Summary of RANCH KETTLE 39950
Page 1
Ranch ® kettle 44 3 ⁄ 4 inch (114 cm) 39950
Page 2
2 warning: do not use gasoline, alcohol, or other highly volatile fluids to ignite charcoal. Use a commercially prepared firestarter and make sure that, if using lighter fluid, any fluid that may have drained through the bottom vents is removed before lighting the charcoal. Warning: never use kettle...
Page 3
3 top frame assembly bottom frame assembly lid assembly bowl assembly ash catcher hinged cooking grate charcoal grate tuck-away frame support axle frame handle wire lid holder assembly tuck-away support bracket two lid tabs parts.
Page 4
4 four aluminum tubing plugs two wheels two wheel hubcaps five 1/4-20 hex nuts (actual size) ten nylon washers (actual size) five 1/4-20 x 1 3/4 inch bolts (actual size) six 5/16 inch steel washers (actual size) six 5/16-18 x 7/8 inch bolts (actual size) eight 5/16-18 hex nuts (actual size) eight 5/...
Page 5
5 (1) (2) (3) (1) (3) assemble frame you will need: top frame assembly (1) , bottom frame assembly (2) , 7/16 inch open-end or an adjustable wrench and pliers. Remove hex nut and bottom washer (3) from the bolt that is preinstalled in the top frame assembly. Do not remove top bolt and washer from to...
Page 6
6 (1) continue frame assembly you will need: frame assembly, two wheels, two hubcaps, axle, tuck-away frame support, hammer, a block of wood, pliers and a 7/16 inch open-end or an adjustable wrench. Place one end of axle on block of wood (or other protected surface). Tap on one hubcap. Put one wheel...
Page 7
7 (1) (2) (3) assemble frame handle you will need: frame assembly, frame handle, four 1/4-20 x 1 3/4 inch bolts, eight nylon washers, four 1/4-20 hex nuts, 7/16 inch open-end or an adjustable wrench and pliers. Hold frame handle (1) between caster legs. Place a washer (2) on bolt (3) , insert throug...
Page 8
8 install bowl assembly you will need: bowl assembly, four 5/16-18 x 7/8 inch bolts, four 5/16 inch steel washers, four 7/8 inch aluminum washers, four 5/16-18 hex nuts, four 5/16 inch lock washers, 1/2 inch open-end or an adjustable wrench and pliers. Set bowl in frame. Place a steel washer (1) on ...
Page 9
9 (4) (5) (1) (2) (3) install wire lid holder assembly you will need: wire lid holder assembly and a 1/2 inch open-end or an adjustable wrench. Remove 5/16-18 hex nut (1) , 5/16 inch lock washer (2) and 7/8 inch aluminum washer (3) from each end of wire lid holder. Finger tighten remaining 5/16-18 h...
Page 10
10 install tuck-away support bracket you will need: tuck-away support bracket, plastic tubing plug, 1/4-20 x 1 3/4 inch bolt, two nylon washers, 1/4-20 hex nut, 7/16 inch open-end or an adjustable wrench and pliers. Insert tabs of support bracket through slot in tuck-away frame support (a) . Place a...
Page 11
11 (1) final assembly you will need: charcoal grate, hinged cooking grate, three tool holders and lid assembly. Set charcoal grate, then cooking grate in bowl. Add lid. Hook tool holders (1) over frame handle. Weber-stephen products co., (weber) hereby warrants to the original purchaser of this webe...
Page 12
12 1 2 3 4 5 13 14 15 16 18 19 21 22 16 26 27 15 20 21 33 6 7 8 9 10 11 12 23 24 28 13 16 29 25 30 19 31 20 32 34 35 36 37 38 13 17 4 5 7 20 13 25 12 15 20 19 printed in u.S.A. 39950 4/11/05 parts list all items are single quantities unless otherwise specified. Parts can be ordered from weber-stephe...