Wood Pellet WPGGE1.5L Owner's Manual - page 6
10
Avecos (Sq Black
Washers)
•
PyroCeram Windows to Oven and Firebox Doors
–
5 each
3
Spring Handles
•
Oven Door Latch, Firebox Door Latch, and Damper Dial
–
1 each
8
#12 Screws
•
Grill Rails to Inside of oven
–
2 each
1.2 Assembly Instructions
Step 1 - Installing the Hopper:
Place mount the hopper brackets on the left side of the grill using
two 10/32” bolts each. The long side of the bracket should face outwards. Slide the hopper chute
into
slot on left side of heater down through air chute inside of heater. Hopper will set into the first grooves
on the hopper brackets. There are four holes near the hopper chute where you will screw in four
10/32” bolts. Slide the aluminum heat shield in
-between the hopper and the firebox, sitting into the
second set of grooves on the hopper brackets.
Step 2 - Installing the Hopper Lid:
Attach Hopper lid usi
ng two 10/32”
bolts and
10/32” nylon
lock
nuts. Do
not tighten past the threads on the lock nuts to allow for enough room so the lid can hinge
properly and close completely.
Step 3 -
Attaching Hopper Handle:
place two 1/4 x 7/8”
bolts through the handle holes. Align with
the holes on the hopper and fasten with one 1/4" lock washers and one 1/4" nut each.
Step 4 - Assembling the Ashpan:
place two 1/4 x 7/8”
bolts through the handle holes. Align with
the holes on the ashpan front and ashpan. Ashpan Front should have the side with a shorter distance
from the holes towards the top. fasten with one 1/4" lock washer and one 1/4" nut each.
Step 5 - Installing the grill rails:
L brackets should face downward.
Using two #12 metal screws per
rail. Align over holes and tighten.
Step 6 - Attach Right Side Handle
: Place 1/4" lock washer on two 1/4 x 7/8” bolts and place into
handle holes. Fasten to the holes located towards the top of the right side of the grill.
Step 7 - Install Deluxe Firepot:
Insert the Deluxe Firepot into the square cutout on the firebox
bottom. The 3/8” nut on the bottom of the fire pot will face towards the hopper. Make sure the fire pot
sits flush with bottom. Place large washer onto the pull rod. Insert the Pull rod from hopper side and
align with nut on firepot bottom. Turn clockwise until tight. Test and pull rod ensuring there is nothing
objecting its clean pulling swipe. The pull rod should be pushed in during operation.
Step 8 - Install Firebox and Oven Doors with Hinges:
attach firebox hinge and oven hinge with 2
10/32” bolts each. The Threaded side of the hinges go on top.
Using two 1/4"
x 1/2’’ bolts
, secure
each door to their respective door hinges. Do not tighten all the way leaving room for the door to open
and close with ease.
Step 9 - Installing Glass:
Insert 5 10/32” bolts to the perimeter holes of the firebox and oven doors
.
Place glass between mounting bolts and fasten with one Aveco (Sq. black washer) for each bolt.
Make sure to keep pressure against glass until all five Avecos are in place. For a snug fit, Hold the
Avecos in place while tightening the 10/32 bolts (caution: too much pressure can crack the glass).
Step 10 - Installing Spring Handles:
twist spring handles clockwise on to the two door latches and
the damper dial.