- DL manuals
- X-TREME
- Scooter
- X-250
- User Manual
X-TREME X-250 User Manual
Summary of X-250
Page 1
Page1 x-250 electric scooter user manual (photos may vary) please be safe when riding always wear a helmet and obey all laws! X-treme tm electric scooters.
Page 2: Battery Maintenance and
Page2 battery maintenance and charging instructions 1. You must charge completely prior to initial use. (follow charging instructions in your product handbook) 2. Charge immediately after each use. 3. Charge before storage. You must charge every 30 days if not in use. 4. Charge the unit for 6-8 hour...
Page 3: Important
Page3 warning this product does not conform to federal motor vehicle standards and is not intended for operation on public streets, roads or highways. Serious injury can result from the unsafe operations of this product. Operator can minimize these risks by using certain safety equipment such as: sa...
Page 4
Page4 safety guide the recommended age for riding this scooter is 14 years old or older. To avoid damage to the motor and footplate, do not overload the scooter. Never ride with more than one person. Inspect your scooter thoroughly before each use for loose or missing parts. Avoid unintentional star...
Page 5
Page5 do not return to store! Do not use this vehicle for the first time until you have inflated the tires to the correct psi and completely charged the battery. Failure to follow these instructions may damage your vehicle and void your warranty. Please call or go online 1-253-777-0690 www.X-tremesc...
Page 6
Page6 table of contents important information…………………………………….…………………………………………… 2 quick reference………………………………………………………………………………………….. 4 table of contents……………………………….…………….………………………………………… 6-7 getting to know your x-treme x- 250……………….…………………………………………….. 8 package contents & getting started.. …………….……...
Page 7
Page7 troubleshooting……………………………………………………………………………………… 22-25 no power………………………………………………………………………………………………… 22 after fully charging, powers only for short distance use………………………………………..22-23 scooter takes off, will not stop……………………………………………………………………....23-24 scooter on, but not runni ng………………………………………...
Page 8
Page8 getting to know your x-treme x-250 (photo’s may vary).
Page 9
Page9 package contents your x-treme x-250 comes with the following items in the box. Please locate all of the following: 1. The x-treme x-250 scooter 2. 24v battery charger 3. Tool kit 4. Product handbook 5. Seat & seat post getting started please read and understand these instructions and the opera...
Page 10
Page10 fuse installation your scooter comes with a 20amp fuse located inside the tool kit pouch. Locate the fuse and insert it into the fuse holder located on the left side of the bike, under the foot plate. Seat and seat post installation 1. Insert the seat post into the bottom of the seat and tigh...
Page 11
Page11 riding 1. Make sure that all of the exposed bolts and screws are tightened. 2. Raise the kickstand to its upright position. 3. Push the on/off switch (located on the left handlebar) to the on position. 4. Put one foot on the deck of the x-250 while pushing off with the other foot, gently rota...
Page 12
Page12 tire and wheels the x-treme x-250 does not use an identical rim and tire assembly on the front and rear wheels. The wheels are two wheel halves (split rim) bolted together to make it easier to remove and replace the tire and tube. Tires can easily be rotated between front and back wheels. Tir...
Page 13
Page13 adjusting the belt the belt will come adjusted from the factory. However, it may be necessary to adjust the belt from time to time. The belt must be well aligned onto the sprockets in order to avoid uneven wear. This will result in shortened belt life. How tight should the belt be? if the b...
Page 14
Page14 maintenance recommended tools to adjust and service the x-treme x-250 you will need the following tools: allen wrenches: 3/4/5/6 mm wrenches: 10/13/13 mm open end wrench large adjustable crescent wrench philips head screwdrivers oil, grease or lubricant maintenance schedule proper c...
Page 15
Page15 how to install/replace fuse 1) locate the fuse holder inside the battery compartment under the foot board on the inside. 2) turn scooter off at the switch on the left handlebar. 3)) remove the seat post. 4) remove screws from foot board and remove to expose batteries and controller. 5) attach...
Page 16
Page16 frame. 6) after you have adjusted your belt and aligned your wheel tighten the axle nuts. How to remove foot deck 1) remove seat from seat post. 2) using a large straight screw driver remove the four (4) bolts holding the seat post base and remove post base from foot deck. 3) using the same l...
Page 17
Page17 9) these bolts also controls wheel alignment, be sure to center the wheel in the center of frame. 10) after you have adjusted your belt and aligned your wheel tighten the axle nuts. How to change charger socket 1) with foot deck removed access the battery connection and disconnect. Follow the...
Page 18
Page18 * in most cases if the scooter runs a shorter distance the batteries may be beyond their life cycle. How to check charger output tools needed – multi-meter set to dc voltage 1) determine the total dc voltage output of your scooter and set the multi-meter above that amount. 2) plug the charger...
Page 19
Page19 *if the motor is good and the batteries are charged the wheel will spin at full power in which case the controller may need to be replaced. *if the motor did not run then the batteries will need to be checked to confirm they are holding a charge. *if batteries are holding a charge then the mo...
Page 20
Page20 12) double check all nuts, bolts and cables. 13) with scooter on a box with the rear wheel not touching any surface test run and re-adjust belt as needed. How to replace inner tube 1) loosen the pinch nut on your brake hub to slide the brake cable out. 2) remove the axle nuts and chain tensio...
Page 21
Page21 charger voltmeter test: plug the charger into a wall socket, but do not plug it into the scooter. If your charger has three holes, place the probes into the holes to the left and right of the indented key. At the end of your charger port, the port that plugs into your scooter, you will notice...
Page 22
Page22 5) reinsert the new wires into the white connectors in the correct place. 6) now remove the old throttle and wires, mount the new throttle onto the handlebars, and tighten the setscrew. 7) install the footplate and you should be good to ride. Troubleshooting: no power in this situation we wil...
Page 23
Page23 when suspected you can very briefly arc across the battery terminals with a insulated wire to see if it produces a nice arc. . It is also possible to test some individual battery 12 volt cells using 12 volt motors or lights that will show you the available current capability. Is the 12 volt l...
Page 24
Page24 f) wires behind fuse assembly have come off due to improper replacement of fuses or loose wire connections to the battery. This is always due to the customer rotating the whole fuse assembly (when changing fuses) and twisting the 2 wires that are in the back of the fuse holder. You must open ...
Page 25
Page25 troubleshooting: is it my throttle or controller? (these tests require a digital vom) most e-scooter throttles use 'hall-effect' devices, not potentiometers (rheostats). A hall-effect device is a chip that responds to a movable magnet. If you have a digital vom (i would not use an analog resi...
Page 26
Page26.
Page 27
Page27 wiring diagram.
Page 28
Page28 battery wiring diagram.
Page 29
Page29 rear wheel assembly diagram.
Page 30: Do Not Return To Store!
Page30 do not return to store! If you need help call 1-253-777-0690 or go online www.X-tremescooters.Com/support/ for general information or parts visit www.X-tremescooters.Com revised 11/05/13.