1. DL manuals
  2. Worx
  3. Chainsaw
  4. WG305E
  5. Safety And Operating Manual Original Instructions

Worx WG305E Safety And Operating Manual Original Instructions

Summary of WG305E

  • Page 1

    Safety and operating manual original instructions chain saw wg305e.

  • Page 3: Chain Saw

    Chain saw wg305e 3 general power tool safety warnings warning: read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in th...

  • Page 4: Chain Saw

    Chain saw wg305e 4 g) if devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) power tool use and care a) do not force the power tool. Use the correct power tool f...

  • Page 5: Chain Saw

    Chain saw wg305e 5 operator and/or throw the chain saw out of control. 8. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance. 9. Carry the chain saw by the front handle with the chain saw switched off an...

  • Page 6: Chain Saw

    Chain saw wg305e 6 cleared as necessary before cuts are started. The escape path should extend back and diagonally to the rear of the expected line of fall as illustrated in figure 1. Before felling is started, consider the natural lean of the tree, the location of larger branches and the wind direc...

  • Page 7: Symbols

    When the log is supported on one end, as illustrated in figure 4, cut 1/3 the diameter from the underside (underbuck) (1). Then make the finished cut by overbucking (2) to meet the first cut. When the log is supported on both ends, as illustrated in figure 5, cut 1/3 the diameter from the top (overb...

  • Page 8

    3 4 1 12 1 14 2 21 2 1 1 13 17 18 20 19 11 6 7 10 9 8 5 23 1 15 16.

  • Page 9: Chain Saw

    Chain saw wg305e 9 1. Rear handle 2. On/off switch/trigger 3. Lock-out button 4. Oil level window 5. Oil filler cap 6. Front handle 7. Activation lever for kickback brake (hand guard) 8. Bumper spike 9. Guide bar 10. Chain 11. Chain tensioning knob 12. Chain cover 13. Extension cord holder 14. Rear ...

  • Page 10: Chain Saw

    Chain saw wg305e 10 technical data type wg305e (3- designation of machinery, representative of chain saw ) voltage 230-240v~ 50hz power 1100w bar length 25cm chain speed 8.5m/s oil tank capacity 120ml chain pitch 3/8” number of chain drive links 40 chain gauge 0.050’’ saw chain type es91vs bar type ...

  • Page 11: Chain Saw

    Chain saw wg305e 11 and the tool is being used as intended by its design and these instructions. This tool may cause hand-arm vibration syndrome if its use is not adequately managed warning: to be accurate, an estimation of exposure level in the actual conditions of use should also take account of a...

  • Page 12: Chain Saw

    Chain saw wg305e 12 operation instruction note: before using your tool be sure to read the instruction manual carefully. Intended use the chain saw is intended for sawing of trees, tree trunks, branches, wooden beams, planks, etc. Cuts can be sawed with or across the grain. This product is not suita...

  • Page 13: Chain Saw

    Chain saw wg305e 13 note: chain should rotate freely and be free of kinks. 7. Fit the chain cover (12) and tighten the chain cover by turning the chain tensioning knob (11) clockwise until it is tight. (see fig. D) warning: the chain is not yet tensioned. Tensioning the chain applies as described un...

  • Page 14: Chain Saw

    Chain saw wg305e 14 note: the chain (10) will stretch while cutting and lose proper tension. When the chain becomes loose, completely unscrew the chain tensioning knob (11) or turn the knob around three full turns in a counter- clockwise direction, then retighten the chain tensioning knob (11) to pr...

  • Page 15: Chain Saw

    Chain saw wg305e 15 operation 1. Switching on and off (see fig. G) attention: check the voltage and current supply: the voltage and current supply must comply with the ratings on the product plate. For switching on the tool, press the lock-out button (3), then fully press the on/off switch (2) and h...

  • Page 16: Chain Saw

    Chain saw wg305e 16 against the wood. The wood should be as close to the sawbody as possible. Hold saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw. (7) guide the saw using light pressure and do not put excessive force on the saw, letting the saw do its work, or t...

  • Page 17: Chain Saw

    Chain saw wg305e 17 3. The chain (10) must be running at full speed before it makes contact with the wood. 4. Use the bumper spikes (8) to secure the saw onto the wood before starting to cut. 5. Use the bumper spikes as a leverage point while cutting. (see fig. K) 6. Do not operate the chain saw wit...

  • Page 18: Chain Saw

    Chain saw wg305e 18 saw closely if guard or other part has been damaged. Check for any damage that may affect operator safety or operation of saw. Check for alignment or binding of moving parts. Check for broken or damaged parts. Do not use chain saw if damage affects safety or operation. Have damag...

  • Page 19: Chain Saw

    Chain saw wg305e 19 check the condition of the guide bar each time the chain is sharpened. A worn guide bar will damage the chain and make cutting difficult. After each use, with unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole. When rail top is uneven, use...

  • Page 20: Chain Saw

    Chain saw wg305e 20 injecting grease to lubricate a z y kg z y l m n o p lubricating the guide bar sprocket 1. Clean the bar and sprocket 2. Using a grease gun, insert the tip of the gun into the lubrication hole and inject grease until it appears at the outside edge of the sprocket tip. (see fig. P...

  • Page 21: Chain Saw

    Chain saw wg305e 21 troubleshooting warning: switch off and remove plug from power source before investigating fault. Symptom possible cause chain saw fails to operate kickback brake is activated no power power source socket faulty extension cord damaged pull hand guard back in position (figure h) c...

  • Page 22: Chain Saw

    Chain saw wg305e 22 plug replacement (uk & ireland only) if you need to replace the fitted plug then follow the instructions below. Important the wires in the mains lead are colored in accordance with the following code: blue – neutral brown – live as the colors of the wires in the mains lead of thi...

  • Page 24

    Copyright © 2016, positec. All rights reserved. Ar01270701 www.Worx.Com.