User's manual questions? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory. To avoid delays, please call direct to our toll- free customer ...
2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Important precautions 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in the literature. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately inform...
4 before you begin assembled dimensions: height: 76.0 in. Width: 86.5 in. Length: 91.5 in. Foot plate low pulley station high pulley station lat bar leg lever butterfly arms press arms leg press seat seat weight stack backrests curl pad ab pulley station warning decal warning decal thank you for sel...
5 assembly make sure you have the following tools: • two (2) adjustable wrenches • one (1) standard screwdriver • one (1) phillips screwdriver • one (1) rubber mallet • you will also need grease or petroleum jelly, a small amount of soapy water, and clear tape or masking tape. Note: assembly will be...
1. Locate and open the parts bags labeled “frame assembly.” see the inset drawing. Insert two 1 1/2” x 2 1/2” inner caps (83) and two 3/8” x 2” carriage bolts (92) into the butterfly base (4). Insert two 1 1/2” x 2 1/2” inner caps (83) into the indicated ends of the butterfly base (4) and the press ...
5. Attach the butterfly seat frame (14) to the butterfly upright (1) with two 3/8” x 3 1/4” bolts (62), two 3/8” flat washers (48), and two 3/8” nylon locknuts (50). Attach the butterfly seat frame (14) to the butterfly front leg (3) with two 3/8” x 3 1/4” bolts (62), two 3/8” flat washers (48) and ...
8 89 48 48 48 89 51 6 50 48 21 slot 15 9. See the inset drawing. Insert two weight inserts (56) into each weight (21). Set the two weight bumpers (51) over the holes in the corner bar of the press base (6). Slide the weight guides (15) through the weight bumpers (51) and the holes in the press base ...
9 48 62 50 48 33 9 12. Secure the press top frame (9) to the butterfly top frame (33) with two 3/8” x 3 1/4” bolts (62), two 3/8” flat washers (48), and two 3/8” nylon locknuts (50). Do not tighten the nylon locknuts yet. 13. Secure the weight guides (15) to the press top frame (9) with two 3/8” x 1...
10 15 48 48 10 84 28 10 28 48 48 53 53 15. Insert a 2” square inner cap (28) into the end of the butterfly arm (10). Attach a butterfly handle (53) to the butterfly arm (10) with two 3/8” x 1” bolts (84) and two 3/8” flat washers (48). Repeat this step with the other butterfly arm (10). 16. Lubricat...
21. Locate and open the parts bags labeled “cable assembly” and “pulleys.” locate the butterfly cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the butterfly cable (73) to the right pivot arm (85) with a 5/16” x 2 1/4” shoulder bolt (79) and a 5/16” nylon jam...
12 23. Remove the preassembled 3/8” x 2” bolts (54) from one set of adjustable pulley plates (23). Wrap the butterfly cable (73) around a 3 1/2” pulley (24). Attach the 3 1/2” pulley and a cable trap (25) between the top holes of the adjustable pulley plates (23) with a 3/8” x 2” bolt (54) and a 3/8...
13 27. Wrap the ab cable (47) around a 3 1/2” pulley (24). Insert the ab cable down through the press top frame (9). Attach a 3/8” flat washer (48) and a 5/8” x 3/4” bushing (66) to a 3/8” x 3 1/4” bolt (62). Slide the bolt through the press top frame and the 3 1/2” pulley. Secure another 5/8” x 3/4...
14 31. Locate the weight cable (72). Note that one end of the weight cable has a bolt, and the other end has a ball on it. Lay the weight cable (72) inside the bracket on the butterfly base (4) in the manner shown. Attach a 3 1/2” pulley (24) to the bracket with a 3/8” x 2” bolt (54) and a 3/8” nylo...
15 36 37 38 35. Wrap the weight cable (72) around a 3 1/2” pulley (24). Attach the 3 1/2” pulley and a cable trap (25) to the butterfly upright (1) with a 3/8” x 4” bolt (59), a 3/8” flat washer (48), and a 3/8” nylon jamnut (63). Be sure that the cable trap is turned to hold the cable in place. 36....
16 39. Wrap the weight cable (72) around a 3 1/2” pulley (24). Attach the 3 1/2” pulley and a cable trap (25) between the lowest holes in the adjustable pulley plates (23) hanging from the ab cable (47) with a 3/8” x 2” bolt (54) and a 3/8” nylon locknut (50) that was removed in step 28. Be sure tha...
17 43. Locate the leg press cable (75). Attach the leg press cable to the indicated side of the press upright (2) with a 3/8” x 3 1/4” bolt (62) and a 3/8” nylon locknut (50). Do not tighten the nylon locknut yet. Wrap the leg press cable (75) up around a 3 1/2” pulley (24) in the direction shown. A...
18 47. Remove the 3/8” nylon locknut (50) from the indi- cated 3/8” x 5 1/2” bolt (55). Wrap the leg press cable (75) around a 3 1/2” pulley (24). Secure the 3 1/2” pulley and a cable trap (25) to the 3/8” x 5 1/2” bolt (55) on the indi- cated side of the press base (6) with the 3/8” nylon locknut (...
19 51. Locate and open the parts bag labeled “seat assembly.” attach a seat (13) to the brackets on the butterfly seat frame (14) using four 1/4” x 3/4” bolts (49). Repeat this step with the other seat (not shown) and the press seat frame (not shown). 52. Press a 1 1/2” square inner cap (35) into th...
20 55 56 91 46 3 39 55. Press two 3/4” round inner caps (43) into each of the two pad tubes (42). Slide a foam pad (30) onto one side of a pad tube (42). Slide the pad tube through the hole in the leg lever (41). Slide another foam pad onto the other side of the pad tube. Slide a foam pad (30) onto ...
21 adjustments the instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. Impor- tant: when attaching the lat bar, ab strap, or nylon strap, make sure that t...
22 attaching the ab strap to the ab pulley station attach the ab strap (81) to the ab cable (47) at the ab pulley station with a cable clip (69). Adjusting the backrest to adjust a backrest (12), loosen the adjustment knob (5) on the press upright (2) or the butterfly upright (not shown) by turning ...
23 weight resistance chart this chart shows the approximate weight resistance at each weight station. “top” refers to the 10 lb. Top weight. The other numbers refer to the 10 lb. Weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. Note: the actual resistance ...
Troubleshooting inspect and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the cables woven cable, the type of cable used on the weight sys...
25 cable diagrams the cable diagrams on this page and the next page show the proper routing of the leg press cable (75), the ab cable (47), the butterfly cable (73), and the weight cable (72). Use the diagrams to be sure that the cables have been assembled correctly. The starting and ending points o...
26 weight cable (72) 2 3 1—low pulley 4 8 11 12—weight stack 7 6 5 cable id 72 47 75 73 9 10
27 notes.
2" x 3” inner cap (78) 2" square inner cap (28) 1 1/2" square inner cap (35) 1 1/2" x 2 1/2” inner cap (83) 2 1/2" square inner cap (76).
5/16" nylon jamnut (34) cable clip (69) "v" pulley (27) (not shown to scale) 3 1/2" pulley (24) (not shown to scale) retainer ring (31) 4 1/2" pulley (82) (not shown to scale) 1/2" flat washer (11) 1/2" plain nut (45) 1/2" nylon jamnut (36) 5/16" nylon locknut (64) 3/8" nylon jamnut (63) 3/8" nylon ...
5/16" x 2 1/4" shoulder bolt (79) 3/8" x 1" bolt (84) 3/8" x 1 3/4" bolt (57) 3/8" x 1 1/2" button head bolt (98) 1/4" x 3/4" bolt (49) 3/8" x 4" bolt (59) 1/2" x 4" bolt (68) 3/8" x 4 3/4" bolt (60) 3/8" x 2 1/2" bolt (87) 3/8" x 2 3/4" bolt (89) 3/8" x 3" bolt (88) 3/8" x 3 1/4" bolt (62) 5/16" x ...
Part list—model no. Wesy37531 r1003a note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key no. Qty. Description key no. Qty. Description 1 1 butterfly upright 2 1 press upright 3 1 butterfly front leg 4 1 butterfly base 5 2 adjustment knob 6 1 press bas...
92 92 49 39 49 23 25 24 25 24 23 50 54 23 25 24 25 24 23 50 44 35 49 86 65 77 28 65 86 77 64 25 24 60 96 68 36 25 24 50 8 68 29 36 68 36 63 25 24 25 24 60 90 78 62 48 50 80 40 20 50 83 6 60 24 25 50 50 49 50 24 25 50 7 50 50 25 24 50 25 24 55 50 50 48 62 5 47 66 66 50 48 48 62 2 47 13 50 75 62 75 83...
Ordering replacement parts to order replacement parts, simply call our customer service department toll-free at 1-800-999-3756, monday through friday, 6 a.M. Until 6 p.M. Mountain time (excluding holidays). To help us assist you, please be pre- pared to give the following information: • the model nu...