ParaLLeL aND WItHIN 3/4” tO 7/8” MaxIMuM
OF DOOr eDGe, OtHerWISe DOOr cOuLD FaLL, reSuLtING IN Severe Or
FataL INJury.
IMPOrtaNt:
DO NOT SUPPORT THE WEIGHT OF THE DOOR ON ANY PART OF THE REAR BACK
HANGS THAT CANTILEVERS 4” OR MORE BEYOND A SOUND FRAMING MEMBER.
NOte:
If rear back hangs are to be installed over drywall, use (2) 5/16” x 2” hex head lag
screws and make sure lag screws engage into solid structural lumber.
NOte:
26” angle must be attached to sound framing members and
nails should not be used
.
Now, permanently attach the weatherstrips on both door jambs and header. The weatherstrips
were temporarily attached in Preparing the Opening, in the pre-installation section of this
manual.
NOte:
When permanently attaching the weatherstrips to the jambs, avoid pushing the weather-
strips too tightly against the face of door.
5/16”-18 x 1-1/4”
Hex bolt must extend into the
track to serve as a roller stop
Perforated angle
Sound framing
members
Horizontal
track
(3) 5/16”
Bolts and nuts
Perforated angle bolted
using (2) 5/16” x 1-5/8”
hex head lag screws to
ceiling member and
parallel to door
Perforated angle
Sound framing
members
Horizontal
track
(3) 5/16”
Bolts and nuts
Perforated angle bolted
using (2) 5/16” x 1-5/8”
hex head lag screws to
ceiling member and
parallel to door
5/16”-18 x 1-1/4”
Hex bolt must extend into the
track to serve as a roller stop
Horizontal tracks
Door edges
3/4” To 7/8”
3/4” To 7/8”
Balancing Door
Tools: Ratchet wrench, Socket: 5/8”, 3” Socket extension, Wrench:
5/8”, (2) Vice clamps, Tape measure, Level, Step Ladder
30
NOte:
Windows will cause the top section to be significantly heavier than the remaining sec-
tions. Wayne-Dalton attempts to balance the door at the top and bottom. To prevent any sudden
door acceleration between the top and bottom, we recommend motor operating all doors with
windows. Doors with windows in the top section should not be manually operated.
Remove any vice clamps. Lift the door and check its balance. Adjust spring(s) if door lifts by itself
(hard to pull down) or if door is difficult to lift (easy to pull down). Anytime spring adjustments are
made, ratchet pawl knob must be in the upper position. An unbalanced door can cause idrive
®
or TorqueMaster
®
Plus operation problems.
Close the door and place vice clamps onto both vertical tracks just above the third track roller.
This is to prevent the garage door from rising while adjusting the counterbalance spring(s).
IMPOrtaNt:
TO ADJUST SPRINGS, ONLY ADD OR REMOVE A MAxIMUM OF 3/10 OF A TURN
(THREE TEETH ON THE RATCHET WHEEL) AT A TIME. BOTH SIDES NEED TO BE ADJUSTED
EQUALLY ON DOUBLE SPRING DOORS.
add spring tension:
The ratchet wheel is made of 10 teeth. To add spring tension, ensure
the ratchet and socket is set so that it will tighten counter clockwise on the right hand side and
clockwise on the left hand side. Place the ratchet wrench with 5/8” socket and 3” socket exten-
sion onto the winding shaft, pull down to add 3/10 of a turn. Watch as three teeth of the ratchet
wheel pass over the pawl, creating three “clicks”.
remove spring tension:
To remove spring tension, place a regular 5/8” wrench onto the
winding shaft. Pull down on the wrench to relieve pressure between the pawl and the ratchet
wheel. Push in on the pawl to allow the three ratchet wheel teeth to pass by the pawl, as you
carefully allow the wrench to be rotated upward by the spring tension, release the pawl to allow
it to engage with the ratchet wheel.
IMPOrtaNt:
BE PREPARED TO HOLD THE FULL TENSION OF THE SPRING.
IMPOrtaNt:
DO NOT ADD OR REMOVE MORE THAN 1 SPRING TURNS (1 SPRING TURN
EQUALS 10 TEETH ON RATCHET WHEEL) FROM THE RECOMMENDED NUMBER OF TURNS
SHOWN ON THE WINDING SPRING TURN CHART.
If the door still does not operate easily, lower the door into the closed position, unwind spring(s)
completely, and recheck the following items:
1.) Check the door for level.
2.) Check the TorqueMaster
®
spring tube and flag angles for level and plumb.
3.) Check the distance between the flag angles, which must be door width plus 3-3/8” to
3-1/2”.
4.) Check the counterbalance lift cables for equal tension, adjust if necessary.
5.) Rewind the spring(s).
6.) Make sure door isn’t rubbing on jambs.
NOte:
If an idrive
®
opener was installed and you have completed this step, refer to the idrive
®
Installation Instructions and Owner’s Manual to complete your idrive
®
installation.
Ratchet
wrench
End bracket
Pawl
Winding
shaft
Ratchet wheel
Pawl knob in
lower position
Pawl knob in
upper position
Pawl
3”
extension
5/8” Socket
9
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com