Web Mountain Technologies TIM-01 User Manual - page 13
TIM-01 User Manual
11 UPB Timer (TIM-01) Version 3
o
Unlike most other screens, this screen will NOT time out after one minute. The only way to take the Timer out of HOST mode is to press
ENTER. The Timer will stay in HOST mode indefinitely, only going back to RUN mode when ENTER is pushed.
•
LOCK MENU (Push FUNCTION button until the following screen shows):
o
The LOCK MENU function allows you to disable the MENU button. If you want to make sure that a casual user does not accidentally, or
maliciously, change any of your settings, program definitions or triggers, you can use this function to keep the MENU button from
functioning at all.
o
From this screen use the UP/DOWN buttons to change the top N to Y if you want to lock the MENU button. Then use the RIGHT button to
advance to the next field and make sure that you use the UP/DOWN buttons to change this N to a Y also. Once both fields are set to N, hit
ENTER. The Timer will return to the RUN screen and the MENU button will be locked. If you try to use the MENU button while it is locked,
you will see the following screen:
o
In order to unlock the MENU button and return it to normal operation, you will need to return to the LOCK MENU screen by successively
pushing the FUNCTION button. This time, make sure both fields are set to N, hit ENTER and the Timer will return to the RUN screen but
now the MENU button will be fully active again.
o
If you push ENTER with the top field set to Y and the bottom field set to N or with the top field set to N and the bottom field set to Y, the
Timer will not change the current locked state of the MENU button. i.e. if the MENU is locked it will stay locked and if it is unlocked it will
stay unlocked.
o
If your timer was set up and installed by a third party and that third party locked the MENU button, you should check with
your installer before using this screen to unlock the MENU button. If you unlock the MENU button and change settings that
cause your system to not operate as designed, your installer may be reluctant to fix the problem gratis.
•
DST 2007/AC SYNCH (Push FUNCTION button until the following screen shows):
o
This screen is strictly informational. It enables you, or your installer, to verify that the Timer is using the 2007 law to calculate Daylight
Saving Time and also that the Timer is synchronizing its time with the national power grid for enhanced clock accuracy.
o
There are no settable fields on this screen.
•
RUN (Push FUNCTION button until RUN shows):
o
This is the normal display which shows current time, date, and day of week. This is the mode that the Timer returns to when you push the
FUNCTION button after being at the ENTER VAC screen.
10
Immediate Run
In addition to the modes that can be reached by successive clicks of the MENU or FUNCTION buttons, there is another handy feature of the Timer:
•
IMMEDIATE RUN option. Whenever the Timer is in RUN mode, hitting the UP button will run P01, hitting RIGHT will run P02, hitting DOWN will
run P03, and hitting LEFT will run P04. The IMMEDIATE RUN buttons are deactivated if the PANIC option for the EMERGENCY mode is
selected, because in that case the UP, RIGHT, DOWN and LEFT buttons operate as PANIC buttons.
•
To make best use of the Immediate Run feature, it is best to define the four programs you want assigned to the four Immediate Run buttons
before you begin setting up timed programs. By setting up programs P01 to P04 first, you reserve them for use by the Immediate Run buttons.
Even if you can’t think of four Immediate Run programs that you want to set up initially, you can reserve P01 through P04 for future use by
setting them up with a start time of NONE (See “Setting Up a Program for Manual Operation Only” in Chapter 7). All other fields can be left as
default values until you are ready to define them with desired actions at a later date. Once you’ve taken this step, all timed programs will be
assigned to P05 or higher.
11
Reset
If the Timer does not seem to be functioning properly, or if you want to change the Daylight Savings Time logic, or you would like to reset the Timer to
it’s original factory settings, you can do so by resetting the Timer. To reset it, disconnect the power plug, wait 5 seconds, then hold the LEFT and
RIGHT buttons down simultaneously, keeping them both depressed as you plug the power cord back into a receptacle. You should see the following
screen: