Summary of N720B
Page 1
User manual wayteq n720b.
Page 2: Notice
Notice using your navigator at the first time 1. Charge completely 2. Install into your vehicle 3. Initialize software as described in the manual 4. Make sure that the car is outside the garage and it is not covered by anything (treed, bridges, etc) 5. Normally it takes a bit longer to receive the g...
Page 3: Contents:
Introduction this manual is a complete instruction for the device. Please ready this manual carefully before using. Contents: safety and regulatory information 1. Getting started 1.1 unpacking 1.2 over view 1.3 using your device in a vehicle 1.3.1 using the car bracket 1.3.2 connecting the car charg...
Page 4
Safety and regulatory information important safety notices and warnings global positioning system the global positioning system (gps) is a satellite-based system that provides location and timing information around the globe. Gps is operated and controlled under the sole responsibility of the govern...
Page 5
1. Getting started 1.1unpacking unpack your device box and identify the contents. You should have: (1) unit. Its main features are a touch-sensitive lcd screen, 1 sd card slot, 1 volume control switch. Details see the photo below. (2) holder，to hold the device. (3) bracket, its main features is to f...
Page 6
(1) charger indicator light (2)saving power switch (3)unit power on/off (4)gps antenna (5)speaker (6)sd card slot: for accessing data as maps. Note: before using gps navigation software and maps, you need to insert the storage card included with your device. Do not remove the card during gps operati...
Page 7
Field of vision is blocked. -- if the car's windshield is tinted with a reflective coating, an external antenna (optional) maybe be needed to route the. Antenna to the top of the car through a window. When closing the car window, be careful not to pinch the antenna cable (cars with an anti-jam windo...
Page 8
The charge indicator glows amber when charging is in progress. Do not disconnect your device from ac power until the battery is fully charged, when the charge indicator turns green. This will take a couple of hours. 1.3.4 assembly to get started, put the device into the holder and assemble holder wi...
Page 9
The suction mount bracket and the device when leaving your vehicle overnight. To remove the bracket, three steps as below: press 2 sides button, pull back lightly and then take off the suction. If the bracket still doesn't detach from your windscreen, tug gently on the clear plastic tab at the edge ...
Page 10
Tap "ok "then enter into the "main function operation screen " as below. Then select the functions you need and then go directly to the way you need. 1.5 power saving press the power button on the top side of your device to turn on and off your device for saving power. When you press the power butto...
Page 11
In addition, there is a close icon on top right corner and a status message on down, the status messages are for pair and connection. When the blue light start flickering, it means the bluetooth has already been opened, but didn’t connect, if the blue light keep bright, then connected. If pnd and bl...
Page 12
3）if ever paired, pnd will connect the device which was paired before automatically when enter into bluetooth interface. And that the mobile phone has ever paired will display: accept connecting xxxx yes or not? Please press “yes”. Then you do not need to enter pin code and searching new device agai...
Page 13
9）if the user has not cancelled the call initiative, but cancelled automatically, it will display “call fail”,that means failed call. 10）if incoming call, it will display “incoming call” and the telephone number. 11）if you accept the incoming call, it will display “active call”. Then you can hear th...
Page 14
Screen.) please use the new pin cod for pair with mobile after setting, otherwise it will not be paired. 17）pair record all mobiles which are paired and connected with device will be shown on this interface. And you can edit them。 when the pnd device connected with one mobile phone, and you want to ...
Page 15
A: pause / play b: stop c: backwards d: forwards e: back to previous screen f: volume control g: back to main menu when you play mp4, you will enter into the full screen display, wherever you tap the screen, will enter into mp4 controller display, touch again, will back to full screen. 2.4 photo 1) ...
Page 16
A: previous b: next c: return to previous menu d: current picture name e: return to main menu f: zoom out g: zoom in h: rotate i: full screen tips: tap full screen button, it will display in full screen size tap previous or next button to view the pictures. If picture is too big or the device does n...
Page 17
A: return to main menu b: previous c: next d: return to previous menu e: current file name f: pages choose g: current page/total pages 2.6 fm transmitter a) tap “system/volume”, go into next interface b) tap the button of “use fm”, turn on fm transmitter, then the button of fm channel adjustment can...
Page 18
1) tap the icon "backlight" and enter into the following display. A. Under backlight icon, tap - to weaken the backlight, tap + to stronger the backlight b. Under battery icon, tap button to select the duration of auto power off the backlight. C. Under ac power icon, tap to select the duration of au...
Page 19
According to the information on the screen, press the right cross centre then take the operation under instruction until the following screen display. 3) language a) tap the icon "language" and enter into the following display. B) tap "" icon to select the language . 4) power tap the icon "power" an...
Page 20
A) tap the icon "volume" and enter into volume setting display. B) tap"-" or "+" to adjust volume of speaker. 6) date and time a) tap the icon "date and time" and enter into the following display. B) tap date icon and use icon to adjust the date. C) tap time icon and use icon to adjust the time. C) ...
Page 21
Operate the device or charge the battery. Do not cover the ac adapter or the car charger with paper or other objects that will reduce cooling. Do not use the ac adapter while it is inside a carrying case. > connect the ac adapter to a proper power source. The voltage requirements are found on the pr...