User's manual questions? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, please call: or write: icon health & fitness ltd. Unit 4 revie road industrial estate revie road beeston leeds, ls11 8jg uk ema...
2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
3 before you begin assembled dimensions: height: 196 cm (77 in.) width: 99 cm (39 in.) length: 122 cm (48 in.) foot plate low pulley station high pulley station lat bar leg lever arms weight stack backrest weight pin thank you for selecting the versatile weider ® 8507 training system. The weider ® 8...
4 assembly assembly requires two people. Due to the size and weight of the training system, assemble it in the location where it will be used. • place all parts of the training system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is comple...
5 3. Slide six weights (25) onto the weight guides (72). Be sure that all of the weights are turned so the pin grooves are on the indicated side. 4. Press the 1 1/4” square inner cap (57) into the front upright (42). Attach the 1” plastic stop (64) to the centre hole in the stop bracket (63) with a ...
6 5. Press the weight tube bumper (79) into the end of the weight tube (80). Slide the top weight (77) onto the weight tube. Be sure that the pins on the weight tube are resting in the pin grooves under the top weight. Locate the short cable (23). Attach the short cable to the weight tube (80) with ...
7 8. Attach the upper ends of the weight guides (72) to the top frame (67) with the 5/16” x 6” bolt (74), two 1/2” x 3/4” spacers (73), and a 5/16” nylon locknut (3). Tighten all nylon locknuts used in steps 4 through 8. 9. Press two 1 3/4” square inner caps (44), two 1 1/2” square inner caps (32), ...
8 11. Press a 1 3/4” square inner cap (44) into each end of an arm (46). Apply lubricant to the lower axles on the arm frame (52). Slide an arm (46) onto one of the axles. Hold two 1” retainers (54) and a 1” round cover cap (55) against the lower end of the axle. The teeth on the retainers must bend...
9 14. Attach a large “u” bracket (56) to one of the arms (46) with a 3/8” x 2 3/4” bolt (70), 3/8” washer (9), and 3/8” nylon locknut (21). Be sure that the swivel bracket (58) is on the inside as shown. Do not overtighten the 3/8” nylon locknut. Attach a large “u” bracket (56) to the other arm (46)...
10 16. Remove the 3/8” x 1 3/4” bolt (48), 3/8” nylon jam nut (5), and 3 1/2” pulley (15) from the indicated bracket on the top frame (67). Insert the end of the long cable (66) through the bracket and down through the indicated hole. Re-attach the 3 1/2” pulley (15) to the bracket on the top frame ...
11 19. Note: the 4 1/2” pulley (81) shown in this step is pre-attached to the adjustment “u” bracket (75). Remove the 3/8” x 1 3/4” bolt (48), 3/8” nylon lock nut (21), and the 4 1/2” pulley (81) from the adjustment “u” bracket (75). Attach the adjustment “u” bracket (75) to the front upright (42) w...
12 21. Attach the 5/16” x 3” bolt (17), two 5/16” washers (8), and a 5/16” nylon jam nut (2) to the indicated hole in the top frame (67). Slide the end of the long cable (66) onto the 5/16” x 3” bolt (17). Tighten another 5/16” nylon jam nut (2) onto the bolt. Note: the 5/16” nylon jam nut should no...
13 23. Attach the 5/16” x 3 1/2” bolt (87), two 5/16” washers (8), the 1” metal spacer (22), and a 5/16” nylon locknut (3) to the front upright as shown. Wrap the short cable (23) around a 3 1/2” pulley (15). Attach the pulley to the front upright (42) with a 3/8” x 3 1/2” bolt (16), a 3/8” washer (...
14 26. Press a 1 1/2” square inner cap (32) into the leg lever (29). Attach the 5/16” x 2” eyebolt (62) to the leg lever (29) with a 5/16” washer (8) and a 5/16” nylon locknut (3). Lubricate a 5/16” x 2 1/4” bolt (33). Attach the leg lever (29) to the seat frame (36) with the bolt and a 5/16” nylon ...
15 29. Slide a handgrip (12) onto each end of the lat bar (85). 29 85 12 12 30. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in adjust- ment, beginning on page 16 of this manual. Before using the training system, pull each cable a few times to mak...
16 adjustment the instructions below describe how each part of the training system can be adjusted. Important: when attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cable or chain ...
17 attaching and removing the seat set the bracket on the seat frame (36) on the indicated pin on the front upright (42). Attach the seat frame to the front upright with the 5/16” x 2 3/4” carriage bolt (14) and seat knob (40). For some exercises, the seat (13) must be removed. First, make sure that...
18 attaching the lat bar or nylon strap to the low pulley station attach the lat bar (85) to the short cable (23) with a cable clip (83). For some exercises, the chain (84) should be attached between the lat bar and the short cable with two cable clips. Adjust the length of the chain between the lat...
19 trouble-shooting and maintenance inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. The training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cabl...
20 cable diagrams the cable diagrams below show the proper routing of the short cable (23) and the long cable (66). Use the diagrams to make sure that the two cables are assembled correctly. The numbers show the routing of each cable. Short cable (23) long cable (66) weight stack—1 low pulley—3 2 hi...
21 notes.
22 key no. Qty. Description 1 4 5/16” x 2 1/2” carriage bolt 2 2 5/16” nylon jam nut 3 21 5/16” nylon locknut 4 1 base 5 7 3/8” nylon jam nut 6 1 support plate 7 1 1/4” nylon locknut 8 16 5/16” washer 9 5 3/8” washer 10 4 1/4” washer 11 5 5/16” x 2 3/4” bolt 12 4 handgrip 13 1 seat 14 1 5/16” x 2 3/...
23 39 56 21 59 15 5 15 15 78 78 5 48 58 88 71 4 19 1 27 34 34 32 34 29 3 33 7 30 10 28 34 32 36 13 40 14 23 87 8 22 16 15 3 3 8 3 5 9 26 88 42 41 10 43 25 79 80 85 84 83 45 44 8 33 49 51 47 8 3 54 55 46 9 70 55 54 3 8 49 47 33 45 44 51 9 70 46 44 53 53 44 44 89 52 60 89 57 8 3 3 11 8 3 64 24 63 3 72...
5/16" nylon locknut (3) 1/4" washer (10) 5/16" washer (8) 3/8" washer (9) 5/16" nylon jam nut (2) 1/4" nylon locknut (7) 3/8" nylon locknut (21) 1/4" nylon jam nut (86) 3/8" nylon jam nut (5) 1/4" x 1/2" screw (31) 1/4" x 3/4" screw (18) 1/4" x 2 1/2" screw (43) 5/16" x 1 1/2" bolt (24) 3/8" x 1 3/4...
1/2" x 3/8" spacer (51) 1" retainer (54) 1" plastic stop (64) 1/2" x 1/2" spacer (65) 1/2" x 3/4" spacer (73) 1" metal spacer (22) 5/16" x 2 1/2" carriage bolt (1) 5/16" x 2 3/4" carriage bolt (14) 5/16" x 2 3/4" bolt (11) 3/8" x 2 3/4" bolt (70) 5/16" x 3" bolt (17) 5/16" x 3 1/4" bolt (35) 5/16" x...
1" round cover cap (55) 5/16" x 2" eyebolt (62) 1 1/4" square inner cap (57) 1 1/2" square inner cap (32) 1 3/4" square inner cap (44) 2" square inner cap (27) 2" square outer cap (88) 1" round inner cap (49) 3/4" round inner cap (34).
Ordering replacement parts to order replacement parts, contact the icon fitness lifestyle ltd. Office, or write: unit 4 revie road industrial estate revie road beeston leeds, ls118jg uk tel: country code: outside the uk: 0 (044) 113 387 7133 fax: 0 (044) 113 387 7125 please provide the following inf...
