WeatherMaster A Instruction Manual - page 6
7.1 Timer Mode -
Setting the User Preset Value
7.2 Timer Mode -
Using the Timer
How to Set the User Preset Value
! To select the setting display, hold the [M] button
for 2 seconds, and the flashing "SET" icon will
appear.
! In the setting display, press the [M] button to
change the selection among hour, minute and
second.
! When the digits are flashing (selected), press the
[S/S] or [L/R] button to increase / decrease the
number. (Hold down the button to change the
number at a higher speed).
! When the setting is completed, hold the [M]
button to exit the setting display.
How to Use the Timer
! When the Timer is set, press the [S/S] button to
start the timer. Press the [S/S] button once
again to stop the timer.
Timer Alarm Sound
! In the last 10 minutes, the Watch will beep
for every minute.
! In the last minute, the Watch will beep for
every 10 seconds. In the last 5 seconds,
the Watch will beep for every second.
! When it reaches 0, a beep sound will last for
30 seconds. Pressing any button can stop
the beep sound.
How to Reload the Timer
! The last target time will be reloaded
automatically at the end of the 30-second
beep sound.
! Press the [L/R] button when the timer is
stopped.
! To start a new counting by using a new
target time, set the timer again either by
QSV or UPV.
Increase/ decrease
the number
Increase/decrease
the number at
a higher speed
hold [S/S] / [L/R]
[S/S] / [L/R]
User Preset Value Setting Sequence
Timer Display
Timer Display
(Timer is set at 10 minutes)
Counting Display
Stop Counting Display
Counting Display
digits start
counting
digits stop
counting
digits start
counting
again
[S/S]
[L/R]
hold
[M]
Setting Display
minute
Second
hour
hold
[M]
[M]
[M]
[M]
Real Time
Clock
[S/S]
[S/S]
8.0 Pacer Mode -
Using the Pacer
Pacer Mode
! When the pacer is activated, it will generate beeps at
a pre-defined beeping rate.
! The beeping rate can be set from 30 to 180 beats per
minute (BPM) in an increment of 5.
How to Use the Pacer
!
When
the beeping rate
is
set (for example 30 BPM),
press the
[S/S]
button
to
start the beeping.
! When the watch is beeping, press the
[S/S]
button
to
stop the beeping.
Step Counter
! In supplementary to the Pacer Function, when the
Pacer beeps once, the step counter will advance one.
! When the pacer is activated and the step counter
starts counting, pressing the
[S/S]
button stop
s
the
pacer and step counter.
! The maximum counting limit of the step counter is
99999 steps.
! To reset the step counter to 0, hold the [L/R] button
when the pacer is stopped.
N O T E : W h e n t h e p a c e r h a s b e e n r u n n i n g
continuously for 8 hours, it will stop automatically.
step counter
stop counting
pacer beeping rate
(in beats per minute)
step counter
is counting
8.1 Pacer Mode -
Setting the Pacer value
How to Set the Beeping Rate
! To select the setting display, hold the
[M]
button for 2
seconds in the Pacer Mode.
! When the beeping rate digits start flashing, press the
[S/S] or [L/R] button to increase / decrease the
number. (Hold down the button to change the number
at a higher speed).
! When the setting is completed, press and hold
the [M] button to exit the setting display.
Pacer Mode
30
180
In an increment of
5 BPM
Increase/ decrease
the number
Increase/decrease
the number at
a higher speed
[S/S]
hold [M]
hold [M]
[S/S]/[L/R]
hold [S/S]/ [L/R]
SET
digits have been
selected (flashing)
beep-beep