Summary of 770F
Page 1
User’s manual for 770f elliptical built for health.
Page 2
4* m8*55l m8 1* assembly step# 1 1) attach the front stabilizer (d-1) to the main base using hex screw (h-1). 2) attach the rear stabilizer (e-1) to the mid-frame extrusions of the main base using carriage screw (h-2), flat washers (h-3), and nuts (h-4) as shown above..
Page 3
M8xp1.0x20l φ8xφ25x2t assembly step # 2 1) assemble the left padel arm (f-7) to the main frame with nylok screw (f-9), flat washer (f-10) and cover for connector bracket (f-28). 2) assemble the right padel arm (f-8) to the main frame with nylok screw (f-9), flat washer (f-10) and cover for connector...
Page 4
Assembly step # 3 1) remove the preinstalled mounting hardware from the main base. 2) connect the upper cable wire (c-2) to the lower cable wire (g-2). 3) slide the handlebar post (c-1) down onto the base assembly. Align the mounting holes and thread the 3 in 1 bolt (c-3) in place as shown. 4) inser...
Page 5
Assembly step # 4 1) assemble the right and left pedal (f-1/f-2) to the corresponding pivot collars referencing the orientation shown in the drawing. Hardware used per side: linkage arm (f-4), flat washer (f-5), screw (f-6). 2) align the screw mounting patterns of left and right foot pedal (f-26/f-2...
Page 6
Assembly step # 5 1) attach both upper handlebar (i-1/i-2) to the corresponding lower handlebars using carriage screw (h-15), curve washer (h-16) and nut (h-5) per side. M8x40l 8* 19*2t m8 4* 1*.
Page 7
Assembly step # 6 1) carefully routes the pulse cable coming through the middle of the handlebar post (c-1). 2) secure the front handlebar (b-1) to the handlebar post (c-1) using a combination of round hex screw (h-13), spring screw (h-12) and flat washer (h-11). Once the u handle is secured to the ...
Page 8
Assembly stage # 7 1) connect the pulse cable and upper cable wireinto the board mounted connector on the back of the computer. 2) tuck the excess cable length into the mounting bracket and attach the computer to the mounting bracket using screw (a-2). 3) plug in the cord end of the adaptor (g-26) i...
Page 9
Assembly drawing.
Page 10
Assembly parts in the carton.
Page 11
Explored drawing.
Page 12
Part list no description q'ty a computer assembly 1 set a-1 computer 1 pcs a-2 screw 4 pcs b handlebar assembly 1 set b-1 front handlebar 1 pcs b-2 hand pulse 2 pcs b-3 end cap 2 pcs b-4 grip for handlebar 2 pcs b-5 pulse cable 1 pcs b-6 cap for wire 1 pcs c handlebar post assembly 1 set c-1 handleb...
Page 13
No description q'ty f-6 screw 6 pcs f-7 left padel arm 1 pcs f-8 right padel arm 1 pcs f-9 nylok screw 2 pcs f-10 flat washer 2 pcs f-11 shaft busing of handlebar 4 pcs f-12 connector bracket of pedal tube 2 pcs f-13 screw 2 pcs f-14 flat washer 4 pcs f-15 nut 2 pcs f-16 wave washer 2 pcs f-17 metal...
Page 14
No description q'ty g-15 texture nut 2 pcs g-16 self-tapping screw 7 pcs g-17 screw 8 pcs g-18 connecter for roller arm 1 pcs g-19 sensor box 1 pcs g-20 screw 1 pcs g-21 alex 1 pcs g-22 screw 3 pcs g-23 pulley 1 pcs g-24 bushing 1 pcs g-25 dc wire 1 pcs g-26 adaptor 1 pcs h screw kit 1 set h-1 screw...
Page 15
No description q'ty i-3 lower handlebar left 1 pcs i-4 lower handlebar right 1 pcs i-5 foam grip 2 pcs i-6 end cap 2 pcs i-7 metal bushing 4 pcs j magnetic assembly 1 set j-1 magnetic 1 pcs j-2 screw 1 pcs j-3 spring screw 2 pcs j-4 screw 2 pcs j-5 flat washer 2 pcs j-6 bushing' 1 pcs j-7 nut 1 pcs ...
Page 16: Instruction Manual Of
Instruction manual of sm27 49 -67 button function: mode in stop mode, the mode is to confirm all exercise data setting, and enter into program. Reset in stop mode, press the button back to main menu. Start/stop to start or stop exercise. Recovery to test heart rate recovery status. Up to select trai...
Page 17
Note: 1. This computer require 9v , 0.5ma adaptor. 2. When user stop pedaling for 4 minutes, computer will enter into power save mode, all setting and exercise data will stored until user start exercise again. 3. When computer act abnormal, please plug out the adaptor and plug in again..
Page 18
Important information regarding service in you have any problems, please contact mylna service. Our consultants have extensive experience and will help you with questions about products, installation, ordering spare parts or any errors and omissions. We would like you to contact us before contacting...